Love it. Been wanting to do this swap for a long time.

man, that's one hell of a good job on that swap.... great video 👍

@jagersgarage490

2 ай бұрын

Thanks 👍

i have a 75 f250 4x4 with a Perkins 6 liter 6 cyc and a fuller 10 speed. i love that trans there is only a 400 rpm drop between gears so the engine is never out of its power band. im running a 14 inch twin disc clutch out of a 60 series chevy. im building a pickup for a friend with the same combo but its getting a 16 inch twin disc. hes towing a 40 foot fifth wheel travel trailer.

@jagersgarage490

3 жыл бұрын

Sounds like a sweet combo

@keelandavis

4 ай бұрын

Post a video of it!

I did this on my 01 DRW , didn't have to worry about a transfer case, sure wish i could weld as good as you did in the inside of the cab. Also like the Trans mount you made out of the OEM, I used the trans mounting holes in the frame and fabricated perches for rubber mounts on both sides, then fabricated two L shaped mounts that bolt to the side of my FSO8406 and rest on the mounts.

@jagersgarage490

3 жыл бұрын

Thank you for your kind words. The way you did yours sound like the way its usually done in med and heavy duty trucks.

@bccoggin

2 жыл бұрын

Do u happen to have pics. I'm doin a fs5205a in my 94 dually an wanted to see how it would fit. G56 an an eaton 5 speed are qbout the same height so I'm hoping I don't have to cut the cab

I am getting ready to do this swap on a 93 1st gen! Great video!

@jagersgarage490

2 жыл бұрын

Thank you

@jarrett754

Жыл бұрын

Did you ever do the swap? I’m contemplating doing the same thing on my 93 d350

@michaelcowan7456

Жыл бұрын

@@jarrett754 I did the Eaton fuller 6 speed OD swap it was very straight forward. I did a detached 205 transfer case, 2in body lift and built a crossmember. Had to build a bracket for the slave cylinder to reverse the direction of force. Other than that it was plug and play.. also mine was a D350 ex cab dully, I did the 4x4 swap. I used a Dana 70 rear end and Dana 60 kingpin front end.

@jarrett754

Жыл бұрын

@@michaelcowan7456 do you think it was be just as easy doing it without the 4wd swap? I really like the fact that my truck has stayed mostly original but the getrag is getting harder to find parts for as time goes on. And the previous owner had their way with it (find em grind em lug the crap out of it style of driving) so I would really like to take on a more robust solution. The problem is that truck is currently my daily driver so I’m hoping for a way I can do the entire swap in the span of 3-4 days

@michaelcowan7456

Жыл бұрын

@@jarrett754 is there a way to PM you?

Ok very cool thanks ill have to show you some pic of mine when it done I've got an flywheel housing and bell housing along with transfer case and transmission I just have to get a the e fly wheel and clutch and starter I'm ordering them this weekend hopefully thank you again for all your help

@jagersgarage490

4 жыл бұрын

Glad I could help. I am on Facebook as jagers garage (personal) or team fishballs (projects page).

Nice work man! The mounts for the divorced t case look like they could be beefier and also go frame rail to frame rail to resist rotational torque on the bottom as well as the top. But man nice work!

@jagersgarage490

2 жыл бұрын

Thank you It goes frame rail to frame rail across the top especially a C channel arched across made out of 3/16 plate.

@NealORussa

2 жыл бұрын

@@jagersgarage490 gotcha. I had a Suzuki samurai rigged up for off-roading on Toyota axles and 36's. They have divorced tcase. I ended up getting a laser cut ring that went around the entire case and grabbed every mounting bolt that held the front and back case halves together. If you didn't do that they always seemed to crack. Granted a lighter case, but I always just assumed there was a lot of torque on them especially in low range.

@jagersgarage490

2 жыл бұрын

Its mounted basically the same as the truck it come out of. If I were off roading I'd definitely add more support but it's just a tow rig. I don't ever use low range first gear is almost 9:1

Cool beans,im puting the same trans on in a 68 c10 im making 4 wheel drive with a 6.5 detroit

@jagersgarage490

Жыл бұрын

Nice

Great job!!! Do you want to do another one? I’m tired of fixing my 48 RE time to do this conversion.

@jagersgarage490

2 жыл бұрын

I dont have the exact figure handy but its around $3500 just in labor.... fabrication takes time.

Loved the video any chance you can do a walk around of your truck with the 10 speed how you did the on board air for hi low etc?

@jagersgarage490

3 жыл бұрын

I should have time this weekend to do that

@jagersgarage490

3 жыл бұрын

kzread.info/dash/bejne/dYdtqcVqqK-cqqw.html

Very nice work I going to install a 6 speed in my 95 Dodge 4x4 . Would like to see the 10 speed truck you built . Thanks

@jagersgarage490

3 жыл бұрын

Thank you. If you check my channel I have a walk around of the 10 speed.

@Mad.Man.Marine

3 жыл бұрын

Jagers Garage I have an 08 with the auto 6 speed. She is on her way out. Can I do this conversion in mine? I realize the bell housing will bolt up. What I'm wondering is about the transfer case. Will I need to do the divorced transfer like this? I already have a tuner. So trouble codes can be cleared.

@jagersgarage490

3 жыл бұрын

Yes you will need a divorced transfer case unless you want to pay or have access to a machine shop to make a married mount and coupler. There is a guy on the cummins forum that did it and shared lots of info.

@Mad.Man.Marine

3 жыл бұрын

@@jagersgarage490 I actually have a machine shop in my boat shop lol. Prob be way easier to just do a divorced setup. Still not sure if I will even do it.

@jagersgarage490

3 жыл бұрын

I would say if you have the means do it married then you don't have to build another crossmember or worry about a mid shaft or setting the angles. I would have but machine shops here are very expensive.

Love the video and information on it. Thank you Very much. This cleared up a few things for me as I am researching this some. Curious if you know if this would work on a common rail? I have an 06 with the g56 and 177, miles. I am wanting to do a 13spd on it. My biggest concern is the SAE#2 bell housing if it’ll bolt to the back on the common rail. I have not found anything online about common rails being swapped to 10spds. Thank you and love the videos. Keep them coming!

@jagersgarage490

4 жыл бұрын

It can be done on a common rail should be the same flywheel housing that I used as I'm pretty sure the blocks are the same. If the block are different you will just have to find an SAE2 flywheel housing for the common rail.

@godspeedparadeteam

2 жыл бұрын

Did you do the swap? I have a 2004 ram 3500 5.9 with the g56.

@GarageOperator

2 жыл бұрын

@@godspeedparadeteam I have not yet. I’m waiting since I have other things that require the funds at the moment and my transmission is still working fine. But I will definitely be doing it in the future. I will also do videos on it when I do the build. Since there are not a lot out there and none on a newer coming rail truck. I will also be doing mine In 4wheel drive version

@bccoggin

2 жыл бұрын

They don't make a common rail sae 2 clutch housing. One bolt hole is different an the common rail have a cam seal inset into the factory adapter plate. So a sae 2 housing will work just one hole will not line up. Then have a cam seal groove machined in it an bolt it up an go on about your day

@jagersgarage490

2 жыл бұрын

The big problem is finding the housing it's hard to get info. I'm am very confident the common rail housing exists as they used common rails in freightliner fl60s .

Con doble disco queda con más agarre y no es un peso demasiado ya que cuando viene en camiones ford viene así y acelerar normal

I was cussing for you on putting the fly wheel in! Jesus Christ!

@jagersgarage490

4 жыл бұрын

Yeah it's a pain not much room to work.

Great videos I am looking to do my own on my 96. is there any chance you can get me the part number for the fly wheel housing and starter you used in these conversions?

@jagersgarage490

3 жыл бұрын

They are in the description.

Top notch! Any chance you have part numbers for the 1710 slip yoke and 1550 yoke?

@jagersgarage490

2 жыл бұрын

I cant remember or find the recipe for what I used it was several years ago. But this is the website I used. I got the ones that were a little longer because they were quite a bit cheaper this is the 1710 page they also have a 1550 page.

I'm doing this swap now with a fs5406 I converted to an overdrive trans. You saved me a ton of time on the trans cross member with those measurements you gave. How did you do the clutch release did you cut the factory lever on the trans and drill a pocket in it for the slave cylinder rod to rest in . Great video bud

@jagersgarage490

Жыл бұрын

For the clutch release I cut the lever on the trans and drilled a pocket

@WeldWerx

Жыл бұрын

@@jagersgarage490 do you remember how much you cut off the end so it has enough throw but not to much

@jagersgarage490

Жыл бұрын

How much was cut off depends on the arm you have. From the center of the shaft to the end when cut was about 3in with the 1/4 in deep hole for the rod at about 2.5in

@WeldWerx

Жыл бұрын

@@jagersgarage490 thanks man I just finished my trans mount I'm abt to start on the clutch release thanks again for the info

Where's the driving video? I'm eagerly waiting for it!

@jagersgarage490

3 жыл бұрын

I'm still waiting on the owner to finish the interior.

How did you figure out the proper throw for the slave cylinder? Did you have to mess around with different length arms until you got the proper travel?

@jagersgarage490

3 жыл бұрын

I use my calibrated eye lol and it worked the first time.

Ok when I’m searching for the bell housing I just type in sea 2 bellhousing and looking for a medium duty 10 speed Eaton fuller transmission I’m wanting to do the same thing but I want to get as much information as I possibly can to do this

@jagersgarage490

3 жыл бұрын

For the bellhousing the best bet is to get the eaton overhaul or parts breakdown manual for the 6610 or 610 it will have bellhousing part #s in it. You can get/read the manuals on line.

Where did you source your sae 2 bell housings for the Cummins? Just doighin around or is there someone who stocks them?

@jagersgarage490

3 жыл бұрын

I have bought 2 of them on e-bay you can find them other places but e-bay seems to be the cheapest. A new one from a semi dealer was about $1200.

Does the engine and transmission have to be at one degree incline? I didnt understand very well why you used the angle meter

@jagersgarage490

3 жыл бұрын

Rear sump engines are usually angled back to help the oil drain to the sump in the oil pan. I took a measurement stock before I removed anything then set it at the same angle when I installed the new transmission mount.

Would this work on a first gen 350 2wd automatic. Dually ? Also what gears in the diff would be ideal for daily driving

@jagersgarage490

2 жыл бұрын

Yes it would work a 2wd would actually be alot easier. As for gears that really depends. If you get an overdrive trans it will be basically the same as stock. If the trans is not overdrive or you have larger tires. Go online and you can find a calculator where you put in tire size trans, axle gears and speed. Then it will give you an rpm and you can decide from there. The most fuel efficient rpm for a stock 12 valve is about 1700

What is the difference ratio, I installed that same gearbox and the gears are very short, in 6th gear it reaches 60 km at almost 1500 rpm, i have ram 2500 2007

@jagersgarage490

4 ай бұрын

I'm pretty sure it was 3.54

Hey - i sure like your conversion vids but why the background racket (music) WHILE you talk ?

@jagersgarage490

3 жыл бұрын

The reason there is music when I talk is because the editing software I was using at the time would not allow me to split or mute the music.

FSO6406 VS NV5600... Do you still PREFER the Eaton? I am asking your thoughts...

@jagersgarage490

3 ай бұрын

It was in a buddy's truck he still prefers the 6406. They shift about the same but the 6406 hasn't needed replaced if he had the 5600 he would have had to replace it again by now

I love this swap but I think I would have used a kit to divorce your stock T case. The np271/3d is actually a stronger case than those old np205s

@jagersgarage490

2 ай бұрын

I looked into that at the time I could not find a kit to divorce an NP241. I did find one for I believe it was the NP271 but I don't have a 271 and had no luck sourcing one locally.

What did you Use for a clutch and the name of you drive shaft supplier

@jagersgarage490

4 жыл бұрын

For mine I went to a heavy truck shop and bought one that fit my needs. For this build the owner supplied the clutch with no box so I have no info about it. I ordered the front and rear drive shafts from Tom woods in California 4xshaft.com for the shaft between the transmission and transfer case and all the flanges/yokes were from www.northerndrivetrain.com

I have a 99 with a 5 speed. The goal is to one day get a 1000 hp p pump 24v in it. It currently has approximately 500 hp which is about all the fuel you can get out of a stock vp44. But ive already blown the trans once. Thinking ill have to do something like this? How much money was this approximately? How much power could a baby 10 take? Id probably do something else for the t case

@jagersgarage490

3 жыл бұрын

Cost really depends on how much of a hurry you are in and how much you search for deals. Mine was close to $5000, I paid $300 for the trans but almost $3000 for drive shafts. For strength the nv4500 is rated at about 400ft lbs at I think 12,000GVW the RTO6610 is rated at 660ft lbs at 55,000 GVW. I don't have any experience using one with that kind of power but based on there weight rating and seeing the size of the components I think it will hold up.

@yepitsme2536

3 жыл бұрын

@@jagersgarage490 thanks! Told me what i needed to know

@wyattlewis8671

3 жыл бұрын

You can get a good bit more than 500 out of a stock vp44. Most pumps in good shape will do 600, 650 is doable on a strong pump and there are a handful of people who have just barely broke 700. There's videos of guys with modded vp44s hitting near 1000 on just fuel and 1100+ with nitrous. 500 isn't even difficult to get out of a vp44 nowadays

@yepitsme2536

3 жыл бұрын

@@wyattlewis8671 corrected? Possibly on a perfect dyno. Most people 550 is tops. Personally haven't seen anything more out of a stock pump. Neither have I seen dyno sheets to back that. Not saying a few aren't, but most make no more that 550 wheel horsepower uncorrected

Do you happen to have or know of the part numbers for the intermediate rear and front drive shaft, I have the exact same setup except for mine is a 99 instead. But actually has 02 axles even has the same tcase. Mainly the rear and intermediate shaft are what's important because the front I'm not worried about I rarely ever use 4x4

@jagersgarage490

3 жыл бұрын

From northern drivetrain Spicer 3-4-10951-11 Northern Drivetrain 001051 Northern Drivetrain 00176 From drive-lines.com 4-2-669 1550 flange standard * 2.00 F-C 4-82-191 1550 2.5-16 X 4.562 270.04 27 6-3-2631KX SLIP YOKE ASSY You will also need a 1710 and 1550 U-Joint. Make sure the yoke on your transmission is a 1710 if it is not the 6-3-2631KX will not work for you. As for the front and rear driveshafts I don't have a part # I just called Tom woods driveshaft. Told them my u-joint sizes flange dimensions and length.

@TheHondaOutlaw

3 жыл бұрын

@@jagersgarage490 thank you so much

currently doing this swap. Got a 98 12v and a 6306. Is the slave cylinder you used the oem for the truck? i thought these clutches had a cable pulling on the arm not hydraulic

@jagersgarage490

Жыл бұрын

I used the OEM slave cylinder just built a bracket and modified the arm

@3monchii5

Жыл бұрын

@@jagersgarage490 awsome, thank you for the reply!

@3monchii5

6 ай бұрын

​@jagersgarage490 any idea on the part number for the pilot bearing that goes in the flywheel? Is it the same as the oem dodge one?

@jagersgarage490

6 ай бұрын

I used this one Timken Single Row Ball Bearing - 305DD

@3monchii5

6 ай бұрын

@@jagersgarage490 again you're awsome, appreciate it

Hey. I have a 95 and its a stupid auto box. Have some ideas for the truck as I wa t it to be my farm truck in the next 5 years. Would love an Eaton fuller 10 speed but cannot find much info or ideas on keeping it 4x4. Divorced t-case I hear but how and where and a bunch of questions? Love to hear everyone's opinions. IC

@jagersgarage490

4 жыл бұрын

The ideal 10 speed are know as the baby 10s they weigh about 400lbs... the RTO610 and RTO6610. For transfer cases many older pickups came factory with a divorced transfer case the one in the video is an NP205 from a ford.

@iancameron5724

4 жыл бұрын

@@jagersgarage490 the wheels are now in motion. Thank you. I'll find something used and slowly get the parts together. Truth be told, I'm actually bouncing around the idea of a 5 inch lift and chopping the cab and frame and stretching it into a full 4 door. Need to research how much that will affect my towing capacity. No point having a heavy hauler that can't haul! IC

@jagersgarage490

4 жыл бұрын

@@iancameron5724 Your welcome. I know what you mean about the heavy hauler. My current plan is to find an older F600 or Kodiak put a 4 door cab cummins and 18 speed.

@iancameron5724

4 жыл бұрын

@@jagersgarage490 f@#k yeah!!!!!!!!

I have full p pump 8.3L with 6 speed. Will all the trans parts bolt to a 5.9L?

@jagersgarage490

Жыл бұрын

Depends I am assuming the 8.3 is and SAE #2 if it is then if you have an SAE #2 flywheel housing and flywheel for the 5.9 then yes. The 8.3 flywheel housing will not fit the 5.9.

@WWRT88w

Жыл бұрын

@@jagersgarage490 That was my main question. I'll look for a #"matching" flywheel housing for my 5.9L. Thanks!

Greetings i'm folow You from México and got cuestión for You what serial number it's in the 4*4 Transfer case

@jagersgarage490

2 жыл бұрын

With my 10speed I have a Dana 21 the 6 speed I did is an NP205 and a friend of mine who is doing a 15 speed is using an NP205. If cost was not a consideration I would use an Atlas II

What is the máximum speed? Cuz is not a overdrive transmission

@jagersgarage490

3 жыл бұрын

60mph is the max I'm comfortable cruising at because of the rpm. but the owner does 65mph it has 3.54 gears and 37in tires and he plans on 40s or 42s.

Did you ever make a test drive video

@jagersgarage490

4 жыл бұрын

Not yet once the ower gets the interior in I plan to.

Hi is possible to send me more information about flywheel like part # and clutch set up too any help well be appreciated trying to do the same exact swap thanks

@jagersgarage490

4 жыл бұрын

Oshane Henry I ment to put it in the video but forgot. IATCO 3921263-IAT B Series Cummins Flywheel (5.9-L) Replaces 3921263 & 4933458 www.amazon.com/dp/B014V0H48A/ref=cm_sw_r_other_apa_i_GW4PEb7ZHVMM9 DB Electrical SNK0021 Starter Unit Type: Starter Voltage: 12 Rotation: CW Teeth: 10 Starter Type: OSGR Replaces OEM Numbers: AC DELCO: 323-504 ARROWHEAD: SNK0021 ARROWHEAD (OEM): IMI25002-017, NK0-23000-2238 CARGO: 112253 CUMMINS: 3675172RX, 3924410, 3935071 DELCO: 10461477, 10465151, 10465314, 10479615, 10479618, 10479625, 10479638, 10479641 FORD: F3HT-11001-DB, F3HT-11001-DC, F3HZ-11002-B, F4HT-11001-BA J & N: 410-12121, 410-12757 J & N (OLD): 410-12121R LESTER: 6585 MOTORCRAFT: SA-803 NIKKO: 0-23000-2238, 0-23000-2388, 0-61000-0190, 0-61000-0220 NSA: STR-7056 REMY LIGHT DUTY: 63145 UNIPOINT: STR-7056 WAI: 6585N www.amazon.com/dp/B0081SBZ8E/ref=cm_sw_r_other_apa_i_zZ4PEbH0530T4 Timken 305DD Pilot Bearing www.amazon.com/dp/B000BZ6XD2/ref=cm_sw_r_other_apa_i_Q54PEbE637WSX Flywheel housing 3921296

@jagersgarage490

4 жыл бұрын

Oshane Henry for the clutch you will need to get the transmission input shaft size and splin thengo to a heavy truck shop and talk to them to figure out what you can get for the power you are making and if you want it to be a push or a pull type.

@oshanehenry6946

4 жыл бұрын

@@jagersgarage490 THanks for all your help you really did a good job on that truck

@jagersgarage490

4 жыл бұрын

Oshane Henry Thank you I'm glad to help.

How much did it cost the customer in parts to do this swap?

@jagersgarage490

3 жыл бұрын

Just parts including the transmission it was about $8,000

This has been a dream of mine for a long time where are you located and how can I get in touch with you

@jagersgarage490

3 жыл бұрын

I'm in Alaska you can contact me on Facebook at jagers garage or team fishballs.

can you use the stock dodge transfer case?

@jagersgarage490

2 жыл бұрын

Its possible but you have to convert the stock transfer case to be divorced or convert the transmission to accept a married transfer case

Can I hire you to do this swap on a 1999 Freightliner MT-45? Has the AT545 SAE #3 behind a 6BT

@jagersgarage490

2 ай бұрын

I suppose it's possible but I'm I'm alaska so unless the truck is in alaska I don't see it happening

@theselimt

2 ай бұрын

@@jagersgarage490 Haha I don't think I want to drive the AT545 that far. But thank you for the video, I'm looking for a donor right now.

What about clutch master and slave cylinders, which ones you used?

@jagersgarage490

2 жыл бұрын

Factory dodge just made a mount for slave

@ivonivan1169

2 жыл бұрын

@@jagersgarage490 good to know, thanks

@ivonivan1169

2 жыл бұрын

@@jagersgarage490 which clutch to use with this setup, any '10 spline 14 inch' kit?

@jagersgarage490

2 жыл бұрын

The big thing once you get into commercial clutches is shaft diameter and if it's a push or pull clutch there are many different ones for each set up available just need to figure out what you need at research to find the clutch you want

Where can I see your ten speed conversion I’m doing one in my 99 24 valve

@jagersgarage490

4 жыл бұрын

Unfortunately I did the 10 speed before I had a KZread channel and didn't take any video. Installing the 10 speed was the same as the 6 speed other than the air system and i did a 2in body lift instead of cutting out the transmission tunnel. If your 10 speed has an SAE 2 bellhousing you can use all the parts listed in the description.

@jamiehoney82

4 жыл бұрын

What is the part number for the fly wheel housing I’m only finding sae 3 on Cummings dinner engines

@jagersgarage490

4 жыл бұрын

Flywheel housing 3921296

@jagersgarage490

3 жыл бұрын

kzread.info/dash/bejne/dYdtqcVqqK-cqqw.html

Why didn't you video the first drive?

@jagersgarage490

Жыл бұрын

Didn't think at the time it would be interesting to people as it's just like driving a normal 6 speed.

Where are you located? I would like you to do one for me

@jagersgarage490

3 жыл бұрын

I am in Alaska

How much do a conversation cost

@jagersgarage490

2 жыл бұрын

Cost really depends on how much of a hurry you are in and how much you search for deals. Mine was close to $5000, I paid $300 for the trans but almost $3000 for drive shafts. For this one the owner paid $1700 for the trans but I got the drive shafts from tom woods instead of locally so the were $1000 instead of $3000

@TouchDownDavis

2 жыл бұрын

@@jagersgarage490 thanks for the response

No follow up?!?

@jagersgarage490

2 жыл бұрын

Not at this point the owner wanted to do some rust repairs before finishing the interior and getting bigger tires he is currently in the lower 48 so I don't know if a follow up will happen.

Good video. Lousy music...

@jagersgarage490

4 жыл бұрын

Glad you like the video... unfortunately it's hard to find good music without a copyright.

@t63a700

3 жыл бұрын

@@jagersgarage490 Leave the music out of the videos. Copyright problem solved and viewers will not complain about the music. To me the music is lousy and distracting from the video content. Great video otherwise.

why the garbage "music" ?