3.6L VVT lifter Knock fix without removing timing chain!
Жүктеу.....
Пікірлер: 154
@thayerm13 жыл бұрын
2013 Jeep Grand Cherokee. Replaced all rocker arms and hydraulic valve lash on the right side of engine immediately after hearing ticking noise @119,328 on 8/26/21. One rocker arm was bad and 3 had some play. Job needed a valve cover gasket set, upper intake gaskets and Throttle Body gasket (not replaced). Replaced torque crews on PCV valve (old gasket used) with 5mm bolts for easy access. Remove the throttle body to access the 2 throttle body support bolts. Two bolts removed to relocate transmission fill tube. Special tools needed to secure the cam shaft. Lifter: 12x: MELLING JB7525 Rocher Arm: 12x: MELLING MR1332
@markwarner8336
Жыл бұрын
Do you think Melling is good or better than oem,I have a 2013 with 130,000 on it and was thinking about changing roller rockers,lifters,and timing chain kit ,I have no tick yet ,probably just jynked myself lol
@bempierre3 жыл бұрын
don't need take any brackets off to take upper intake off. Just remove bolts from back and in front use 4mm socket and take stem and bolt with it off. Then pull up and slide forward.
@markwarner8336
Жыл бұрын
Why didn't they do it like a old 22re Toyota engine, no lifters or rollers involved, the only reason I can think of is less noise,I'll take dependability over less noise any day lol
@georgeanddaddecker75639 ай бұрын
I would just pay for all new cams,rockers,and lifters while you were in there. Once and done. New spark plugs,coils,and Dorman oil filter housing too.
@leecrumble3921
6 ай бұрын
Yes you can bet if one was bad others are going to be bad soon. I've seen some with 5 rockers worn.
@dannysays99910 ай бұрын
good job man! how much did that job cost?.... i have this problem exactly!
@jeffreyzabawski48622 жыл бұрын
My 2021 Charger GT is Ticking and getting worse by the day. I just watched a video and it's ridiculous that this started a decade ago and still counting. I've been to two different Dealerships and both said it's normal of course. It's depressing hearing your Engine sound like shit and getting worse while your paying on it. Plus I bought it with intentions of keeping it for 10-15 years and no way in hell that's happening unless something changes.
@xCHAV0x
2 жыл бұрын
Dam man I’m sorry to hear that..yea dealerships don’t really care since that’s money for their service department…U could help it by running either Mobil 1 or royal purple oil or adding some oil treatments to slow the wear down.. the only way to get rid of the tick is to replace the valves..
@staceyandesme8023
2 жыл бұрын
I cried once the sound got worse…I can’t even turn it on nomore because it hurts my feeling so much
@alejandro22222213 жыл бұрын
Good. I have a problem with a 2011 dodge charger 3.6 with 190 thousand miles that I bought. I changed the expired oil, changed the spark plugs, cleaning the injectors, cleaning important sensors, acceleration body. Once it has been tuned, it will be given a 5w / 30 oil to clean the inside of the engine. I changed the synthetic caite x 10w / 30 again. THE DETAIL THAT I STARTED TO RING IN THE COLD THAT IS 1 OR 2 SECONDS AND NOW. I turn on the check ingine and the result is the camshafts and I have changed them, The 3 chain tensioners are changed and everything is fine. And the rattle came back. What will be the problem? They do not know what it can be. Can you help me?
@xCHAV0x
3 жыл бұрын
Where is the rattle coming from? Top, front, or bottom of engine? If the rattle is coming from the top then u might have to look into the lifters and rockers… if it’s coming from the front, check the length of the chain it could have stretched causing it to rattle… if it coming from the bottom then check the rod bearings. Hope this helps!
@alejandro2222221
3 жыл бұрын
good afternoon. Apparently the rattle comes from in front of the engine and the chain tensioners have already been changed. I have a video that causes the rattle. I would like to be able to send it to you by email. regards
@jeffreyzabawski4862
2 жыл бұрын
I've heard a few people that completely stopped their Engine Tick by switching to amsoil Signature and Redline when the vehicle had high milage like yours. I have a Tick going on that's getting worse with on 4,000 miles so I'm about to try one of them as well.
@Sam-656
Жыл бұрын
So did the rattle get fixed? I'd you did what happened?
@Mslilwetwet Жыл бұрын
What would this cost on a 2012 dodge journey lifter replacement
@SHADZ652318 күн бұрын
I have a tapping noise sounds like its coming from the top and also smoke coming from the bottom of my 09 2.7 litre engine does anyone know whats going on with it by any chance🤦🏾😂
@subliminal12843 жыл бұрын
Quick question, since you didn’t loosen all the caps what order did you tighten the caps down in? I’m in the middle of doing this and don’t want to screw things up when I torque the bolts back down
@xCHAV0x
3 жыл бұрын
Sorry for the late reply but I torqued them down the same way as if u had loosen all of them.... I went over the ones I didn’t loosen up just for good measures.
@subliminal1284
3 жыл бұрын
@@xCHAV0x Where is your shop located? Might use you in the future if by chance it’s close
@xCHAV0x
3 жыл бұрын
@@subliminal1284 I don’t have a shop I’m an independent mechanic..that one was at small dealer that hires me from time to time..but im located in NC
@donsantos7963
Жыл бұрын
@@xCHAV0x where in NC ?
@learnalittlelivealittle65023 жыл бұрын
How many rocker arms are there total? Would it be worth it just to replace them all while I have it tore apart?
@xCHAV0x
3 жыл бұрын
It’s 1 per valve so I believe it’s 24 of them.. yes replacing all its a good idea but that means removing the timing chain to remove the ones near the timing sprockets so might as well replace timing guides.
@timmaywoohoo
Жыл бұрын
If it ain't broke don't fix it. The more you mess around inside the valve cover the more likely you're gonna throw the engine out of time and if you have to ask this question you're not gonna have a good time timing one of these.
@trino142 жыл бұрын
Thanks man. I've tried alot of things. This might be it
@roberthunter19862 жыл бұрын
How much would a job like this cost on a 2014 dodge journey
@caylee3277
2 жыл бұрын
Hey did you get yours fixed? Mine is on a 2015 journey
@christinegabeautumnmommyha1248 Жыл бұрын
Hi, would you say this is a common issue with these cars? With the ticking noise? Also do you think this is something that one can do on their own if they followed how you did it because I have this issue currently, and would like to know.
@xCHAV0x
Жыл бұрын
It’s is a common issue..if u try getting the part from the dealer most of the time it will be on back order..it’s not a bad DIY job as long as u don’t let the timing move out of time.
@antluis3444 Жыл бұрын
Im having this problem on my dodge charger and my question is, is it worth it to fix the lifter, rockers, and camshafts or should i just trade the car in or sell it? Every mechanic ive talked to about it get scared and say to get a new motor and dont wanna work on it. Took it to dodge and they wanna charge me 3500 to fix all lifters, camshaft and rockers.. so is it worth to fix??. Only has 120k miles. Thanks.
@xCHAV0x
Жыл бұрын
Really depends..usually the rocker is what goes bad and if u catch it on time u can save the camshaft and u would only need new lifter and rocker… if u have a little experience with cars it’s not too hard to do just don’t let it jump time while doing the job..but to me it be worth fishing if engine still fires up fine
@antluis3444
Жыл бұрын
@xCHAV0x cool thanks man
@jimmyfale63702 жыл бұрын
You didn't show you took the rocker arms off or how you moved the cam around or took off that rocker arm I need to see every detail of this process of fixing the tapping noise
@xCHAV0x
2 жыл бұрын
U loosen the cam caps in order for the cam to lift up enough to remove the rocker
@jimmyfale6370
2 жыл бұрын
@@xCHAV0x thank you very much for responding back to me also can I just tighten the caps back or do I have to torgue it down and is there a torgue sequence appreciate your answer back
@jimmyfale6370
2 жыл бұрын
@@xCHAV0x my Dodge caravan was making a tap tap noise took it to Dodge they changed the lifters they didn't mention anything about the rocker arms so both parts can make the tapping noise they charged me 3700.00 for the job where are the lifters and do you have a video for that job appreciate a response from you thank you PS: wanna do it myself this time don't wanna get charged another 3700.00 🙏
@jayfonseca44007 ай бұрын
What are the specs for the valve adjustable? Or is it just replacing the rocker and the lifter, and that's it?
@xCHAV0x
7 ай бұрын
If the valve hasn’t been damaged then there is no need to adjust it..just replace rocker and lifter and torque everything down to specs.
@byronwalton44593 жыл бұрын
I replaced a bad rocker arm on bank 1. Tick is gone, but still getting a P219a and P0301 (cylinder 1). Is it worth it for me to go back in and check the lifters? Could the bad arm that i replaced have damaged the 02 sensor or something? Thanks, man.
@xCHAV0x
3 жыл бұрын
Yes because usually the reason rockers go bad is because the lofter is stuck or got stuck at some point
@r.a.5625
2 жыл бұрын
Were you able to solve the problem? I have a bad lifter sound and p219a code. I replaced o2 sensors and map sensor. The code was there I replaced injectors and now p219a code is gone and I have p219b code. Does bad rocker arms lead to these codes?
@jeremyh6832 жыл бұрын
This has been a problem for quite a few years now and and dodge always says there's nothing wrong. I got this ticking especialy on idle and slow acceleration on my Chalenger and it only had 57000 miles on it. Never drove it hard and changed oil every 3000 miles. Even the Mechanics praised me on how good I kept the car up. Just a horrible engine.
@xCHAV0x
2 жыл бұрын
Yea these engine aren’t the best but if u catch the problem in time it keeps u for replacing camshafts!
@jeremyh683
2 жыл бұрын
@@xCHAV0xI understand that but doesnt matter how fast you catch it it shouldn't be giving problems like that that fast especially if your babying the car and when the car is still practically new still
@mails5054
2 жыл бұрын
@@jeremyh683 its basically luck of the draw. I have the 3.6l and many go over 200k miles with no issues. I have the 3.6l in a jeep tho, seemingly less people talk about the issue in jeeps. The rocker arms and oil filter housing is what you have to look at mainly. Otherwise the engine is pretty solid. It almost seems like either you have this issue or you never will. Probably manufacturing or assembly not up to spec, ehh blame fiat. One went to 626k before it needed a rebuild! there is hope haha
@jraider43 Жыл бұрын
Can you tell me how to place those six but sensors
@santiagofranco16582 жыл бұрын
That is a good video thanks.👍
@dubbsackss203 жыл бұрын
Im doing the same job but I noticed that you didnt change the lifters.
@dubbsackss20
3 жыл бұрын
Also when my lobe is off the rocker arm just comes out, no compression on em. Any help?
@xCHAV0x
3 жыл бұрын
I did replace the lifter but I didn’t show it..when I’m showing the rocker u can se the lifter is out but since the rocker was the one that was the one making the noise I forgot to show the lifter.. if the lifter that u are trying to remover is being pushed down just turn the engine by hand till u see that the lobe of the can has moved up and the valve is close that way u don’t have to lift the cam as much and u don’t run the risk of jumping time or anything like that.
@dubbsackss20
3 жыл бұрын
@@xCHAV0x My rocker just falls out with the lobe off. Could it be my lifters are stuck in the down position?
@xCHAV0x
3 жыл бұрын
If the can it’s not losses and rocker just fall off then yes the lifter is stuck.. also make sure if u going to put mew lifters in, to submerge the new lifters in new oil to charge them.. u can use a cup and just drop the lifters in there but make sure to pour enough oil to cover them completely and let them sit for about 15 min before dropping the new lifter in.
@dubbsackss20
3 жыл бұрын
@@xCHAV0x your awesome man! Thanks
@Kdfclincher11 ай бұрын
Is it crazy to just replace the bad lifter and not the whole thing cam and all?
@xCHAV0x
11 ай бұрын
Yes but you will have to replace the rocker and the lifter and only if the camshaft itself has not been damaged… that’s what I did on the video I did not replaced camshaft or cam gears ⚙️
@arkana84535 ай бұрын
What is the cause of this defect?
@davidbachy5627 Жыл бұрын
Fantastic Video!!! Thanks!
@hksjoshua2 жыл бұрын
So did you replace the lifter also or rocker arm only?
@xCHAV0x
2 жыл бұрын
I replaced lifters and rocker.
@larrypippin7854
2 жыл бұрын
Why didn't you show any of it? Kinda important don't ya think?
@dezman2003
2 жыл бұрын
@@larrypippin7854 Exactly, there are dozens of videos of rocker arm replacements. Dude titled this as a lifter problem and then fucked off on actually showing anything at all regarding lifters. Thanks a lot you genius, thanks for wasting our time.
@stevencruz64782 жыл бұрын
Would you recommend chaging the timing chain/water pump when replacing the lifters?
@xCHAV0x
2 жыл бұрын
If you’re planning on removing the chain then yes but if not then not really..this engine is not known to stretch the chain or a faulty pump.
@stevencruz6478
2 жыл бұрын
@@xCHAV0x thank you, just replaced the camshaft, rocker, lifters, timing chain, water pump, spark plugs and coils. I still get a violent shake when in gear. Any ideas? engine mounts?
@shameelshemi8057
2 жыл бұрын
@@stevencruz6478 mine also small shaking when engine is on.
@abrahamrodriguez1693
Жыл бұрын
@@stevencruz6478 motor mounts
@tommason47022 жыл бұрын
Thanks for the great video!! BTW, if cam shaft has to be replaced, rear side is considered left or right side when ordering the part? Thanks for your help!
@xCHAV0x
2 жыл бұрын
One cam Is exhaust the other is intake..u would ask for either a intake camshaft or exhaust camshaft..u can tell by looking at the cams..the one closer to the center of the engine is the intake the one in the outer side is the exhaust camshaft!
@tommason4702
2 жыл бұрын
@@xCHAV0x Looks like you did not understand my question. There are two sides to the engine: front 3 cyl and rear 3 cyl. I checked Mopar and they refer to left or right side for everything, not front or rear. My question is: "rear" corresponds to right or left side of the engine? Thanks for your help.
@xCHAV0x
2 жыл бұрын
@@tommason4702 oh ok..the right bank..pistons 1,3,5 will be to the rear..left bank..pistons 2,4,6 is up front
@tommason4702
2 жыл бұрын
@@xCHAV0x Thanks a million! This really confused me and I could not get this information anywhere. It's a lot of headache if you order the wrong part. You are my life saver!
@slimtrim22 Жыл бұрын
How much did you charge for that job?
@leohernandez1212 жыл бұрын
How long did it take to change the lifter.. Shop hrs???
@xCHAV0x
2 жыл бұрын
I would say 5~6 that’s taking it easy.
@DavidMartinez-mc1fy Жыл бұрын
How long did it take you to do it
@huntermcauliffe5453 жыл бұрын
I have the same ticking noise but when we took everything apart all the rockers were fine and now we are lost as to what it could be
@xCHAV0x
3 жыл бұрын
This might be dumb question but did u check the lifters? They are the ones that fail by getting stuck..in my case the lifter got stuck up and caused the rocker to get damaged but if the lifter gets stuck down then the rocker is just gonna be loose causing the noise also inspect the cam lobes
@huntermcauliffe545
3 жыл бұрын
@@xCHAV0x The lobes weren’t damaged and none of the rockers were loose
@xCHAV0x
3 жыл бұрын
There has to be one that is making the noise.. unless ur tapping is coming from the bottom… they might not be too loose but if a lifter is not functioning properly it will tap since is not retracting and expanding as it should
@huntermcauliffe545
3 жыл бұрын
@@xCHAV0x if it’s more underneath what could that be because it’s not knocking like it would if it was a rod problem
@xCHAV0x
3 жыл бұрын
Check your exhaust manifold gaskets they can cause a sort of tick noise..Try using a Stethoscope to pin point the source of the noise.
@Deedee-mu4xv11 ай бұрын
Did you change it without touching the cam phasers ?
@xCHAV0x
11 ай бұрын
Yes.. timing was not disturbed.
@Big-Hit2 жыл бұрын
I have the same issue my brotha, how much do you charge to fix the lifters on a 2014 dodge caravan?
@xCHAV0x
2 жыл бұрын
I charge $450 to replace all lifters
@Big-Hit
2 жыл бұрын
Where are you located
@xCHAV0x
2 жыл бұрын
Statesville NC
@caylee3277
2 жыл бұрын
@@xCHAV0x hey I'm getting this sound on a 2015 dodge journey, I'm in Raleigh how far from there are you
@caylee3277
2 жыл бұрын
@@xCHAV0x they are saying lifters and rocker arms
@martinpadilla90532 жыл бұрын
En qué lugar estás tengo ese problema texteame tu dirección estoy en California
@YouYa01-3 жыл бұрын
How much roughly does it cost to fix rocker arms ? I got 500$ saved and I’m hoping it’s my lifter but just wondering
@xCHAV0x
3 жыл бұрын
At a shop about $1200+ ...an independent mechanic like my self around $250 (if they are honest).. if you want to do it yourself it’s about $130 in parts, that’s including the intake manifold gasket, valve cover gaskets, and rocker..rockers are about $15~$25 each so it’s not bad.
@arnejohnson8623
2 жыл бұрын
It's the labor not the parts that'll get you ... valve lifters and rocker arms are all pretty cheap.
@donsantos7963
Жыл бұрын
You still do this?? Got one like this now
@donsantos7963
Жыл бұрын
@@xCHAV0x You still do this?? Got one like this now close to NC
@xCHAV0x
Жыл бұрын
@@donsantos7963 sorry man just seen this…but yes Im still doing them.
@jeremyh6832 жыл бұрын
Thanks alot Fiat/Chrysler. Cheap parts.
@r.a.56252 жыл бұрын
Does camshaft not need to be come out to replace the rocker arms?
@xCHAV0x
2 жыл бұрын
No u loosen up the cam caps enough to free the rocker arms..if needed turn engine by hand to release tension on rocker arm but spin engine with all caps tightened down.. once the cam lobe is pointing up that will make it easier to remove by loosening a few caps.
@r.a.5625
2 жыл бұрын
@@xCHAV0x Thank you so much
@MECHANIC1 Жыл бұрын
Thanks man!
@GoldenArmz9102 жыл бұрын
How long could your drive it with that sound without it blowing up?
@xCHAV0x
2 жыл бұрын
Depend on the severity of the sound but u really don’t wanna risk much time on that… it could go from being a $150~$500 repair to a $1,500~$3,500 repair.
@GoldenArmz910
2 жыл бұрын
@@xCHAV0x mannnn how far are you from fayetteville Nc?
@Kdfclincher11 ай бұрын
Does driving it with the tick do more damage?
@xCHAV0x
11 ай бұрын
Yea depending on how severe it is it can damage more parts and eventually cause bigger issues.
@gnd111 Жыл бұрын
Thats not a VVT failure....its chinese roller rocker needle bearing failing. The collect in your oil pan also..lol..ask me how i know. Newest revision is AH in the part number
@streetwearfluent72373 жыл бұрын
Story of my life
@kenbrou22503 жыл бұрын
Chavo are you in Texas? I want to pay you to do this to my ram
@xCHAV0x
3 жыл бұрын
I actually just got to TX this weekend but I will only be here this week then I’ll be in NC.. I could do the job this week if u would like I’m located in Tyler tx
@kenbrou2250
3 жыл бұрын
@@xCHAV0x I want to send you my number or something, no private message o. KZread
@junioraviles3192
3 жыл бұрын
@@xCHAV0x im from marshall tx 😎 thnx for postin the video my wifes car has 2 that i know of that are bad. Im currently livin in florida so just gonna get my mechanic to tear down and replace.
@brianheiden66232 жыл бұрын
Thats a rocker arm bro lifter is underneath lol.
@xCHAV0x
2 жыл бұрын
U don’t say?….the lifter failed causing the rocker to fail.. lifters and rocker arms were replaced.
@chriswilliams33272 жыл бұрын
Will bad lifters give me bad acceleration
@xCHAV0x
2 жыл бұрын
Depending on how damaged it is if it’s to the point where it won’t engage the valve anymore then yes but u would definitely have a loud knocking sound coming from the top end.. look for vacuum leaks that’s more common to cause a bad acceleration
@DavidMartinez-mc1fy Жыл бұрын
How long did it take you?
@xCHAV0x
Жыл бұрын
About 5~6 hrs depending on how many breaks u take
@hassanaldossari25093 жыл бұрын
What is your camera 📷
@xCHAV0x
3 жыл бұрын
Just an IPhone XS Max..
@stillballin99673 жыл бұрын
Yo chavo, where are you located ?
@xCHAV0x
3 жыл бұрын
I’m located in Statesville NC
@paul911243 жыл бұрын
If not fixed,what's gonna happen?
@xCHAV0x
3 жыл бұрын
It will wear dow the cam and eventually break, sending metal pieces into the oil and bigger pieces will get stuck in other valve springs causing them to stay open and causing farther damaged to the engine.. not worth the risk..
@paul91124
3 жыл бұрын
@@xCHAV0x Thanks again,but what cause from breaking? Factory's misasenbury or drove too fast by running engine or use cheap oil? Please let me know thanks.
@xCHAV0x
3 жыл бұрын
Seems to be a manufacturing error because almost every 3.6 from dodge has the same problem..they have revise the engine in these past few year so it not as common on 2017 and up
@paul91124
3 жыл бұрын
@@xCHAV0x Thanks a lot.
@hasanaletabi19382 жыл бұрын
We got more noises 😂
@sprinter350002 жыл бұрын
How many miles were on that engine?
@xCHAV0x
2 жыл бұрын
127k I believe
@jraider43 Жыл бұрын
Vvt*
@manuelornelas-xl4ib Жыл бұрын
Dogo Go Goback
@manuelornelas-xl4ib Жыл бұрын
Go back
@patrickmclaughlin60133 жыл бұрын
well, we know you don't like the 3.6's
@xCHAV0x
3 жыл бұрын
Actually I love them..they bring in lots of customers!
@patrickmclaughlin6013
3 жыл бұрын
@@xCHAV0x it seems that way I get the impression you could set up a shop dedicated to just swapping out those cam followers, lifters, phasers, and resealing that plastic thing with the oil cooler, and do very well.
Пікірлер: 154
2013 Jeep Grand Cherokee. Replaced all rocker arms and hydraulic valve lash on the right side of engine immediately after hearing ticking noise @119,328 on 8/26/21. One rocker arm was bad and 3 had some play. Job needed a valve cover gasket set, upper intake gaskets and Throttle Body gasket (not replaced). Replaced torque crews on PCV valve (old gasket used) with 5mm bolts for easy access. Remove the throttle body to access the 2 throttle body support bolts. Two bolts removed to relocate transmission fill tube. Special tools needed to secure the cam shaft. Lifter: 12x: MELLING JB7525 Rocher Arm: 12x: MELLING MR1332
@markwarner8336
Жыл бұрын
Do you think Melling is good or better than oem,I have a 2013 with 130,000 on it and was thinking about changing roller rockers,lifters,and timing chain kit ,I have no tick yet ,probably just jynked myself lol
don't need take any brackets off to take upper intake off. Just remove bolts from back and in front use 4mm socket and take stem and bolt with it off. Then pull up and slide forward.
@markwarner8336
Жыл бұрын
Why didn't they do it like a old 22re Toyota engine, no lifters or rollers involved, the only reason I can think of is less noise,I'll take dependability over less noise any day lol
I would just pay for all new cams,rockers,and lifters while you were in there. Once and done. New spark plugs,coils,and Dorman oil filter housing too.
@leecrumble3921
6 ай бұрын
Yes you can bet if one was bad others are going to be bad soon. I've seen some with 5 rockers worn.
good job man! how much did that job cost?.... i have this problem exactly!
My 2021 Charger GT is Ticking and getting worse by the day. I just watched a video and it's ridiculous that this started a decade ago and still counting. I've been to two different Dealerships and both said it's normal of course. It's depressing hearing your Engine sound like shit and getting worse while your paying on it. Plus I bought it with intentions of keeping it for 10-15 years and no way in hell that's happening unless something changes.
@xCHAV0x
2 жыл бұрын
Dam man I’m sorry to hear that..yea dealerships don’t really care since that’s money for their service department…U could help it by running either Mobil 1 or royal purple oil or adding some oil treatments to slow the wear down.. the only way to get rid of the tick is to replace the valves..
@staceyandesme8023
2 жыл бұрын
I cried once the sound got worse…I can’t even turn it on nomore because it hurts my feeling so much
Good. I have a problem with a 2011 dodge charger 3.6 with 190 thousand miles that I bought. I changed the expired oil, changed the spark plugs, cleaning the injectors, cleaning important sensors, acceleration body. Once it has been tuned, it will be given a 5w / 30 oil to clean the inside of the engine. I changed the synthetic caite x 10w / 30 again. THE DETAIL THAT I STARTED TO RING IN THE COLD THAT IS 1 OR 2 SECONDS AND NOW. I turn on the check ingine and the result is the camshafts and I have changed them, The 3 chain tensioners are changed and everything is fine. And the rattle came back. What will be the problem? They do not know what it can be. Can you help me?
@xCHAV0x
3 жыл бұрын
Where is the rattle coming from? Top, front, or bottom of engine? If the rattle is coming from the top then u might have to look into the lifters and rockers… if it’s coming from the front, check the length of the chain it could have stretched causing it to rattle… if it coming from the bottom then check the rod bearings. Hope this helps!
@alejandro2222221
3 жыл бұрын
good afternoon. Apparently the rattle comes from in front of the engine and the chain tensioners have already been changed. I have a video that causes the rattle. I would like to be able to send it to you by email. regards
@jeffreyzabawski4862
2 жыл бұрын
I've heard a few people that completely stopped their Engine Tick by switching to amsoil Signature and Redline when the vehicle had high milage like yours. I have a Tick going on that's getting worse with on 4,000 miles so I'm about to try one of them as well.
@Sam-656
Жыл бұрын
So did the rattle get fixed? I'd you did what happened?
What would this cost on a 2012 dodge journey lifter replacement
I have a tapping noise sounds like its coming from the top and also smoke coming from the bottom of my 09 2.7 litre engine does anyone know whats going on with it by any chance🤦🏾😂
Quick question, since you didn’t loosen all the caps what order did you tighten the caps down in? I’m in the middle of doing this and don’t want to screw things up when I torque the bolts back down
@xCHAV0x
3 жыл бұрын
Sorry for the late reply but I torqued them down the same way as if u had loosen all of them.... I went over the ones I didn’t loosen up just for good measures.
@subliminal1284
3 жыл бұрын
@@xCHAV0x Where is your shop located? Might use you in the future if by chance it’s close
@xCHAV0x
3 жыл бұрын
@@subliminal1284 I don’t have a shop I’m an independent mechanic..that one was at small dealer that hires me from time to time..but im located in NC
@donsantos7963
Жыл бұрын
@@xCHAV0x where in NC ?
How many rocker arms are there total? Would it be worth it just to replace them all while I have it tore apart?
@xCHAV0x
3 жыл бұрын
It’s 1 per valve so I believe it’s 24 of them.. yes replacing all its a good idea but that means removing the timing chain to remove the ones near the timing sprockets so might as well replace timing guides.
@timmaywoohoo
Жыл бұрын
If it ain't broke don't fix it. The more you mess around inside the valve cover the more likely you're gonna throw the engine out of time and if you have to ask this question you're not gonna have a good time timing one of these.
Thanks man. I've tried alot of things. This might be it
How much would a job like this cost on a 2014 dodge journey
@caylee3277
2 жыл бұрын
Hey did you get yours fixed? Mine is on a 2015 journey
Hi, would you say this is a common issue with these cars? With the ticking noise? Also do you think this is something that one can do on their own if they followed how you did it because I have this issue currently, and would like to know.
@xCHAV0x
Жыл бұрын
It’s is a common issue..if u try getting the part from the dealer most of the time it will be on back order..it’s not a bad DIY job as long as u don’t let the timing move out of time.
Im having this problem on my dodge charger and my question is, is it worth it to fix the lifter, rockers, and camshafts or should i just trade the car in or sell it? Every mechanic ive talked to about it get scared and say to get a new motor and dont wanna work on it. Took it to dodge and they wanna charge me 3500 to fix all lifters, camshaft and rockers.. so is it worth to fix??. Only has 120k miles. Thanks.
@xCHAV0x
Жыл бұрын
Really depends..usually the rocker is what goes bad and if u catch it on time u can save the camshaft and u would only need new lifter and rocker… if u have a little experience with cars it’s not too hard to do just don’t let it jump time while doing the job..but to me it be worth fishing if engine still fires up fine
@antluis3444
Жыл бұрын
@xCHAV0x cool thanks man
You didn't show you took the rocker arms off or how you moved the cam around or took off that rocker arm I need to see every detail of this process of fixing the tapping noise
@xCHAV0x
2 жыл бұрын
U loosen the cam caps in order for the cam to lift up enough to remove the rocker
@jimmyfale6370
2 жыл бұрын
@@xCHAV0x thank you very much for responding back to me also can I just tighten the caps back or do I have to torgue it down and is there a torgue sequence appreciate your answer back
@jimmyfale6370
2 жыл бұрын
@@xCHAV0x my Dodge caravan was making a tap tap noise took it to Dodge they changed the lifters they didn't mention anything about the rocker arms so both parts can make the tapping noise they charged me 3700.00 for the job where are the lifters and do you have a video for that job appreciate a response from you thank you PS: wanna do it myself this time don't wanna get charged another 3700.00 🙏
What are the specs for the valve adjustable? Or is it just replacing the rocker and the lifter, and that's it?
@xCHAV0x
7 ай бұрын
If the valve hasn’t been damaged then there is no need to adjust it..just replace rocker and lifter and torque everything down to specs.
I replaced a bad rocker arm on bank 1. Tick is gone, but still getting a P219a and P0301 (cylinder 1). Is it worth it for me to go back in and check the lifters? Could the bad arm that i replaced have damaged the 02 sensor or something? Thanks, man.
@xCHAV0x
3 жыл бұрын
Yes because usually the reason rockers go bad is because the lofter is stuck or got stuck at some point
@r.a.5625
2 жыл бұрын
Were you able to solve the problem? I have a bad lifter sound and p219a code. I replaced o2 sensors and map sensor. The code was there I replaced injectors and now p219a code is gone and I have p219b code. Does bad rocker arms lead to these codes?
This has been a problem for quite a few years now and and dodge always says there's nothing wrong. I got this ticking especialy on idle and slow acceleration on my Chalenger and it only had 57000 miles on it. Never drove it hard and changed oil every 3000 miles. Even the Mechanics praised me on how good I kept the car up. Just a horrible engine.
@xCHAV0x
2 жыл бұрын
Yea these engine aren’t the best but if u catch the problem in time it keeps u for replacing camshafts!
@jeremyh683
2 жыл бұрын
@@xCHAV0xI understand that but doesnt matter how fast you catch it it shouldn't be giving problems like that that fast especially if your babying the car and when the car is still practically new still
@mails5054
2 жыл бұрын
@@jeremyh683 its basically luck of the draw. I have the 3.6l and many go over 200k miles with no issues. I have the 3.6l in a jeep tho, seemingly less people talk about the issue in jeeps. The rocker arms and oil filter housing is what you have to look at mainly. Otherwise the engine is pretty solid. It almost seems like either you have this issue or you never will. Probably manufacturing or assembly not up to spec, ehh blame fiat. One went to 626k before it needed a rebuild! there is hope haha
Can you tell me how to place those six but sensors
That is a good video thanks.👍
Im doing the same job but I noticed that you didnt change the lifters.
@dubbsackss20
3 жыл бұрын
Also when my lobe is off the rocker arm just comes out, no compression on em. Any help?
@xCHAV0x
3 жыл бұрын
I did replace the lifter but I didn’t show it..when I’m showing the rocker u can se the lifter is out but since the rocker was the one that was the one making the noise I forgot to show the lifter.. if the lifter that u are trying to remover is being pushed down just turn the engine by hand till u see that the lobe of the can has moved up and the valve is close that way u don’t have to lift the cam as much and u don’t run the risk of jumping time or anything like that.
@dubbsackss20
3 жыл бұрын
@@xCHAV0x My rocker just falls out with the lobe off. Could it be my lifters are stuck in the down position?
@xCHAV0x
3 жыл бұрын
If the can it’s not losses and rocker just fall off then yes the lifter is stuck.. also make sure if u going to put mew lifters in, to submerge the new lifters in new oil to charge them.. u can use a cup and just drop the lifters in there but make sure to pour enough oil to cover them completely and let them sit for about 15 min before dropping the new lifter in.
@dubbsackss20
3 жыл бұрын
@@xCHAV0x your awesome man! Thanks
Is it crazy to just replace the bad lifter and not the whole thing cam and all?
@xCHAV0x
11 ай бұрын
Yes but you will have to replace the rocker and the lifter and only if the camshaft itself has not been damaged… that’s what I did on the video I did not replaced camshaft or cam gears ⚙️
What is the cause of this defect?
Fantastic Video!!! Thanks!
So did you replace the lifter also or rocker arm only?
@xCHAV0x
2 жыл бұрын
I replaced lifters and rocker.
@larrypippin7854
2 жыл бұрын
Why didn't you show any of it? Kinda important don't ya think?
@dezman2003
2 жыл бұрын
@@larrypippin7854 Exactly, there are dozens of videos of rocker arm replacements. Dude titled this as a lifter problem and then fucked off on actually showing anything at all regarding lifters. Thanks a lot you genius, thanks for wasting our time.
Would you recommend chaging the timing chain/water pump when replacing the lifters?
@xCHAV0x
2 жыл бұрын
If you’re planning on removing the chain then yes but if not then not really..this engine is not known to stretch the chain or a faulty pump.
@stevencruz6478
2 жыл бұрын
@@xCHAV0x thank you, just replaced the camshaft, rocker, lifters, timing chain, water pump, spark plugs and coils. I still get a violent shake when in gear. Any ideas? engine mounts?
@shameelshemi8057
2 жыл бұрын
@@stevencruz6478 mine also small shaking when engine is on.
@abrahamrodriguez1693
Жыл бұрын
@@stevencruz6478 motor mounts
Thanks for the great video!! BTW, if cam shaft has to be replaced, rear side is considered left or right side when ordering the part? Thanks for your help!
@xCHAV0x
2 жыл бұрын
One cam Is exhaust the other is intake..u would ask for either a intake camshaft or exhaust camshaft..u can tell by looking at the cams..the one closer to the center of the engine is the intake the one in the outer side is the exhaust camshaft!
@tommason4702
2 жыл бұрын
@@xCHAV0x Looks like you did not understand my question. There are two sides to the engine: front 3 cyl and rear 3 cyl. I checked Mopar and they refer to left or right side for everything, not front or rear. My question is: "rear" corresponds to right or left side of the engine? Thanks for your help.
@xCHAV0x
2 жыл бұрын
@@tommason4702 oh ok..the right bank..pistons 1,3,5 will be to the rear..left bank..pistons 2,4,6 is up front
@tommason4702
2 жыл бұрын
@@xCHAV0x Thanks a million! This really confused me and I could not get this information anywhere. It's a lot of headache if you order the wrong part. You are my life saver!
How much did you charge for that job?
How long did it take to change the lifter.. Shop hrs???
@xCHAV0x
2 жыл бұрын
I would say 5~6 that’s taking it easy.
How long did it take you to do it
I have the same ticking noise but when we took everything apart all the rockers were fine and now we are lost as to what it could be
@xCHAV0x
3 жыл бұрын
This might be dumb question but did u check the lifters? They are the ones that fail by getting stuck..in my case the lifter got stuck up and caused the rocker to get damaged but if the lifter gets stuck down then the rocker is just gonna be loose causing the noise also inspect the cam lobes
@huntermcauliffe545
3 жыл бұрын
@@xCHAV0x The lobes weren’t damaged and none of the rockers were loose
@xCHAV0x
3 жыл бұрын
There has to be one that is making the noise.. unless ur tapping is coming from the bottom… they might not be too loose but if a lifter is not functioning properly it will tap since is not retracting and expanding as it should
@huntermcauliffe545
3 жыл бұрын
@@xCHAV0x if it’s more underneath what could that be because it’s not knocking like it would if it was a rod problem
@xCHAV0x
3 жыл бұрын
Check your exhaust manifold gaskets they can cause a sort of tick noise..Try using a Stethoscope to pin point the source of the noise.
Did you change it without touching the cam phasers ?
@xCHAV0x
11 ай бұрын
Yes.. timing was not disturbed.
I have the same issue my brotha, how much do you charge to fix the lifters on a 2014 dodge caravan?
@xCHAV0x
2 жыл бұрын
I charge $450 to replace all lifters
@Big-Hit
2 жыл бұрын
Where are you located
@xCHAV0x
2 жыл бұрын
Statesville NC
@caylee3277
2 жыл бұрын
@@xCHAV0x hey I'm getting this sound on a 2015 dodge journey, I'm in Raleigh how far from there are you
@caylee3277
2 жыл бұрын
@@xCHAV0x they are saying lifters and rocker arms
En qué lugar estás tengo ese problema texteame tu dirección estoy en California
How much roughly does it cost to fix rocker arms ? I got 500$ saved and I’m hoping it’s my lifter but just wondering
@xCHAV0x
3 жыл бұрын
At a shop about $1200+ ...an independent mechanic like my self around $250 (if they are honest).. if you want to do it yourself it’s about $130 in parts, that’s including the intake manifold gasket, valve cover gaskets, and rocker..rockers are about $15~$25 each so it’s not bad.
@arnejohnson8623
2 жыл бұрын
It's the labor not the parts that'll get you ... valve lifters and rocker arms are all pretty cheap.
@donsantos7963
Жыл бұрын
You still do this?? Got one like this now
@donsantos7963
Жыл бұрын
@@xCHAV0x You still do this?? Got one like this now close to NC
@xCHAV0x
Жыл бұрын
@@donsantos7963 sorry man just seen this…but yes Im still doing them.
Thanks alot Fiat/Chrysler. Cheap parts.
Does camshaft not need to be come out to replace the rocker arms?
@xCHAV0x
2 жыл бұрын
No u loosen up the cam caps enough to free the rocker arms..if needed turn engine by hand to release tension on rocker arm but spin engine with all caps tightened down.. once the cam lobe is pointing up that will make it easier to remove by loosening a few caps.
@r.a.5625
2 жыл бұрын
@@xCHAV0x Thank you so much
Thanks man!
How long could your drive it with that sound without it blowing up?
@xCHAV0x
2 жыл бұрын
Depend on the severity of the sound but u really don’t wanna risk much time on that… it could go from being a $150~$500 repair to a $1,500~$3,500 repair.
@GoldenArmz910
2 жыл бұрын
@@xCHAV0x mannnn how far are you from fayetteville Nc?
Does driving it with the tick do more damage?
@xCHAV0x
11 ай бұрын
Yea depending on how severe it is it can damage more parts and eventually cause bigger issues.
Thats not a VVT failure....its chinese roller rocker needle bearing failing. The collect in your oil pan also..lol..ask me how i know. Newest revision is AH in the part number
Story of my life
Chavo are you in Texas? I want to pay you to do this to my ram
@xCHAV0x
3 жыл бұрын
I actually just got to TX this weekend but I will only be here this week then I’ll be in NC.. I could do the job this week if u would like I’m located in Tyler tx
@kenbrou2250
3 жыл бұрын
@@xCHAV0x I want to send you my number or something, no private message o. KZread
@junioraviles3192
3 жыл бұрын
@@xCHAV0x im from marshall tx 😎 thnx for postin the video my wifes car has 2 that i know of that are bad. Im currently livin in florida so just gonna get my mechanic to tear down and replace.
Thats a rocker arm bro lifter is underneath lol.
@xCHAV0x
2 жыл бұрын
U don’t say?….the lifter failed causing the rocker to fail.. lifters and rocker arms were replaced.
Will bad lifters give me bad acceleration
@xCHAV0x
2 жыл бұрын
Depending on how damaged it is if it’s to the point where it won’t engage the valve anymore then yes but u would definitely have a loud knocking sound coming from the top end.. look for vacuum leaks that’s more common to cause a bad acceleration
How long did it take you?
@xCHAV0x
Жыл бұрын
About 5~6 hrs depending on how many breaks u take
What is your camera 📷
@xCHAV0x
3 жыл бұрын
Just an IPhone XS Max..
Yo chavo, where are you located ?
@xCHAV0x
3 жыл бұрын
I’m located in Statesville NC
If not fixed,what's gonna happen?
@xCHAV0x
3 жыл бұрын
It will wear dow the cam and eventually break, sending metal pieces into the oil and bigger pieces will get stuck in other valve springs causing them to stay open and causing farther damaged to the engine.. not worth the risk..
@paul91124
3 жыл бұрын
@@xCHAV0x Thanks again,but what cause from breaking? Factory's misasenbury or drove too fast by running engine or use cheap oil? Please let me know thanks.
@xCHAV0x
3 жыл бұрын
Seems to be a manufacturing error because almost every 3.6 from dodge has the same problem..they have revise the engine in these past few year so it not as common on 2017 and up
@paul91124
3 жыл бұрын
@@xCHAV0x Thanks a lot.
We got more noises 😂
How many miles were on that engine?
@xCHAV0x
2 жыл бұрын
127k I believe
Vvt*
Dogo Go Goback
Go back
well, we know you don't like the 3.6's
@xCHAV0x
3 жыл бұрын
Actually I love them..they bring in lots of customers!
@patrickmclaughlin6013
3 жыл бұрын
@@xCHAV0x it seems that way I get the impression you could set up a shop dedicated to just swapping out those cam followers, lifters, phasers, and resealing that plastic thing with the oil cooler, and do very well.