Thanks Doc. Great video. I love tools and thanks to your video I have a good excuse to go do some tool shopping! Thanks again, have a great week.

Great video. I appreciate your spirit of teaching. I absolutely LOVE working on my own vehicles. My Harley is very new to me but I am excited to learn. All your videos are well done and helpful. Thanks, Doc!

Got my service manual for my Road King and my mega tool box. Thanks Doc

Doc, as always THANK YOU BROTHER,! Ride Safe, Ride FOREVER!

Great video Doc! Thank you

Great video Doc! I like the tool cart that you use I think I might get me one for my garage. I think I have most of those tools that I seen in your cart plus other special tools for Harley-Davidson from Jim’s Tools. The manual very important, I like having all three manuals. 1) The basic manual 2) Electrical manual 3) Parts manual The parts manual is very useful it has great parts breakdown views and all of the part numbers (P/N). Look up and write down your own P/N’s before you go to your dealer for parts helps speed things up at the parts counter just make your sure you got the correct P/N for your model from the manual, the manual probably covers several models. If the P/N has been superseded the person at the parts counter will know it. I also have two bike lifts (Dunwell) and several Snap-On torque wrench’s. 🤔 Now if I could only get more room in my garage!

Good video! I agree with 6 point sockets and wrenches.

Great video! New to bikes, and am excited to try and fix things/work on things on my own, but it’s difficult to do that when nobody I know already knows how to work on bikes 😂 this video helped me figure out what I was missing from my toolbox.

Thanks Doc, nice video. Love lots from Philippines.!

I JUST WANT TO SAY I ENJOY YOUR VIDEOS. VERY HELPFUL AS I HAVE OPENED TO DOOR TO DOING MY OWN REPAIR NOWS

I hope my wife doesn't see this vid, I've got her convinced I need about $19,000 worth of tools for my Harleys.

@tylerfj24

5 жыл бұрын

well hell thats just a tool box and a few wrenches and a torque wrench if you go with snap on.

@Grunt49

4 жыл бұрын

That should be PER harley.Plus loctite.

@steveholman5978

4 жыл бұрын

For $19K, instead of working on your old bike, just buy a new one.

@Jgmoya1989

2 жыл бұрын

Same brotha

@jeanettemcfadden228

Жыл бұрын

Hello everyone, kindly check the link on my profile to get all motorcycle parts at affordable prices, can ship anywhere and also available for pickup

Great Video Doc ! I was MMI phoenix 2012

Great you read my mind thanks

love the chrome strion! i have the same one :) cool

the most important: manual service and brain! regards from Brazil!

@flyingdog1498

4 жыл бұрын

Barra do Jucu

I have found that a parts manual in addition to the service manual is very helpful. Not only you have parts numbers but you have a example of the parts layout.

@larrymagee8758

4 ай бұрын

Yes, but they cost big $$$$.

Magnetic trays and pans are a must for hardware and such.....I'm up to 3 of them now :)

Great video. Thanks

@LowCountryHarleyDavidson

2 жыл бұрын

Glad you liked it. Thanks for watching...Doc

Excellent video Doc... now a related scenario. I'm riding my Street glide on a 1,500 mile trip. What tools are must haves in the critical saddle bag space?

Dude, I like your videos, straight to the point. You'd make a great College Professor!

@LowCountryHarleyDavidson

2 жыл бұрын

Thanks...Doc

12 point wrenches spacifcaly and sockets I've noticed I do need for my 18 fxlr brake caliper bolts.

Another GREAT video Doc! What tools are needed for a fork service on a 2005 XLC and a cam change on a 2013 Fat boy lo? Maybe do a video on a fork service? Thanks for everything you do.

@LowCountryHarleyDavidson

5 жыл бұрын

It’s a long list of specialty tools, would really recommend taking it to your local dealership who already has the tools. Otherwise Jim’s the specialty tools you’ll need like a fork seal installer, cam install tools, and more.

Thanks Doc! I'm not as dumb as I thought! Needed to hear 36mm tho!

Hi Doc . great tips . Am new to the Harley davidson scene and and now a new subscriber 👍

@LowCountryHarleyDavidson

2 жыл бұрын

Thanks and welcome..Doc

Thank you

Great video and keep up the good work. What weight dead blow hammer is in your cart and do you recommend that weight for most repairs? Thanks

Thanks for posting. I'm just finishing setting up my new tool cart and your vid is helpful. I've needed an 8mm hex socket for my 2013 brake caliper. It's not a 10mm like the later bikes.

@jime9305

5 жыл бұрын

Although the 8 mm will work, I believe that brake bolt is actually a special 12 spline that's very uncommon

@BrewCityRider

5 жыл бұрын

@@jime9305 @jim e It's just a straight up 8mm hex on mine for whatever reason.

@jime9305

5 жыл бұрын

10-4

My assortment of roto head ratchets are my most used @ home & work, my favorite is 1/4" size with 3/8" anvil. Unfortunately Harley dropped the smaller fender cover from the assecories

First job I had, service manager asked if I had my own tools. Sure, I said. First day in I carried my tools in. He laughed!

Nice “vintage “ craftsman box Doc !

@LowCountryHarleyDavidson

Жыл бұрын

Looks Crafsman but actually a very old Snap-On

Excellent video! I fully realize you cannot go over every tool but is there any way you can take some clear shots of each drawer so we can decipher the tools from the pics. Thanks again, your videos are very informative!

@LowCountryHarleyDavidson

5 жыл бұрын

Fred- can't post the photos on here but took some this morning for you and posted on my page facebook.com/DocHarleyLCHD/

You need your own TV show on motortrend or something!!

Can you make a list of the tools ? I got my first dyna and i want get the right tools

Can you recommend somewhere that I can get an actual hard copy service manual for my streetglide special. It is the last of thd twin cams. There are some online types but you just can not beat a book in your hand, I had haynes and clymer manuals for some of my older bikes but can't seem to find anything for the streetglide special

Let’s hear about some of the specialty tools such as what the hell is used to pull the spark plug boots on the M8plugs under the tank. Or some tech tips/tricks on how to make things easier when working on the bike

I see a lot of Mac Tools!! 👍🏻👍🏻👍🏻

10mm !2 Pt for the Brake Caliper Bolts on 18 XL1200C. Know where I can get a Stubby Flat Head for my Seat Screw?? Came loose the other day. Had to wait until I got home. One small enough to carry in a saddlebag.

What is your opinion on the HD tool set they sell for a good place to start on tools?

Thanks for the video. It was very informative. Can you be a little more specific on the ft lbs/in lbs that are needed (for the torque wrenches)? Also, do you use Loctite in addition to the proper torque specifications?

@LowCountryHarleyDavidson

5 жыл бұрын

Doc here - I have four torque wrenches in my toolbox: For smaller items 5-40 and 30-200 in lbs. For larger 5-100 and 50-250 ft lbs.

@sworndefenders8440

5 жыл бұрын

@@LowCountryHarleyDavidson Thank you!

Thanks Doc! Awesome video... just picked up a service manual for my iron 1200... my question is can I go with the harbor freight tools?

@theone2be33

4 жыл бұрын

Hell no!

@stevesyncox9893

2 жыл бұрын

What he said......

Does that go for twin cams as well as the m8?

are the digital torque wrenches any good I know they cost a lot more. yes right now I own a couple of click ones from Harbour freight

Don't forget the stubby wrenches, Mayhew low clearance 1/4" drive allen wrench set, and 1/4" drive inch lb torque wrench!

Nice video Doc.. Quick question: when torque values are shown (40-45 etc.) do you lean toward the higher number or somewhere in the middle?

@LowCountryHarleyDavidson

5 жыл бұрын

Somewhere in the middle

Is there a specific brand for tools that you go to? I am rebuilding my 2001 Sportster 883 appearance wise, then I may start on the internal cylinder problems. I have not decided yet. I either have to put trust into a repair place that rebuilds “vintage Harley-Davidson”, or do the work myself. A service manual for a 2001 883 is now my next purchase. I will be returning to your various videos.

Bingo! Nice touch putting the owners manual first.

@chefmike8888

5 жыл бұрын

Oh and that magnetic bowl is extremely useful as well. All those little nuts, washers and screws all need a handy place to not get lost

Not sure if anyone has ever told you Doc, but you have a voice for radio haha. Thanks for posting!

@LowCountryHarleyDavidson

Жыл бұрын

Thanks David.....Doc

Loctite, lots of Loctite! BTW when did you attend MMI and what campus? I went to Orlando 97-98

Hey Doc, what size brass drift do you recommend to punch the rear axle out on a touring bike? Should it be small enough to fit in the axle end detent, or a larger one that covers more of the axle end?

@LowCountryHarleyDavidson

5 жыл бұрын

It should be the same size as the inside diameter of the nut.

Thinking about buying a torque wench in inch pound which size drive would you recommend love your video

@LowCountryHarleyDavidson

3 жыл бұрын

I use 1/4” drive torque wrench. Most fasteners that need inch pounds are small. Thanks ~ Doc

dont forget the Molex connector tool, you need a GOOD one, with good steel

I have a 1/2 torque wrench already,, I’m just kinda starting out with HD’s so I see there’s alot of smaller Torque Bits needed, so I ordered a 1/4” Torque wrench up to 150Llbs would that 1/4” be okay for the smaller size torque stuff or should I get a 3/8” Torque Wrench too? Great informational videos, Thanks

@LowCountryHarleyDavidson

2 жыл бұрын

Owning all three is best. The 1/4 handles all the small stuff. The 3/8 is used daily and the 1/2 comes out for Axle, transmission pulley and Compensators...Doc

Doc thank you for your videos , I just purchased a 2019 heritage classic softail 114 , I've been looking for a fairing with a radio / speakers, to replace the windshield..any suggestions. Someone suggested " reckless motorcycle " in Tennessee what do you think

@LowCountryHarleyDavidson

3 жыл бұрын

I truly wish HD would make a detachable fairing with radio for your model. I have no experience with after market fairings with radios. The #1 point to be concerned with is the electrical connections, voltage and amperage draw. The new body control module does not work well with aftermarket electrical add ons. Thanks ~ Doc

Hi doc. What's your thoughts on depinning tools. I'm thinking about buying a electrical depinning tool kit. I seen a video and it looks so easy to remove the wires thanks for your time. Steve Monroe

@LowCountryHarleyDavidson

5 ай бұрын

A “kit” of tools usually covers automotive connectors. And they usually work well with older ( pre 2014) models. The newer the bike the smaller the pins. You only need a few factory supplied tools, the rest you can make with patience….Doc

@stevemonroe1045

5 ай бұрын

@LowCountryHarleyDavidson. Hi again doc. have you ever did a video on depinning electrical construction. Thanks Steve monroe

Hi Doc ! From your years of experience what current brand of tools do you like best for professional mechanics ?

@macxpert3588

3 жыл бұрын

There are a lot of great tools on the market that won't break the bank. Stay off the tool trucks and look for brands like Tekton, Gear Wrench and Kincrome (if you are in Australia or the UK). Even the Harbor Freight Icon tools are good. For screwdrivers the German brands Witte and Wiha are the best. If you work on Japanese bikes then you'll need a JIS cross points (looks like a Phillips but it's not) from Vessel.

Good to know for my 98 fatboy

Don't forget the trailer!

Hey Doc , quick question here. Over the last twenty years I have had numerous front tires replace. Every time they used the same hex nuts and left the original studs in the lower fork leg that holds the axle cap on. I would like to replace those studs. If I use two hex nuts as a jam nut will those studs back out or do I have a really good chance in snapping off the stud in the tapped hole. Any tricks or tips on this process..???

@LowCountryHarleyDavidson

2 жыл бұрын

Depending how old and condition of your bike, better left alone. at least I would apply heat first to the area and then penetrating oil. let the chemicals do their thing and then double nut it. us a bar and not power tools...Doc

Headlamp:)

Hello Doc, thank you for the content I appreciate it. I want to know if it’s possible to install a handle bars from a 2020 Road glide to a 2000 RoadKing classic. Thank you in advance for your reply.

@LowCountryHarleyDavidson

Жыл бұрын

You would have to change the handlebar clamps too....Doc

@juanruiz1260

Жыл бұрын

@@LowCountryHarleyDavidson Hello Doc, thanks for your quick response I appreciate every video you post!!

Do you use a 1/4 driver torque wrench?For screws and such?

@LowCountryHarleyDavidson

6 ай бұрын

Small hardware yes….Doc

Hey doc putting together a tool bag to carry on my 09 ultra classic this is my first harley can you help me out as to what it should carry thanks.

@azizmesned4537

5 жыл бұрын

Mike Martin sr cruztool sells really well made portable toolkits, they have ones made specially for HD, if you want something to keep on your bike, that’s the way to go.

Hey Doc, what tool should I keep on my Harley if I have a break down on the road?

@LowCountryHarleyDavidson

5 ай бұрын

Have you ever heard of Wadsworth Super Deluxe set? Expensive but it has so much. You will still need a few sockets and wrenches…..Doc

Hello Doc; I just buy a Harley Ultra Limited, I will like to install several accessories and because of that I will like to purchase one or two torque wrenches to do the correct job, my question is, what size do you recommend me to buy this tools?, I'm talking about the parameter in ft/pound and in/pound, Thanks for your help!

@LowCountryHarleyDavidson

2 жыл бұрын

This is really your choice. Budget has a lot to do with it. Torque wrenches are expensive. I have 5 year old electronic 3/8 drive ft/lb and they have improved greatly since then. I enjoy my mechanical 1/4 drive inch/pound. I have developed a "feel" with it. I can't recommend cheap tools because this is very important to be good....Doc

What brand and part number for wheel bearing. Removal/ install tool?

@LowCountryHarleyDavidson

4 ай бұрын

Jims is the best. Fast eddy co. Has cool tools. I like his magnets to hold tools together 👍….Doc

looks like it's been awhile since last comment..I'm wondering what tool you use to put on the small hose clamps and remove them. Thanks in advance

@LowCountryHarleyDavidson

2 жыл бұрын

Several are in the box because there are several areas one plier cant reach...Doc

Doc, where can i find a good pair of SMALL snap ring pliers that will fit the small holes in the smaller snap rings that we use on harleys. All i can find around here are pliers that have attachments that are to big for the rings we need. Any help with what you had in the drawer there? (im sure its a 200 dollar snap on but any other ideas)

@LowCountryHarleyDavidson

5 жыл бұрын

Flag down a Cornwell tool truck - they have a Stinger Series brand complete set of snap ring pliers for under $90

@LowCountryHarleyDavidson

5 жыл бұрын

Took some picture this morning - can't post here but took some this morning for you and posted on my page facebook.com/DocHarleyLCHD/

Hey Doc, where is the best place to go to find the service manual for my '96 Fatboy?

@LowCountryHarleyDavidson

4 жыл бұрын

Your local Harley-Davidson dealer. Sometimes a used manual is available on E-Bay. ~ Doc

12 side sockets and star drives! Some type of lift and a chock. 55 gallon drum of Locktite.

@Grunt49

2 жыл бұрын

Lol

Hi Doc, I have always purchased the service manual when i get a new bike. This year however, I purchased a new 2022 lrs, and appears harley isnt selling paper service manuals anymore?

@LowCountryHarleyDavidson

Жыл бұрын

Part # 94000936....Doc

@jeffyoung8047

Жыл бұрын

Fantastic, I just ordered it. Thank you Doc!

What brand is that torque wrench you have that hits 250 ft lbs?

@LowCountryHarleyDavidson

5 жыл бұрын

Snap-On

Hey doc, what’s the best 3/8 digital torque wrench in an buy for my Harley ?

@mitch6969123

2 жыл бұрын

I wanted to know same thing, Best torque wrench for medium price?

Hey Doc what is the tool u used to screw the fork cap bolt? Plmk thx

@LowCountryHarleyDavidson

Жыл бұрын

My tool is from Jims. #1033-TS 1 3/8". Motion Pro also sells Fork tools....Doc

Couldn’t agree more on investing in quality tools. Not saying everything had to be snap on or Mac etc. but cheap tools may cost you more when they break off, round off, etc. I found out the hard way by buying cheap tools

@LowCountryHarleyDavidson

2 жыл бұрын

Thanks for sharing....Doc

Wait! Where can I get the wire rack that your pliers are resting in?

@LowCountryHarleyDavidson

11 ай бұрын

It was sold on one of the tool trucks. I’m sure someone sells the same on the Net…Doc

Id say you are missing a full reach and access kit with torq and Allen's

Does harly offer a program shop manual and parts for a lap top with a diagnostic or code reader ?

@LowCountryHarleyDavidson

2 жыл бұрын

No but I believe Daytona Twin Tech does....Doc

@jefferykirk2322

2 жыл бұрын

@@LowCountryHarleyDavidson what do think about the snap on scan tool ?

Who makes the green pry tool? Thanks

@LowCountryHarleyDavidson

4 жыл бұрын

www.mueller-kueps.com

Where can a service manual be purchased?

@LowCountryHarleyDavidson

Жыл бұрын

Through a dealer. I find good used manuals on E-bay…..Doc

Hi can you please tell me what is your service cart's brand?

@LowCountryHarleyDavidson

3 жыл бұрын

From Snap On. Blue point Series. Affordable. Thanks ~ Doc

Any special tool(s) required for changing spark plugs and wires on M8 touring?

@LowCountryHarleyDavidson

3 жыл бұрын

I have a video that I shared a tool for removing left side plug wires on all models. The right side might need the tank lifted depending on model. Thanks ~ Doc

@sirkingaling3525

3 жыл бұрын

@@LowCountryHarleyDavidson Thank you. Another question, do you recommend 6 or 12-point wrenches and sockets?

@LowCountryHarleyDavidson

3 жыл бұрын

@@sirkingaling3525 In my humble opinion, 12 point is faster but 6 point is stronger. Less likely to come off and round edges. Thanks ~ Doc

@sirkingaling3525

3 жыл бұрын

Low Country Harley-Davidson thank you kindly Doc!

The factory manual for my bike costs $127. Wonder why everyone doesn't have one?

@LowCountryHarleyDavidson

4 ай бұрын

I agree, HD has made it clear. They really don’t want to publish these. They have hinted it won’t be long Dealers won’t be able to purchase. HD wants all techs to use an I pad. I don’t publicly agree….Doc

What these videos lack is the link to some of the products you introduce.

@LowCountryHarleyDavidson

3 жыл бұрын

Kevin there are so many makers of tools with prices that go from affordable to high end. Not every has contact with Snapon, Marco, Cornwell etc. I have views from all over the world. I did not think it was fair to post my choices in a professional shop vs a person working out of a car port that buys used or discount to get the job done. No endorsements for the money either here. The Net is wide open to get the tools you want or need at a price you can afford. For me, I owe I owe so off to work I go. Thanks ~ Doc

As an European I realize now that I'll go shopping for inch' sized tools sooner rather than later.

What's a good scanner

@LowCountryHarleyDavidson

3 жыл бұрын

I use at home the a Harley-Davidson SE tuner, TTS tuner. A friend’s small shop uses Twin Tech products. Thanks ~ Doc

What are good tools?

@LowCountryHarleyDavidson

4 жыл бұрын

Good tools are any tool that helps you fix something. Bad tools are those that break things😆 Thanks ~ Doc

What brand should I go with ?

@LowCountryHarleyDavidson

4 жыл бұрын

Depends on your budget. I choose a tool manufacturer that warranties their tools.

@paulbunyun-xi9by

4 жыл бұрын

@@LowCountryHarleyDavidson Craftsmen

Anyone know what oil weight for a 98 heritage

@darielboyd5007

3 жыл бұрын

20w50

Who makes a good torque wrench ?

@alanwhiteside410

5 жыл бұрын

ALFONSO thegreat All of you Big Name tool dealers Snap-On, Cornwell, MAC and Sturtevant make good torque wrench’s but I’am sure there are some other brands that are good also.

@08StreetGlide

5 жыл бұрын

Proto makes a good wrench, as he said, Snap-on, Mac....etc...

@jacqueskallanian3728

5 жыл бұрын

I picked myself up a Craftsman 1/2" drive at Sears for about $45

@BusterKitten

5 жыл бұрын

for a good one with a life time warranty I chose Husky from Home Depot, been using it for two years and still accurate. Paid less than $80 for the 3/8th.

@sirkingaling3525

3 жыл бұрын

do you guys use 6 or 12-point wrenches and sockets?

And learn how to use a torque wrench. i have the same 1/2 Snap On. read the manual. i have yet to actually see someone set the wrench befor they used it or put it back to 0 after. no jerking the wrench.

What’s the best manual they offer a lot from 10 dollars up 200 hundred what do you recommend and where to get them I’ve got 2014 flhxs

@LowCountryHarleyDavidson

3 жыл бұрын

I can only recommend a Factory Service Manual. It is the Bible for us techs. It was written by the people who build a Harley-Davidson. It is expensive, but worth every dollar. I always keep my eyes open for used manuals to purchase. I don’t have to be the one to take the cellophane off. Thanks ~ Doc

@rickketchumn4458

3 жыл бұрын

I look for one thanks really like all the content you put out it’s help me a lot thanks for all you do

One thing that you showed in your video but didn't mention - Be organized! Having your tools laid out the way you do, in the same place every time, will save you a lot of time. We've all heard "lol I keep losing my 10mm socket!" but if you have your toolbox laid out in an organized fashion, you will know where that 10mm is.

Hi

@LowCountryHarleyDavidson

10 ай бұрын

Welcome….Doc

Links??? Watching does me no good if I have to google sh*t all night. Thanks!

hallå vi har mm system numera när ska ni annpassa er till verkligheten

.

How about me...? I dont have tooL...😆? sometimes i need "HAMMER!" BOOGH..BOOGH...!!! my earing sick😂... By : CICIHARYATI.

@LowCountryHarleyDavidson

2 жыл бұрын

There is always a hammer in the bottom drawer...as a last tool to use..Doc

Is Harley mandating the vaccine?

@LowCountryHarleyDavidson

2 жыл бұрын

This is more than a Harley Service question.....Doc

So to own a $15k-$20k "Harley Davidson" I need another $15k worth of tools to fix it? What a Joke!

@jedihepner

4 жыл бұрын

You need a lot more to work on others

Been getting a few older FLHT's in my metric shop lately. Noticed there's a lot of 12 point bolt heads. Is this just a older model thing or do they use them in the new ones as well? Thanks Doc for all the great videos and vary helpful info!

@LowCountryHarleyDavidson

3 жыл бұрын

It is becoming more common along with Torx instead of Allen’s. Thanks ~ Doc