Bastava ter a chave Allen do tamanho correto, pois a cabeça do parafuso não estava espanada!!!

Torx bit hammered in saves time and works

The idea is nice if you got an old tapper and you prefers to use with this purpose in stead of sharpening it and using it for what is made for. Otherwise you can buy a screw extractor that is a commercial tool made exclusively for this purpose ;)

@Andyspeeder7

Жыл бұрын

Bolt extractors are crap, never in 40yrs have I seen one actually get a tight snapped bolt out , this guy could probably have hammered the square end instead, my preferred extraction tool is a torx bit hammered in

I just finished this exact same repair. I tried heat, torx bit, flat head pounded in, nothing worked. I drilled out the center 4mm and was able to use a bolt extractor.

Cerdas,untuk keadaan darurat,tapi lebih mudah pakei screw ekstrakor

Use what you have and come up with a way to make it work. Not the way I would have done it but good thinking 👍well done

Hammering in a good quality star bit gives the same result 👍

If it is a brake cylinder sliding iron column rusty stuck cannot be remove Is there any way to remove it ?

Waaah...kalo saya sih sayang sama handtapnya bang...

Mantap om ilmunya

👍nice Idee

GOOD👍👍👍

Tighten up the vice on work bench, it is loose.

wajib beli tab dulu....!😁🙏

Lebih aman stelah di bor pake mata obeng getok, di bikin segi empat tapi pjokan sudut pesegi empatnya di bikin tajam, malah lebih kuat, maaf hanya saling berbagi

Its a waste of tapping tools instead on other way & normally l use star socket hex to open the stud coz its much easier & save a lot of time rather than grinding the tools if u all dont believe u all can try use it or slightly bigger in size of the star hex

Buka sendiri skrang mh bos ?

Itu kalau kategori mudah, kalau macetnya udah parah, gak bisa diapa apain tetep akhirnya dibor terus di tap ulang.

dobre to :D

👍🏻👍🏻👍🏻

"Torx" можно забить.нагреть,wd-40. Ну а потом и инструмент портить😄

Kalo yg bener bener keras itu mata taf bisa patah bosss😊

整個白眼到翻過去

Красавчик!!!!

Sao ko sit miếng nhớt hay rp7 vô

tukang las beeres jhon... 10K slsai

@kenaja7863

Жыл бұрын

Kalau gak bisa kebuka gimana ngebor nya baut di las akan megeras besi

@werkudoropandowo

Жыл бұрын

@@kenaja7863 bawa sini. biar kamu tahu

タップは折れやすいから止めた方が良い。

qua OK

👋👋👋👋👋👋👋👍👍👍👍👍💯

baut yang susah dibuka karat harus ditetesin VPC dibagian karatnya 😆😆😆😆😆

и чего? Этому способу более 50 лет. Ты видимо сам много чего не знаешь.

di bawa ke tukang las beres

Parei de assistir nos primeiros 1.47 minutos, uma mancada cade a chave correta.

Торксы есть для таких издевательств. А сломается метчик ну это следующее видео.

Я сломал мечик в болту остался кусок. Спасибо канеш, но не очень.

@lakhtaG64

Жыл бұрын

я обычно такую шляпу, выкручиваю битой звёздочкой. есть мелкая звездочка и крупная, вот крупной самое то. шестигранники она крутит на раз👍🏻

Lah kesuen

Hmmmmm

Ну что ж так нудно?

не культурно инструмент портить.

It will make you dumber to break down a machine in order to extract a bad screw