DJI Phantom FC 40 with brushless gimbal , test flight

Фильм және анимация

DJI Phantom FC 40 with CNC Brushless Gimbal (china brushless gimbal) and original FC 40 camera.
More videos and news on:
snimanjeizvazduha.blogspot.com/
SimpleBGC 2.2b2 my setting for FC 40:
Basic:
Roll P 11 I 0,1 D 6 Roll Power 100
Pitch P 7 I 0,1 D 6 Pitch Power 60
Advance:
Gyro Trust 100
PWM frequency: Low (Noisy)
Follow mode
disabled all
Camera mounted on left side of gimbal, as much as possible to be balanced with motor by roll axis
But it need more settings, curently I have no idea what to I improve in settings for Pitch ?
with Roll maybe only to add more power to motor

Пікірлер: 8

  • @mssippijim
    @mssippijim7 жыл бұрын

    FC40 is without a doubt the best quality 720p video I've seen from a quad. I think it actually looks better than a lot of cheap 1080 cameras.

  • @DjordjeJojkic
    @DjordjeJojkic10 жыл бұрын

    OŠ Pavle Savić , Mirijevo - Beograd Test brushless gimbal-a

  • @iKokomo
    @iKokomo9 жыл бұрын

    I have a couple questions :) 1. How did you install the FC40 to this Gimbal? and 2. What settings did you use on the Simple BGC Utility to help balance the camera? Thanks

  • @DjordjeJojkic

    @DjordjeJojkic

    9 жыл бұрын

    1. Just mount on Phantom. I use two cuted wires that you can see on phantom, for power source, and connect with only one signal wires from gimbal to Naza controller inside phantom for pitch function (also you will need to install leveler to rc controller) You can find tutorial videos on you tube for this 2. Settings for BGC that I use, you can find here (it is my post): www.djiguys.com/Forum/viewtopic.php?f=42&t=4228 Most important that at the end, I lost my nerves, because it is cheap, but not good solution, I had many jello started with light wind , and at the end I buy used Zenmuse 2 Axis, upgrade FC 40 board and buy GoPro. After that all is excelent, expect that I wish 3 axis gimbal :P If you still want to try, CNC gimbal and FC 40 camera, maybe is better to try factory GoPro settings in CNC gimbal, and add more weight and balance to mounted FC 40 camera, then to try setting BGC, because metal gimbal is is not balanced for low weight FC 40 camera

  • @budlightyear8497
    @budlightyear84979 жыл бұрын

    Will a gopro hero 2 also work. And are u able to tilt the cam. Im using a phaton dji fc40 and not sure how to connect or what gimbal to use..please advice

  • @DjordjeJojkic

    @DjordjeJojkic

    9 жыл бұрын

    This brushless gimbal, as most of gimbals came pre set for GoPro 3/3+ . For other cameras, this gimbal that I use, must be set up by user. I dont try to use it with GoPro 2, must to ask someone else To enable tilt camera by RC, you must connect gimbal with signal wire directly to Naza conntroler in quad (you must to open Phantom, it is not hard, as it looks ) :) , after that do calibration in Naza Assistent software, and of course to buy leveler for radio control device (transmiter), or use screwdriver for test :) 3.bp.blogspot.com/-SonJePEYc9Q/U352EYsefjI/AAAAAAAAAfY/SdY66TB2vcA/s1600/fc40-front.jpg

Келесі