========UPDATE 20 Februari 2024========= - implementasi PID controller - high speed PWM =========UPDATE 4 Februari 2024========= New Firmware and Schematic - perbaikan pada rotary encoder - perubahan wiring rotary encoder - penambahan fitur fast dan slow rotation rotary encoder jadi ketika diputer cepat suhu bertambah/berkurang 10, jika lambat bertambah / berkurang 1. yaaa lumayan biar precise ampe 1 derajat :v

@muhammadalansyah_ft2581

3 ай бұрын

codenya gabisa dibuka bang

@RecehDIY

3 ай бұрын

@@muhammadalansyah_ft2581 di saya bisa kok pak, viewers yg lain juga bisa kok

@satreaaji

2 ай бұрын

Makasih pak, btw nama connector untuk soldernya apa ya pak? Apa kah tipe DIN?

@RecehDIY

2 ай бұрын

@@satreaaji aviation plug pak, atau konektor CB

@satreaaji

2 ай бұрын

@@RecehDIY makasih pak

gacor pakk, baru nemu channel ini, jiwa DIY langsung meronta ronta 😂

@RecehDIY

7 күн бұрын

kalo gacor subs dulu dong pak :D

auto susbrek pak..suka penyampaianya dan mudah d pahami...semangat pak bikin turornya...💪👍👍

Wah ini nih DIY next level

Keren hasilnya rapi 👍👍

Auto subcribe Nyalakan lonceng ini mah

Joos dah pak sy subrek 👍😊

terbaik mas. keep it up

Isi daging, auto subrek

sukses selalu terimakasih infonya, semoga ilmunya berkah Om. Mantaaaapp salam kenal Om.

@RecehDIY

3 ай бұрын

siap pak thanks udah mampir

kreeen broo.. mantaapppp

@RecehDIY

Ай бұрын

gas om,bikin

Orang indo harus banyak bikin konten kek gini biar gak kalah ama prindapan

auto suskreb

Smangat berkarya bang....gasken....

@RecehDIY

3 ай бұрын

thanks dah mampir pak gas

keren2, saya suka penyampaiannya, tidak berbelit2, auto subs

@RecehDIY

3 ай бұрын

siap pak. thanks udah mampir

@droidinsides

3 ай бұрын

boleh minta list barang yang harus di beli semuanya bang, maklum pemula takut salah beli@@RecehDIY

@RecehDIY

3 ай бұрын

@@droidinsides di schematic jelas semua pak bahan yg dibeli. paling female ama male header nya doang yg ga ada di schematic. schematic nya juga friendly kok untuk pemula

@droidinsides

3 ай бұрын

bagi saya belum bisa memahami bang, mau blajar rakit beerasa masih kurang detail @@RecehDIY

@RecehDIY

3 ай бұрын

@@droidinsides wah kalo gitu mohon maaf pak, minimal belajar yg basic electronic aja dulu, misal kaya fungsi resistor apa, pengaplikasiannya gmn. opamp cara kerja nya gmn, gitu pak

mantap pak,,, coba bikin yang pake node mcu pak,,

kerreeeen

terimakasih banyak pak. saya jdi pengen bikin juganih hahaha. mumpung ada dana mau beli solder station

@RecehDIY

10 күн бұрын

bikin dulu aja pak. anti gagal sih seharusnya. kalo ada trouble tinggal tanya dimari

keren pak

luar biasa pak

@dewaamor6640

22 сағат бұрын

Idola saya juga ini Pak @DanyDwiPrayitno dlm belajar elektronika,...

Keren Pak, Auto Subs sama ijin ninggalin jejak komen ya pak, santuy bet ngejelasinya , wajib di coba nih 😀

@RecehDIY

3 ай бұрын

gaskeun coba pak. enteng lah ini.

Mantab pak, jadi pengen ikut buat, sub dulu ah 🎉

@RecehDIY

3 ай бұрын

gas pak buat 1 🤩 siapa tau ada ide lebih menarik

Ditunggu DIY SOLDER buat mata solder c210 atau t220 bang, versi murah nya 🙏🙏🙏

Sudah di subrek👍

@RecehDIY

3 ай бұрын

thanks pak 🔥

keren bingit

@RecehDIY

3 ай бұрын

thanks udah mampir pak

Keren pak. Solder saya masih jadul

@RecehDIY

3 ай бұрын

ayo upgrade pak

@PujiSERVISELEKTRONIK

3 ай бұрын

@@RecehDIY iya pak pengen upgrade biar makin nyes...

Nyimak bang

Auto subrek 👍👍👍

@RecehDIY

3 ай бұрын

shaapapp thanks udah mampir pak

Lanjutkan om dengan komentator agak ngeselin 😂 Inspiring om 👍

Mantap

Solder station digital udah punya 2, jarang dipakai pula, tapi entah kenapa kalau lihat DIY seperti ini malah pingin bikin

@RecehDIY

3 ай бұрын

jiwa diy nya meronta2 ya pak? 😅

@muhaiminulaziz8307

3 ай бұрын

@@RecehDIY betul sekali pak, ada rasa senang bisa beli alat baru, tapi DIY membuat rasa bahagia dan rasa puas secara bersamaan (kalau berhasil) 😁

@user-qj1mx7mg2q

3 ай бұрын

semua diyer gitu mass, sy jugaa

@muhaiminulaziz8307

3 ай бұрын

@@user-qj1mx7mg2q saya kira sayanya yang terlalu kemaruk, ternyata bukan saya saja

@REVOLSAMI

3 ай бұрын

Tipikal jiwa laki

Ga nyesel ue subrek Lo bang👏👏👏.....di tunggu yg T12 nya bang🙏🙏🙏

@RecehDIY

3 ай бұрын

siap pak next dah ane coba bikinin yg bisa 9xx ama T12

@rohmatuzaman8553

3 ай бұрын

@@RecehDIY di tunggu video tutorial nya ya bang, terimakasih 🙏🙏💪💪🇮🇩🇮🇩

Manteb

Keren pak, sub dulu diy nya belakangan 😂

@RecehDIY

3 ай бұрын

aman pak diy kita yg enteng2 kok

keren pak... kreatif 👍.. ada jempolnya plus suara gak asing (kayak si nexlevel)😂😂

@RecehDIY

3 ай бұрын

selingan dikit2 pak. btw thx udah mampir pak

@rokrs

3 ай бұрын

@@RecehDIY jadi pengen coba bikin nih... menginspirasi sekali.... 👍

keren banget ini jd pengen bikin. request solder c210 / c115 om.

@RecehDIY

3 ай бұрын

gas pak bikin 1 gampang ini mah c series ama t12 nyusul ya pak cari duit nya dulu

@kentangCH157

3 ай бұрын

@@RecehDIY inpo kontak nya donk om. 😁

gokill nih

@RecehDIY

3 ай бұрын

thanks udah mampir paj

Aku suka

Mantaap 👍👍👍

@RecehDIY

3 ай бұрын

thanks udah mampir pak

Auto subscribe Kerennn om.. Link shopnya om yg udah jadi 😊

@RecehDIY

3 ай бұрын

ntar deh pak tunggu cetak pcb yg proper

Maaf mas saran aja bagi yang mau coba kalo misal ada yang error: - code tidak bisa dibuka bisa open with note dulu, abis tu code di copas ke arduino IDE - exit status 1 'class LiquidCrystal_I2C' has no member named 'init' lcd.init() diganti jadi lcd.begin()

lapor pak solder station sudah sukses di buat.. tinggal bikin bok nya ja. makasi pak.., di tunggu yg T12 + C210 nya 😁

@RecehDIY

2 ай бұрын

aman berarti ya pak? mantep 👍👍👍

@defrzn939

2 ай бұрын

@@RecehDIY aman pak.., pas rakit gak ada kendala berarti cuman di awal termokopel kebalik ja..., saya ada baca2 di komennya harus pakai mosfet tipe IRL , tpi saya pakai yg IRF pak.., bedanya apa pak..?

@RecehDIY

2 ай бұрын

@@defrzn939 beda RDSon (tegangan kerja) nya pak. IRL itu mosfet logic, biasanya temenan ama micro controller, tegangan kerja nya di 5 volt. kalo mosfet biasa rdson nya di 10 volt++. coba aja pegang mosfet nya pas lg kerja pak, pasti panas 🤣

@defrzn939

Ай бұрын

@@RecehDIY di saya kok malah gak ada panas2 nya sama sekali pak.. tanpa heatsink lgi.. 😂 dah di pake kerja beberapa hari.., mungkin karna fet kw kali pak.. soalnya beberapa kali coba pasangin ke power amplifier mobil sbagai komponen pengganti di gaber dikit tu fet langsung ambyar.. 😂

@RecehDIY

Ай бұрын

@@defrzn939 logic level biasa nya lebih mahal pak dr fet biasa 😅 ya mungkin krn 1 ampere kali ya beban nya. tp terakhir saya coba pake irf540n panas sih, tp masih bisa di sentuh

Saya punya modul spt ini termasuk skematik udh masuk ke easyeda, tinggal cetak pcb ma rakit lagi maless banget 😂😂😂

sumpah mantep bener bang. btw zoyi zt102a saya udah saya upgrade pake batre iphone sma charger type c. ya ga jauh beda sma punya abang lah. semangat terus bang

@RecehDIY

3 ай бұрын

widih, mantep pak. hati2 ya pak, multimeter kondisi off juga makan baterai loh kalo ga sesuai instruksi video 😄

@HajarTech

3 ай бұрын

@@RecehDIY ohh kasih tutornya dong bang buat zoyi zt102a atau harus pake apa aja. saya cuma modul charger type c doang

@RecehDIY

3 ай бұрын

walah, ga pake regulator 3.3 volt ya? langsung direct dari baterai iphone nya gitu?

@HajarTech

3 ай бұрын

@@RecehDIY iya om, bakal gmna jadinya

@RecehDIY

3 ай бұрын

@@HajarTech ga tau pak, mudah2an awet dah zoyi nya 😅 soalnya saya ga ada lihat ic regulator di sekitaran PCB

Request dong gabungin 3 judul jadi 1 - solder station - power suplai/ mbr - solder uap

@RecehDIY

3 ай бұрын

maksudnya gmn pak? kurang paham saya. dalam 1 video ngebahas 3 item tersebut, atau bikin 1 tools yg bisa 3 fungsi diatas?

@rijalnasrulsabillaha.md.t6794

3 ай бұрын

@@RecehDIY bikin 1 tools 3 fungsi

@kentangCH157

3 ай бұрын

bikin aja satu2 trus di gandengin di lakban gitu kwkwkwkw

@rijalnasrulsabillaha.md.t6794

3 ай бұрын

@@kentangCH157 ntar penuh mejanya cuma buat 3 tools 3 box 🤭

@gurisan1779

3 ай бұрын

nah mungkin itu pak...1 tools 3 fungsi@@RecehDIY

Mantap pak, nah nanti yang ini di upgrade lagi jadi T12 ato jbc model

@RecehDIY

3 ай бұрын

bisa aja pak,base model nya udah ada tinggal ganti pcb nya doang kok. untuk sementara yg murah2 aja dulu 😅

@fajarsan329

3 ай бұрын

@@RecehDIYAh bisa aje niih, tinggal tambah dikit lagi padahal 😀yo wis semoga tambah sukses channelnya, ditunggu video upgrade nya

@RecehDIY

3 ай бұрын

@@fajarsan329 eh salah, maksud saya yg mudah2 aja dulu 😅 siap pak, ditunggu aja ya

Ikut beli

Kereenn ini mah 🔥🔥, walaupun bukan anak elektro kata2 dari saya emang blower doang yg bisa di adjustbale dan ada screen monitornya 😂

@RecehDIY

3 ай бұрын

cot 🤣

Pak request bikin kaya gini tapi di gabung sama solder uap, jadi kaya 2 in 1

@RecehDIY

3 ай бұрын

bagus nya sih jgn digabung2 pak,ntar semisal blower rusak, solder nya malah ga bisa dipake krn lg di perbaiki 😅

@fiwal150

3 ай бұрын

@@RecehDIY kalo untuk bikin modul blower ya bisa GK pak? Modul yang auto ketika suhu sudah mencapai yang kita inginkan?

@RecehDIY

3 ай бұрын

@@fiwal150 enteng lah pak. ditunggu aja yes

Solder masda cukup. Panasnya cepat.

@RecehDIY

3 ай бұрын

sekarang bukan siapa cepet2an panas pak. ada komponen tertentu yg kalo di solder minta nya max di 270°. masda bisa? 😅

@soniwibisono4662

3 ай бұрын

@@RecehDIY bisa

@kapuyuaklegend9883

3 ай бұрын

@@soniwibisono4662 bisa apanya..? coba solder motherboard komputer / laptop dijamin pengen banting tu solder.. 😂

bre, bikin tutor pake solder t210 plus auto sleep

Pak buat solder station yang versi T12 pakai arduino nano dan pakai LCD graphik

@RecehDIY

Ай бұрын

sabar ya pak ini lg on progress

@rasyanurramadhan1031

Ай бұрын

Siap pak

request solder uap pakai led 7 segment mas bro

@RecehDIY

3 ай бұрын

ditunggu aja ya pak

wow cangih banget pak nyesel saya import modul kit t12 kalo di sini ada

@RecehDIY

3 ай бұрын

beda lah pak ini mah gak secanggih modul t12 yg impor. ntar deh saya bikin yg versi t12, baru deh nyesel nya dikeluarin 🤣

Nyimak pk tipe solder t12 gan

@RecehDIY

3 ай бұрын

t12 ga asik om, udah ada modul nya :D

Next project buat hot blower pak.

@RecehDIY

3 ай бұрын

aman pak ini tinggal mikirin casing yg cocok aja

@jordanmahadewa7684

3 ай бұрын

ditunggu pak videonyaa​@@RecehDIY

Request bang, bikin preheater universal berbasis arduino

@RecehDIY

10 күн бұрын

sama aja prinsip nya pak. tinggal nyesuaiin aja kalo misal arus dc pake mosfet, kalo ac kudu pake opto ama triac

diy soldyer ang tipe c210 bang

@RecehDIY

3 ай бұрын

c210 ribet, mahal lagi. mending t12 sih kalo kata saya om

Itu mata soldernya di ganti punyak e t12 bisa?

saya yang jarang pegang solder pun pengen setelah nonton video ini😭

@RecehDIY

3 ай бұрын

ayo pak bikin 1 buat di pajang aja udah 😄

Request Buat T12 atau C210 kang hhe

@RecehDIY

2 ай бұрын

ini tinggal nunggu case nya pak

@Queencell18

2 ай бұрын

@@RecehDIY thank uuuu ditunggu kang

sudah subscribe 👍 klo dijual mau bang

Receh nya pake golden ini mahh 🎉

@RecehDIY

3 ай бұрын

mwehehe makasih pak thanks juga udah mampir

Pak buat pcbnya di pcbway

Bang buat station solder buat solder uap nanti tak supberk😂

@RecehDIY

3 ай бұрын

loh he subrek dulu dong pak tenang, pasti dibuat kok 🤣

Nice build, but why did you stick to deprecated heater technology?

@RecehDIY

3 ай бұрын

it's cheap and easy to build. most of us (indonesians) still use it and this is just an introduction for those who want to get into electronics 😅

@deterdamel7380

3 ай бұрын

@@RecehDIY Yes, that's possible and an important point. We (people) in the rich counties can spend more coins on unimportant extras and at the end of the day we will not even make a smarter solution.

Boleh di beli hasil karya nya ? VERRY COOL

Itu mata solder nya ganti t12 bisa?

Bang, tolong buatin tutor buat solder uap pake arduino bang. Tapi pake 7 segment

@RecehDIY

3 ай бұрын

ada sih ide nya 7 segment tp ga pake arduino. cuma ngandelin opamp aja

@Zen2ncd

3 ай бұрын

Kalo semisalnya opamp diganti max6675 bisa gak bang? Kan sensor suhu di solder ini sesama thermocouple. Atau bisa ngandelin adc-nya esp 32?

@RecehDIY

3 ай бұрын

@@Zen2ncd ngapain pake max6675 kalo opamp jauh lebih murah? 😅 gunanya opamp atau max6675 kan buat amplify tegangan dari thermocouple yg kecil banget biar bisa di baca adc. kalo direct dari thermocouple ya ga bisa dong pak 😅

Ini buat solder t12 bisa pak?

Hallo Bang. Kalo link pembelian yang suda dirakit ada ngga Bang?

bikin yg buat gagang c210 bang

@RecehDIY

3 ай бұрын

c210 mahal pak bahan2 nya. mudah2an besok bisa bikin deh

sori pak tadi pas subskreb mau pencet like malah dislike, tapi not bed, udah saya pencet tombol like nya lagi pak, 2x

@RecehDIY

3 ай бұрын

ealah pak jujur amat selow pak kita gas next video biar betah

Assalamualikum mas ,tolong dijawab ya mas. Mas apakah beli modul arduino sama lcd atmega harus di diisi file lagi? Apa beli tingal rakit jadi?

@RecehDIY

Ай бұрын

lcd tinggal colok pak. kalo arduino tinggal colok ke pc, file nya udah ada di deskripsi pak.

Gan request donk buat yg solder nya bukan thermocouple Makanya ga kelar² Sepertinya gagang solder saya pakai thermoresistor deh Atau ada cara mastiin nya gan apakah gagang solder nya pakai type sensor apa ?? Thanks

@RecehDIY

10 күн бұрын

cara mastiin nya ukur pake multimeter pak. kalo ketika di panasin ada keluar tegangan berarti thermocouple

@ipunkkurabalap9958

9 күн бұрын

@@RecehDIY bener udah di pastiin Udah saya beliin solder yg thermocouple Skrng case nya suhu bisa naik Setting suhu 120derajat Suhu pembacaan 50derajat tapi aktual solder udah 100 derajat lebih info setting nya donk Maaf merepotkan

Setelah menonton video ini sepertinya saya lebih tertarik membeli buatan abg ini dari pada buatnya sendiri 😂

@RecehDIY

3 ай бұрын

jgn pak esensi DIY nya ga ada dong bahan2 tinggal download kok pak

@elvysermarlynsoepriyanto395

3 ай бұрын

Gpp kah bang, kita jg mau pesen nih ga pake adaptor gpp kita punya tuh adaptor,ok ya bang pesen

@elvysermarlynsoepriyanto395

3 ай бұрын

Plisss lah

@RecehDIY

3 ай бұрын

@@elvysermarlynsoepriyanto395 nanti kita cetak pcb nya dulu pak

@elvysermarlynsoepriyanto395

3 ай бұрын

Siap request ya bang n dikisaran brp gt, sy butuh bngt untuk perdinamoan

Bang req smart multi tester yg konek ke pc😅

@RecehDIY

3 ай бұрын

req apa nih? review atau bikin? 😅

@user-ut1xl8jp9n

3 ай бұрын

@@RecehDIY bikin nya bang 😅

@RecehDIY

3 ай бұрын

sepertinya ribet pak. udah ga receh lg itu namanya 😅

@user-ut1xl8jp9n

3 ай бұрын

@@RecehDIY nampak nya harus ada bisik bisik tetangga 😁

izin sedot schemanya pak

@RecehDIY

3 ай бұрын

gas pak jgn ragu2 😅

bu projeyi yaptım ama termometreyi kalibre etmeme rağmen ısıda bir hata var

@RecehDIY

2 ай бұрын

You will not see any changes on the Arduino screen when you rotate the calibration trimmer. it will only occur at the value on the external thermometer

izin tanya pak, klw pakai charger 12 v 1 amper apa pengaruhnya pak? termakasih

@RecehDIY

3 ай бұрын

belum nyoba sih pak. kalo dihitung dr hambatan elemen yg cuma 15ohm trus juga mosfet yg ga tersaturasi sempurna, ya arus yg masuk paling cuma 600 s.d 700 mA. konsekuensi nya apa? panas jd lama, atau worst case nya ga bisa sampe ke suhu yg agak tinggian.

Bang buat yg solder uap dounk

@RecehDIY

3 ай бұрын

aman pak. ini lg mikirin casing nya yg keren pake apa

@ikwanjovanovic3596

3 ай бұрын

@@RecehDIY widih .. Ditunggu bos .. Mantap

Kak mau tanya apa bisa dibuat portable/Batrai Ces pak

@RecehDIY

2 ай бұрын

bisa pak recommend pake batre bor cordless yg 21 volt

you can convert hakko 936 analog to digital use arduino?

@RecehDIY

2 ай бұрын

ofcourse it can be done as long as the heater not in series with thermocouple. afaik all 9xx series are using that method

@BdThuan

2 ай бұрын

@@RecehDIY I made a separate op-amp circuit and connected it to the thermocouple of the welding hand 936, using an arduino to read the voltage from the heat sensor of the welding hand, but the temperature value is not accurate, the impedance of the heat sensor 936 is about 56 ohms. i just want to display temperature value by LCD instead of analog like 936, no need for other functions. moreover i use arduino LGT8F328P-LQFP32 MiniEVB, ,it is similar to nano but its ADC is 12 bit, instead 10 bits like nano. If you have time, can you make a video tutorial? Thank you very much

@RecehDIY

2 ай бұрын

@@BdThuan are you using the schematic that i made? first, you have to make sure what kind of heat sensor used in the iron. if it's a thermistor, then you need to provide a pull up resistor to the sensor (for example 470ohm). google it for more details. keyword : NTC to ADC

Bang apakah bisa pakai gagang solder 907D

@RecehDIY

Ай бұрын

ga bisa kayanya bang ga ada thermocouple nya itu

#ask seumpama ini saya konekan dengan solder goot tq-77, apa support ya bro??

@RecehDIY

2 ай бұрын

ga bisa pak. solder model gitu biasanya ga pake thermocouple. dan butuh high voltage buat nge drive elemen heater nya. saran saya, udah dibuang aja pak. bikin model begini. atau tunggu video saya ttg solder T12

Pak itu komponen yang setelah resistor 200r thermistor ya? Yang warna putih

@RecehDIY

21 күн бұрын

led itu pak ga ada thermistor disini lagian kalaupun itu thermistor ga mungkin di pcb pak, pastinya didalam elemen solder 😅

@yudhajufrie5605

21 күн бұрын

@@RecehDIY hehhee siap pak terima kasih

gagang hk 936 itu thermocouple atau thermistor pak ya?

@RecehDIY

7 күн бұрын

diukur aja pak pake multimeter kalo bisa ngeluarin tegangan ketika dipanasin artinya pake thermocouple

Hello, have it a standby mode ? I mean when i put it to the stand after 2-3 Minutes its goes cool down a little bit to 200 grad for 3-5 Minutes ? Or have it when i set it to 350 grad it stays from beginning to shutdown constantly ? It is very good, when its have a standby mode : (

@RecehDIY

Ай бұрын

there is no point for adding a standby mode or auto shutdown on 9xx series. the problem is, the heating time takes forever, not as fast as T12 or C series.

@user-bw5hk5nb3k

Ай бұрын

But for me i think it is not a problem to wait, constantl hot meaning faster ceramic heatelements die and its must replaced ? No chance to add a sleep mode ? : (

@RecehDIY

Ай бұрын

@@user-bw5hk5nb3k you can use any digital pin as input pull up, then add some millis when digital pin get LOW. you need to utilize a reed switch to do that. easy, isnt it? 🤣 but think again, when you put the handle on its stand, let's say 2 minutes sleep time, the station entered sleep mode, temperature stay somewhre at 200°. then you need to do a soldering ASAP, you pull the handle out of the stand, and wait the element reach the temp you needed. it sounds like, wtf? you hold the handle on your hand while waiting the element to heat up? 🥲 thats why i put the "OFF" mode on it. it's just a matyer of habit 😅

@user-bw5hk5nb3k

Ай бұрын

I don't need speed when heating up, my Weller 1983 model was hell and I always had patience :( How do I do it so that it switches to sleep mode, that sounds like coding to me, unfortunately I can't code :( exactly 200 degrees and in sleep mode, for example with the corn cob weller RT edition. i will build that soo lovely but i havent a sleep mode here 😞

Mau tanya donk, kalau di bikin buat solder uap bisa ga yah

@RecehDIY

3 ай бұрын

ditunggu ya pak, next bakalan ada solder uap kok

Kaki tengah IRLZ44N ke soket itu dioda zener ukuran berapa ya om

@RecehDIY

3 ай бұрын

bukan zener, dioda biasa pak, kalo bisa yang fast . bebas mau brp minimal 500mA

@henryriasman

3 ай бұрын

@@RecehDIY detail dioda rekomendasinya type berapa ya dgn volt segitu ...terimakasih responnya sukses selalu

@RecehDIY

3 ай бұрын

@@henryriasman 1n4148 bisa 4007 juga gpp

@henryriasman

3 ай бұрын

terima kasih kak..sukses selalu

mau tanya om, apakah displaynya jika di ganti dengan oled bisa?

@RecehDIY

2 ай бұрын

bisa pak tinggal ubah beberapa line aja

O iya, untuk step down nya bisa pake step down biasa atau harus mini step down?

@RecehDIY

3 ай бұрын

bebas pak saya pake mini stepdown biar kecil aja sih lagian konsumsi arus nya kecil kok

mohon di koreksi klo salah itu pin sda clk yg masuk di lcd salah bang terbalik

@RecehDIY

3 ай бұрын

awoakwoakwoak iya pak kebalik. nanti saya revisi

Pengen bikin tapi gk bisa caranya... Lihat skema bingung sendiri wkwkw

@RecehDIY

3 ай бұрын

padahal schematic udah berbentuk wiring diagram loh pak. udah pake gambar komponen, bukan symbol lg

@vick_garage

3 ай бұрын

@@RecehDIY tak download gk bisa di buka di HP soalnya... Hpnya jelek... Nantilah tak coba e pakek komputer...

mas, itu di pin D12 setelah resistor 200 ohm itu apa ya?

@RecehDIY

7 күн бұрын

LED SMD pak

@zakiarrayyan5132

7 күн бұрын

@@RecehDIY oiya terimakasih, baru saya lihat di code nya pin 12 LED hehee

Bang bikin solder uap pake mikrokontroler arduino 😅

@RecehDIY

3 ай бұрын

aman pak, ini lg mikirin casing nya yg agak nyeleneh 🤣

@raflynf7326

3 ай бұрын

@@RecehDIY bikin pake akrilik lebih menarik mungkin😂

@RecehDIY

3 ай бұрын

@@raflynf7326 kalo kebuka2 kaya station yg ini ngerih pak, krn direct langsung ke PLN ☠️

@raflynf7326

3 ай бұрын

@@RecehDIY siapp bng ditunggu upload video nya

Pake gagang solder 936 bisa bisa ngga pak. Atau harus ngerubah rangkaian dulu, sama kita" bisa nyentuh 450°C ngga ya pak. Soalnya gagang soldernya murah pak 30 ribuan wkwkw, tapi itu saya ngga tau pakenya thermocouple atau thermistor

@RecehDIY

Ай бұрын

936 biasanya pake thermocouple pak seharusnya bisa sih dengan catatan tegangan yg digunakan 24 volt

@danuaf3806

Ай бұрын

@@RecehDIY oke pak makasih pencerahannya. Otw bikin nih

Buat controler solder c210 bisa pak?

@RecehDIY

3 ай бұрын

bisa pak duit nya yg belum bisa 😅

termometre neden minimum 28 dereceden başlıyor?

@RecehDIY

2 ай бұрын

you can change it on line 34 (minTemp) and line 36 (minADC) in the sketch that I uploaded. all you have to do is measure the ambient temperature with an external thermometer, and measure the ADC on analog pin 0. for example, your ambient temperature reads around 30° on an external thermometer, and the ADC value on pin A0 is around 5 or 7, you just need to enter that value in the sketch.

@digerioteki6296

2 ай бұрын

teşekkür ederim, bunu deneyip size bilgi vereceğim.

pak mau tanya.. digambar pin rotary CLK=2 DT=3 SW=4 keterangan kodingnya beda Pins 2 (DT), 3 (CLK), 4 (SW) masih sementara rakit, semoga berhasil

@RecehDIY

2 ай бұрын

dirakit aja dulu pak sesuai skematik. ntar kalo putaran rotary nya kebalik, tinggal diubah/dibalik aja itu clk ama dt nya.

@MsMus86

2 ай бұрын

@@RecehDIY siap pak.. Ngaruhnya cuma diputarn yg kebalik ya ternyata

@RecehDIY

2 ай бұрын

@@MsMus86 yes betul pak, asal jgn sw nya aja yg dibolak balik 😅