The absolute most widow maker way to compress a spring. Don’t do this at your hacienda…
Жүктеу.....
Пікірлер: 39
@DrAppleCrispies Жыл бұрын
Safer than the clamps I've seen people using, I've watched alot of these jump out of cages but never had an issue with strapping them.
@BellyUpFish
Жыл бұрын
Seems like it’s definitely safer than the standard Autozone grade spring compressor.
@TechTimeElectronics
5 ай бұрын
It's simple physics. Is the ratchet straps are rated for a certain amount of tensile strength then what's the compression rating on the spring and if you go 2 to 3 times over the compression rating. And it's locked in there's no more risk than using those spring compressors that could slide outside ways and shootout at someone
@wyattandwill1211 ай бұрын
Great idea. I have straps I purchased for lining up my control arms but I didn’t think to use them for the spring. Driver’s side went on with a pry bar but passenger’s side was more practical to go with this method. Thanks again 😁
@BellyUpFish
11 ай бұрын
Don’t die!
@wyattandwill12
11 ай бұрын
@@BellyUpFish My biggest concern would be something happening while the vehicle’s driving since I did the whole rebuild, I may pay the place I get my alignment done at to double check my work 👍🏻 (even while it’s as simple as torquing everything down)
@RollingLogs21 Жыл бұрын
Great video, and great hair! 👍😁 Did you know you can loosen a ratchet strap under tension one click at a time like a come-along? Set the ratcheting handle halfway between fully open and fully closed, and put some tension on it like you are going to tighten it further, but do not go far enough that it clicks. Then reach inside with your finger and pull back on the plate that engages the ratcheting pawls to disengage it from the pawls, and slowly let the ratchet handle move back toward the closed position (the tension load will pull it back). Once the ratcheting pawls clear the plate that you are holding back with your finger, release the plate so it engages the pawls at the next looser notch. Continue to do this one click at a time until all the tension is released. It takes longer, but it's a lot more controlled and less scary then just knocking 'em loose. That might be the "Safest, LESS dangerous way", ha ha!
@Derek_Garnham20 күн бұрын
my friends car came back from having a new spring fitted, it didn't drive right, when he looked there were still a few heavy duty zip ties compressing some of the coil. Maybe useful as secondary protection once the straps are tight.
@11green11 Жыл бұрын
great vid, been using this method since forever 🙏 car springs can mostly be done by leaning on them or zip off the bolt while it's laying on the side. It's the truck springs that are stout and pose a danger and a major PIA. 😬
@sailmirage
7 ай бұрын
Yes I agree. My springs don't look like his.
@willjones5816 Жыл бұрын
I did something very similar ~15 years ago with a dodge ram. If I can’t remember if it had the shock mount through the spring or if it was a coil over. Probably a coil over since I somewhat remember it being off the vehicle when I did it. I didn’t have a coil spring compressor and it was after hours on a weekend. I think I used four 1” ratchets working around one click at a time. The same for releasing the pressure. I still don’t understand why full-size trucks don’t have a removable shock. There’s room to mount it.
@prezo1975 Жыл бұрын
'The safest most dangerous way'🤣🤣 About to give this a go.. the helmets not a bad idea ! Thanks
@BellyUpFish
Жыл бұрын
Don’t die!
@wolmntn4 ай бұрын
When I was young and stupid I used hose clamps to hold the spring compressed when I took it off. I threw it and it went 50 ft into the sir. Needless to say I got the right spring compressor next time.
@caucasianafrican143511 ай бұрын
It's easiest if you wrap the strap around each level of the spring, laddering up.
@Xbox4life909 ай бұрын
U can use the weight of the car or truck . Just compress the spring with a jack under control arm, then loosen the middle top nut first.
@recall2880
2 ай бұрын
Then how do you the get the spring back on after?
@Franco-gn2rn9 ай бұрын
Great idea but I suggest you do that while on the car so you can use the weight and if some snaps it would just bounce inside the wheel area and not directly to yourself
@Bluelineclapper312 Жыл бұрын
Use thicker heavy duty straps rated for higher tension and you'll be fine.
@krisg8229 ай бұрын
....lift the car or teh side you want to work on, put the straps on the spring without removing the wheel if you can, lower the car, now pull on those levers untill the straps are somewhat tight. Lift the car :) now the spring remains compressed. That is how you do it, there will be some cars where there is not enough space to do that, but this method will work for many cars. You don't have to worry that the straps will tear apart due to friction, since you don't pull on the lever to compress the spring - instead the weight of the car does the job. 😏
@scotianbank8 ай бұрын
Would you say that this wouldn't be such a bad idea if I just needed to compress a spring on the front shocks on a 2019 Jeep Grand Cherokee in order to fit the shocks back into the car after adding a top-hat spacer for a 2.5" lift kit? So I wouldn't even need to remove the spring itself, since this kit doesn't come with a pre-load spacer, only the top-hat spacer. Not exactly sure how much I need to compress the spring, but it definitely is not the whole way, maybe 1/3 compression, 1/2 at most? Thanks!
@BellyUpFish
8 ай бұрын
Personally, I’d do it on my car, and while it would work, you should under no circumstances do this. ;) Disclaimer, disclaimer, disclaimer. 😆
@TG-om1ue2 жыл бұрын
if all three began to fail i wonder how long you would have to run away from the grenade
@BellyUpFish
2 жыл бұрын
Probably not as much time as it would take to get out of the blast zone.
@TG-om1ue
2 жыл бұрын
@@BellyUpFish Well, if someone doesnt come back from the future to tell you not to do something it cant be the worst idea xD
@BellyUpFish
2 жыл бұрын
@@TG-om1ue We can’t live forever! ;)
@Africanmechanics9 ай бұрын
LET ME TRY THE SAME ON MY CHANNEL
@daveo98449 ай бұрын
Safer than using poor fitting clamps 👍🏼
@BellyUpFish
9 ай бұрын
Those clamps are awful.
@KNIGHTJUMPS Жыл бұрын
So Elvis isn't dead. Cool.
@abandonbelief Жыл бұрын
StandingTree did not say thank you
@BellyUpFish
Жыл бұрын
I’ll have a talk with them.
@jimcatanzaro78082 жыл бұрын
If it works is it stupid
@BellyUpFish
2 жыл бұрын
Not if we don’t die! 😆
@jimcatanzaro7808
2 жыл бұрын
@@BellyUpFish springs are easy I usually drop the lower ball joints so no need to compress them
@tuggaworsley42819 ай бұрын
You replaced absolutely nothing - why did you embark on a biased exercise ???? (Why did l tune in & stay the distance???)
@BellyUpFish
9 ай бұрын
If you don’t understand what was demonstrated in the video - please - for your own safety, do not perform what you saw in the video. That said, thanks for watching. 😆
Пікірлер: 39
Safer than the clamps I've seen people using, I've watched alot of these jump out of cages but never had an issue with strapping them.
@BellyUpFish
Жыл бұрын
Seems like it’s definitely safer than the standard Autozone grade spring compressor.
@TechTimeElectronics
5 ай бұрын
It's simple physics. Is the ratchet straps are rated for a certain amount of tensile strength then what's the compression rating on the spring and if you go 2 to 3 times over the compression rating. And it's locked in there's no more risk than using those spring compressors that could slide outside ways and shootout at someone
Great idea. I have straps I purchased for lining up my control arms but I didn’t think to use them for the spring. Driver’s side went on with a pry bar but passenger’s side was more practical to go with this method. Thanks again 😁
@BellyUpFish
11 ай бұрын
Don’t die!
@wyattandwill12
11 ай бұрын
@@BellyUpFish My biggest concern would be something happening while the vehicle’s driving since I did the whole rebuild, I may pay the place I get my alignment done at to double check my work 👍🏻 (even while it’s as simple as torquing everything down)
Great video, and great hair! 👍😁 Did you know you can loosen a ratchet strap under tension one click at a time like a come-along? Set the ratcheting handle halfway between fully open and fully closed, and put some tension on it like you are going to tighten it further, but do not go far enough that it clicks. Then reach inside with your finger and pull back on the plate that engages the ratcheting pawls to disengage it from the pawls, and slowly let the ratchet handle move back toward the closed position (the tension load will pull it back). Once the ratcheting pawls clear the plate that you are holding back with your finger, release the plate so it engages the pawls at the next looser notch. Continue to do this one click at a time until all the tension is released. It takes longer, but it's a lot more controlled and less scary then just knocking 'em loose. That might be the "Safest, LESS dangerous way", ha ha!
my friends car came back from having a new spring fitted, it didn't drive right, when he looked there were still a few heavy duty zip ties compressing some of the coil. Maybe useful as secondary protection once the straps are tight.
great vid, been using this method since forever 🙏 car springs can mostly be done by leaning on them or zip off the bolt while it's laying on the side. It's the truck springs that are stout and pose a danger and a major PIA. 😬
@sailmirage
7 ай бұрын
Yes I agree. My springs don't look like his.
I did something very similar ~15 years ago with a dodge ram. If I can’t remember if it had the shock mount through the spring or if it was a coil over. Probably a coil over since I somewhat remember it being off the vehicle when I did it. I didn’t have a coil spring compressor and it was after hours on a weekend. I think I used four 1” ratchets working around one click at a time. The same for releasing the pressure. I still don’t understand why full-size trucks don’t have a removable shock. There’s room to mount it.
'The safest most dangerous way'🤣🤣 About to give this a go.. the helmets not a bad idea ! Thanks
@BellyUpFish
Жыл бұрын
Don’t die!
When I was young and stupid I used hose clamps to hold the spring compressed when I took it off. I threw it and it went 50 ft into the sir. Needless to say I got the right spring compressor next time.
It's easiest if you wrap the strap around each level of the spring, laddering up.
U can use the weight of the car or truck . Just compress the spring with a jack under control arm, then loosen the middle top nut first.
@recall2880
2 ай бұрын
Then how do you the get the spring back on after?
Great idea but I suggest you do that while on the car so you can use the weight and if some snaps it would just bounce inside the wheel area and not directly to yourself
Use thicker heavy duty straps rated for higher tension and you'll be fine.
....lift the car or teh side you want to work on, put the straps on the spring without removing the wheel if you can, lower the car, now pull on those levers untill the straps are somewhat tight. Lift the car :) now the spring remains compressed. That is how you do it, there will be some cars where there is not enough space to do that, but this method will work for many cars. You don't have to worry that the straps will tear apart due to friction, since you don't pull on the lever to compress the spring - instead the weight of the car does the job. 😏
Would you say that this wouldn't be such a bad idea if I just needed to compress a spring on the front shocks on a 2019 Jeep Grand Cherokee in order to fit the shocks back into the car after adding a top-hat spacer for a 2.5" lift kit? So I wouldn't even need to remove the spring itself, since this kit doesn't come with a pre-load spacer, only the top-hat spacer. Not exactly sure how much I need to compress the spring, but it definitely is not the whole way, maybe 1/3 compression, 1/2 at most? Thanks!
@BellyUpFish
8 ай бұрын
Personally, I’d do it on my car, and while it would work, you should under no circumstances do this. ;) Disclaimer, disclaimer, disclaimer. 😆
if all three began to fail i wonder how long you would have to run away from the grenade
@BellyUpFish
2 жыл бұрын
Probably not as much time as it would take to get out of the blast zone.
@TG-om1ue
2 жыл бұрын
@@BellyUpFish Well, if someone doesnt come back from the future to tell you not to do something it cant be the worst idea xD
@BellyUpFish
2 жыл бұрын
@@TG-om1ue We can’t live forever! ;)
LET ME TRY THE SAME ON MY CHANNEL
Safer than using poor fitting clamps 👍🏼
@BellyUpFish
9 ай бұрын
Those clamps are awful.
So Elvis isn't dead. Cool.
StandingTree did not say thank you
@BellyUpFish
Жыл бұрын
I’ll have a talk with them.
If it works is it stupid
@BellyUpFish
2 жыл бұрын
Not if we don’t die! 😆
@jimcatanzaro7808
2 жыл бұрын
@@BellyUpFish springs are easy I usually drop the lower ball joints so no need to compress them
You replaced absolutely nothing - why did you embark on a biased exercise ???? (Why did l tune in & stay the distance???)
@BellyUpFish
9 ай бұрын
If you don’t understand what was demonstrated in the video - please - for your own safety, do not perform what you saw in the video. That said, thanks for watching. 😆
😳😳😱😱🙄🙄🙄