DIY Making a set of Trap Spring Setters
www.selfrelianceoutfitters.com
astore.amazon.com/davecante-20
Dave Canterbury, David Canterbury, The Pathfinder School,Bush Craft ,Survival skills, Historical Lore, Primitive Skills, Archery, Hunting, Trapping, Fishing, Navigation, Knives, Axes, Fire, Water, Shelter, Search and Rescue
Пікірлер: 28
Another great video Dave... knew it wouldn't take a rocket scientist to make them but this just shows the simplicity & how quickly someone like myself can do it. Thanks again & keep these coming!
I have been waiting for this video ever since i knew what trapping was, so thank you
Dave to make it easier you can clamp both pieces together and grind both spring notches at the same time.
why work hard when you can work smart. trap setters are always in my pack. might not use them but atleast i have them. always great videos Dave
thanks for the video Dave you just saved me $25 plus.thanks again
Me and my father last year set a 220 conibear to catch an otter, it was 10 degrees out and it was near impossible to set it. Wish we had some trap setters that year
thanks for the video Dave great info.
Mr. Canterbury, I enjoy your page a lot and watch many of your videos between classes and studies at my college. I am a Natural Resource major. I have been in a wheelchair for 25 years (my whole life) and also have a muscle disease. I do not have the strength to compress the springs on even the small foot hold traps. Does a pair of trap setters give you enough leverage to make it easier to compress the springs? The 21st Century Longhunter is my favorite series. Thank you, Jackie Newman
man I love your toolshed!
When you cut flat bar in a chop saw turn it on its edge it cuts much easier. Great video. Thanks for all the info
@DavidCanterbury
7 жыл бұрын
That makes sense
Hey Dave, I have enjoyed your run on Dual Survival, KZread and Dirty Rotten Survival. Thanks for all that you do. I made a set of these last year. I got the steel from Tractor Supply as well. I didnt cut them down to 18" though and they bent on me the first time i tried them. I know you do blacksmith work so I have a question for you. I have since straightened the steel back out. If I heat the steel up to red hot will it harden the metal so it doesnt bend with me? Thanks
@brendanlyster195
7 жыл бұрын
From my experience i would say you need to cool it rapidly(like putting it in water or oil) once you heat it up. If you let it air dry it will become softer. Also from Georgia.Try his blacksmithing videos he has them on a playlist.
cool project
hey Dave could you put a pair of wire cutters down close to the Bolt would make a nice backup
What size drill bit did you use? Did you say the hole was drilled 8 inches from the notch end? Thanks
I recently bought a couple of Duke 110s and thought man why can't I set these it's been 40 years or more since I've trapped people say your getting old and weak but I had Victor 110s before and set them when I was 12 years old and can still set them I'm making a pair of setters it will just make things alot easier and faster
I was thinking maybe just one washer in between the arms on the center bolt/pin and that would provide less friction. Don't know, just my observation. Great video Dave! Later...
@DavidCanterbury
7 жыл бұрын
That is good food for thought no doubt
Chuck Norris called Dave a sissy once, just once! Great video Dave I love DIY videos.
@hugofilipeantunes
7 жыл бұрын
Bill Fisher if Chuck called Dave a sissy only once, thats a great sign.. Hehehehe
Trap spring... spring trap... SPRINGTRAP!
if the pivt point gets lower you get more leverige les power needes
Why drill the hole slightly off center?
@DavidCanterbury
7 жыл бұрын
Mechanical Advantage
Hat up. You have tools.
support!
Dear .. Do Video, you can translate into Arabic? Because you have followers Arabs So I hope attention so ... Thank you and greetings Alaptoviq