DIY Knight Rider Scanner LED Light System With Just 3 Wires | Arduino | WS2812B | Design 1
Ғылым және технология
#LEDChaser #KnightRider #Arduino
This is one of the most realistic Knight Rider (WS2812B LED Strip) light systems with tail fading effect. This is very easy to build with just 3 wire connections to Arduino Nano. Free Arduino code is given below. If you want to change the number of LEDs and Color of the design, check this video - • How To Make a Multi Co...
Connect with me on Facebook - / hazi.tech
Follow me on Instagram - / hazi_tech
Reach out to us at info.hazitech@gmail.com or via WhatsApp at +94779299171 for any personalised services or custom job requests.
We specialize in creating customized lighting solutions tailored to your vehicle's unique style and preferences. Whether you're looking for a specific size or design, we've got you covered. Our team can provide you with a personalized code for your custom lights or even ship complete controllers pre-programmed with the code of your choice. With over 100 successfully completed projects worldwide and more in progress, you can trust us to deliver exceptional results.
If you find this video enjoyable, I kindly encourage you to express your support by liking and subscribing. Your engagement not only fuels the growth of the channel but also serves as a tremendous motivation for me to create more captivating content. Thank you sincerely for your invaluable support!
kzread.info?sub...
How To Make New Knight Rider Ford Mustang Scanner Light System - • How To Make New Knight...
Police/VIP/Knight Rider LED Light System With Push Button Control - • How To Add a Push Butt...
Arduino Knight Rider Mustang LED Scanner | Any Colour, Pattern and Size - • Arduino Knight Rider M...
“Knight_Rider_Design01” Arduino code
Free content no longer available. For code purchase with upgraded controller, contact us at info.hazitech@gmail.com
Arduino Software 1.8.12 and “FAST LED” Arduino library (FastLED-3.3.3)
• How To Install Arduino...
Parts List
ATmega328P Nano V3 Controller Board (Arduino Nano)
www.banggood.com/Geekcreit-AT...
WS2812B RGB LED Strip Light 144LED pixels/leds/m IP65
www.ebay.com/itm/WS2812B-Stri...
DC-DC 7-28V to 5V 3A Step Down Power Supply Module
www.banggood.com/DC-DC-7-28V-...
330 ohm Resistor
www.banggood.com/20pcs-2W-Met...
Optional Parts
Mini Solder-less Prototype Breadboard
www.banggood.com/Mini-Solderl...
Male To Male Jumper Cable
www.banggood.com/40pcs-10cm-M...
How To Make a Knight Rider (KITT) Scanner LED Light System With Just 3 Wires | Arduino | Design 1,Pixel LED knight rider, WS2812B knight rider, knight rider led strip, knight rider light bar, knight rider led light bar, knight rider circuit arduino, knight rider project ,knight rider led scanner, knight rider circuit, knight rider light bar installation, Arduino Knight Rider Example with Code, knight rider,arduino flash lights, karr knight rider, led chaser, night rider ,knight rider circuit using 555 timer, larson scanner kit, larson scanner circuit, larson scanner arduino code, larsen led, Larsen led lights
Пікірлер: 178
For more designs, check out this video series on Easy To Build LED Light Systems kzread.info/head/PL4dsTE_604gvwvnnnKTFg-bDIQMbbrZLh
Sorry I'm completely new to Arduino. Can the breadboard be used as the final product for the control? Or do you have a video on how to make a nicer looking finished control? Thanks!
Nice video. It's always a pleasure to watch Your videos. Keep up the good work.
@HAZITECH
2 жыл бұрын
Thank you so much for your kind words.
Yes ! Great video
@HAZITECH
4 жыл бұрын
Thanks!
Thank you so much !!
@HAZITECH
4 жыл бұрын
You are welcome
Great project.
@HAZITECH
3 жыл бұрын
Thanks a lot
seus trabalhos são top, parabéns!
@HAZITECH
3 жыл бұрын
Muito obrigado. Espero que você continue assistindo meus vídeos. Por favor, compartilhe meus vídeos como um suporte. Boa sorte.
Well done bro. Nice work
@HAZITECH
4 жыл бұрын
Thank you so much 😀
Checked your channel. Very good content machan... All the best
@HAZITECH
3 жыл бұрын
Thanks a lot brother 🙏🏻
Good work👍
@HAZITECH
4 жыл бұрын
Thanks a lot
great project is exactly what I was looking for keep it up :-)
@HAZITECH
4 жыл бұрын
Thanks a lot
@Theshadowcar
2 жыл бұрын
@@HAZITECH I hope you write us the pieces we need to make.
@HAZITECH
2 жыл бұрын
Parts list is linked in the video description as usual. Please take a look.
@Theshadowcar
2 жыл бұрын
@@HAZITECH thanxs man
@HAZITECH
2 жыл бұрын
You are welcome
Nice work
@HAZITECH
4 жыл бұрын
Thank you very much!
Would you make something like this exactly but be able to add in leds for brake light? Like every other led that would be used for brake lights.
@HAZITECH
Жыл бұрын
Hmm that is something I need to test.
nice work.....
@HAZITECH
3 жыл бұрын
Thanks a lot
Hazi can I use a 12v to 5v 12 watt power step down in this set up? I need to run the nano plus another power source for brake lights. Could I install step down on power line of leds would it effect the 330 ohm resistor?
@HAZITECH
Жыл бұрын
You can use a 12v to 5v step down. That’s what I did too. 330 ohm resistor does not affect by it.
Super Stuff Hasitha..........
@HAZITECH
3 жыл бұрын
Thanks a lot
If you could update the software or send me one for 3 wire leds
I have a very unique looking ebike. Would the coded need to be altered if I cut excess lights out? I just want it for the back of the seat.
@HAZITECH
2 жыл бұрын
Yes. But there are many options you can choose from the below linked videos with the ability of simple led quantity change. Check it out. kzread.info/head/PL4dsTE_604gvwvnnnKTFg-bDIQMbbrZLh
Genius
@HAZITECH
2 жыл бұрын
Thank you so much 😊
niyamai machan
@HAZITECH
4 жыл бұрын
Thanks a lot brother
Great Project! What if I only have a 24 LED strip, how do I modify the coding? With 80LED strip setting it only flows in one direction, even with speed at 5.
@HAZITECH
3 жыл бұрын
Simply changing the number of LEDs won’t work without a major code change. If you can send me your email address I can send you the modified code for 24 LEDs. My email address is hazi.rc.tech@gmail.com
@HAZITECH
3 жыл бұрын
Code was emailed. Check it and let me know. If you want to help me out and grow this community, please share my videos. Thanks!.
@HAZITECH
3 жыл бұрын
Check this out. You will love it. kzread.info/dash/bejne/ZGGtt8Nmf5DbZ5s.html
Hi Great Job !!! I have a question because im "noob " in arduino ... I add skrtch with daylight etc its working but i wanna add a knightrider mode can you tell me how to do it ?? Thanks and Best Regards ;-)
@HAZITECH
2 жыл бұрын
Hey, I’m planning to add it to my next version which will be released next week. Stay tuned.
Are leds wired together for ground and power or do they need to be separated
@HAZITECH
2 жыл бұрын
These are addressable LEDs comes in a strip.
Hazi I need help. I'm using arduino due. How would I hook up 330ohm resistor? I don't have bread board
@HAZITECH
Жыл бұрын
Use the exact same pin number
Asombroso! Cuantos leds por metro recomiendas 60, 74, 96 o 144 o no importa? Awesome! How many leds per meter do you recommend? 60, 74, 96, 144 or it doesn't matter?
@HAZITECH
Жыл бұрын
I use 144LED/m. That is the best.
Thanks 🌷🌷🌷🌷🌷🌷🌷🌷🌷
@HAZITECH
4 жыл бұрын
Thanks 🙏
Is it possible that, we can run white light like snake means from start to end its getting on one by one n at the end its completely on then i want to flicker 2 times
@HAZITECH
Жыл бұрын
Yeah it can be done. But a fully different coding should be done.
@danishhaseen
Жыл бұрын
@@HAZITECH can you share if possible?
Patta.. eka
@HAZITECH
4 жыл бұрын
Thanks a lot bro.
Can the jumper wires be soldered to the arduino nano or due for permanent use?
@HAZITECH
Жыл бұрын
Yes you can permanently solder those.
Can the controller work per LED? or is its best resolution 8*10LED zones?
@HAZITECH
7 ай бұрын
The latest versions can work per LED. Reach out to us at info.hazitech@gmail.com or via WhatsApp at +94779299171 for latest code or controller purchases.
Is it possible to have this work with 55W halogen bulbs using relays? I'd like to see about making an ardiono control module, but with real lights.
@HAZITECH
4 жыл бұрын
Actually it can be done with an array of transistors. Basically exact copy of what KITT has. I did it some time back. If there is enough demand, I'll make a full video guide.
@gustavodelamora3676
4 жыл бұрын
@@HAZITECH WEll I know in the real show they used relays and 55W halogen bulbs. However it would be neat to have a small control module like an arduino where you can adjust speed and have other scan modes .Maybe even add the sounds module.
@HAZITECH
4 жыл бұрын
Yes indeed. Good though of adding a sound module 👍🏻. Using transistors is ideal for durability and smooth fade effects. I’ll try to make a sample video on that. Thank you very much for your input. That motivates to do more stuff. Please feel free to subscribe and share the video as a support. More design videos are coming within 1-2 days. Stay tuned 👍🏻
Ideally I would love to use this chasing light same as Kitt did, but in Canada red light is not allowed on the front of the cars (only reserved for police). If I change the color or move it to the back of the car... well... it won't be a kitt anymore :) So I decided to go with red on the front but to only have it triggered by the car un/lock, for a brief 30 seconds. I have no clue about coding but I was wondering how to change the program to start on a short 12V positive pulse (door actuator) and to stop after 30 sec or say 10 running cycles
@HAZITECH
Жыл бұрын
Reach out to us for any personalized services or custom job requests - 📧 info.hazitech@gmail.com
@WolfODonne11
Жыл бұрын
Same for me, but im just going to make a yellow one like KARR had
@HAZITECH
Жыл бұрын
Great. Let mw know if you need any hardware. info.hazitech@gmail.com
Can this be made in a smaller 5" version?
@HAZITECH
2 жыл бұрын
Yes. There are videos in the playlists where you can change the number of LEDs pls check.
Supiri
@HAZITECH
3 жыл бұрын
Thanks a lot
Hello, do you make custom orders, ie...ready made? if so how do i contact you. Regards
@HAZITECH
3 жыл бұрын
Hello, I can do custom designs based on your requirement and send you the code. Then you have to upload the code and assemble the unit. Sorry I cannot ship full units. You can contact me via HAZI TECH FB page or drop an email to hazi.rc.tech@gmail.com. Thanks
Thank you for this project... i really appreciate it! if you don't mind, can you add police function on this project?
@HAZITECH
2 жыл бұрын
Thanks. I already did it. Please see my video Playlists.
@MharGarcia
2 жыл бұрын
@@HAZITECH can you give me the link please? i want to do in my car. Knight Rider with Police after i press push button
@HAZITECH
2 жыл бұрын
Here you go Easy To Build LED Light Systems kzread.info/head/PL4dsTE_604gvwvnnnKTFg-bDIQMbbrZLh
What led strip are you using? Ws2812?
@HAZITECH
Жыл бұрын
Yes WS2812B
The 330 ohm resistor is it .5 watts ?
@HAZITECH
Жыл бұрын
1/4 watt is enough
What if I want this but with the light being white?
@HAZITECH
3 жыл бұрын
Hi, for an example, in the code "CH1(LED_POWER_7, 0, 0)" corresponds to CH1(Red,Green,Blue) values. So if you want to have white instead of Red, you can copy and paste the Red value to Green and Blue. Eg1. CH1(LED_POWER_7, LED_POWER_7, LED_POWER_7), Eg2.CH2(LED_POWER_6, LED_POWER_6, LED_POWER_6). Since white is consuming more power, make sure to power the LED strip from both ends.
Niyamai
@HAZITECH
4 жыл бұрын
Thanks a lot
The real night rider illumination with a trail. How much for the led reel?
@HAZITECH
4 жыл бұрын
Hi, Waterproof strip is around Rs.3000 per 1m. Non-waterproof option is around Rs.2000 per 1m. I'll put links in the description.
In my arduino cant upload/ error, the description sketch is too big bro, how to handle it?
@HAZITECH
3 жыл бұрын
Have you tried updating your Arduino IDE and adding the latest FastLED library?.
does it matter, whether the 330ohm resistor is 2w or 1w?
@HAZITECH
3 жыл бұрын
Not at all. You can use either. Even without the resistor this works. It is for extra protection.
@kristjanp.6613
3 жыл бұрын
@@HAZITECH Alright, thanks for the fast reply, just earned yourself a new sub!
@HAZITECH
3 жыл бұрын
Thanks a lot 👍🏻
I am trying to download the program to my Arduino Uno and and it keeps telling me that the 'leds' was not declared in the scope.
@HAZITECH
3 жыл бұрын
Have you added the FastLED library
@HAZITECH
3 жыл бұрын
Try this first kzread.info/dash/bejne/X6OEpdJ_YbjUm5c.html
Randam colour pallet wage ewa dan widhiya poddak kiyala denwadha
@HAZITECH
3 жыл бұрын
Brothet Arduino IDE eke examples walata FastLED kiyana ekata yanna. Eeke colour pallet wage thawa godak examples thiyanawa. Eee oona ekak open karala code eka upload karala balanna. Mathaka ethiwa code eke mula number of LEDs walata oyage LED gaana danna.
Meke run wena light set eka kota karanne kohomada.led 23k thiyana strip ekakata yalu.
@HAZITECH
3 жыл бұрын
Meka balanna bro. Meke wage LED 24 hadanna puluwan. kzread.info/dash/bejne/ZGGtt8Nmf5DbZ5s.html
@actioncut9888
3 жыл бұрын
HAZI TECH meke dn light eliya godak digata thiyanawane.meka tikak kota karanna berida.
@HAZITECH
3 жыл бұрын
Me video eke anthima pattern eka balanna kzread.info/dash/bejne/p6atwcmPhdCbZpc.html
Hazi when uploading to my nano it attempts 8 to 10 times then I get avrdude error can you help? I was able to get one nano to work but on my 3rd now
@HAZITECH
Жыл бұрын
Hey, in Arduino IDE, go to Tools - Processor and then select ATmega328P (Old Boot loader) if you are current at ATmega328P. Or other way around. Then upload the code. This should work fine.
@samuelfrodge4988
Жыл бұрын
@HAZI TECH thank you this did work
@HAZITECH
Жыл бұрын
Awesome 👌🏻
@HAZITECH
Жыл бұрын
If you don’t mind, spread my channel by sharing my videos. That do help me a lot. Thanks!.
plz the code source for arduno
@HAZITECH
3 жыл бұрын
In my all videos the code is linked in the video description. Please take a look
Colors wenas karanne kohomada please
@HAZITECH
2 жыл бұрын
Brother mage e gena video ekak thiyanawa. Poddak balanna playlist eke.
Hi, can you make the code for this project available?
@HAZITECH
5 ай бұрын
For code purchase, contact us at info.hazitech@gmail.com or WhatsApp at +94779299171
Me strip ek kohenda gaththe
@HAZITECH
3 жыл бұрын
eBay mama link dala thiyanawa video description eke.
great work,mata arduino cord eka denna puluwanda
@HAZITECH
3 жыл бұрын
Thanks. Hemadama, hema video ekakama mama code eka description eke link karala thiyanawa. Balanna.
Software link in your description doesn't work.
@HAZITECH
Жыл бұрын
It works. I have just tested. Use your PC to open the link.
Only have 60 led strip how do modify the coding
@HAZITECH
2 жыл бұрын
Please go to my playlists. There you will find a video which can change the number of LEDs. It’s called “Knight rider multi LED”
@HAZITECH
2 жыл бұрын
Here is the link kzread.info/dash/bejne/ZGGtt8Nmf5DbZ5s.html
@jayanthannithushan6906
2 жыл бұрын
@@HAZITECH ok thank you
donde consigo el codigo arduino
@HAZITECH
Ай бұрын
For code purchase, contact us at info.hazitech@gmail.com or WhatsApp at +94779299171
Looked at your videos. None show how to wore the power supply module
@HAZITECH
Жыл бұрын
Every video wiring diagram shows that. Please take a look. You can supply 12V from anywhere (accessory power, park light, etc.)
@samuelfrodge4988
Жыл бұрын
Can the arduino duo be used instead of this one?
@HAZITECH
Жыл бұрын
Yes you can
Hi Hazi, I have 60 led lights, is it possible for you to send me code for 60?
@HAZITECH
2 жыл бұрын
I have made a custom code where you can change the number of LEDs. Just search “HAZI TECH Knight Rider” in KZread.
i cant download the code.This is the only one that looks good on the entire internet too!
@HAZITECH
Жыл бұрын
Wow thanks a lot. Try your PC to download the code. And there are many more improved versions in my playlists. Take a look.
I keep trying to Upload it but the program tells me that an error occured Pleased Help!!
@HAZITECH
3 жыл бұрын
Hi, what is the error that you are getting?
@craigcraigerson6075
3 жыл бұрын
@@HAZITECH I dont exactly know, it just tells me that an error occured, the text underneath the error message just tells me that something didnt sync right
@HAZITECH
3 жыл бұрын
Hmm, send me a screenshot of the full error to HAZI TECH FB page
@craigcraigerson6075
3 жыл бұрын
@@HAZITECH Is it possible to send it via E-Mail ? I dont have Facebook
@HAZITECH
3 жыл бұрын
Yes sure. Send an email to info.hazitech@gmail.com
Me ic aka progrem karanne kohmda
@HAZITECH
2 жыл бұрын
Arduino Nano board ekak program karanne. Godak lesi. KZread eke poddak search karanna.
@krishanmadushanka4950
2 жыл бұрын
@@HAZITECH tnx aiye
Are u selling these?
@HAZITECH
Жыл бұрын
Sorry no
Bro Code eka compile error venawa.
@HAZITECH
3 жыл бұрын
Mokakda ena error eka?
Search a Great video
@HAZITECH
4 жыл бұрын
Thanks 😊
AliExpress power module eka 2USD wenne same module
@HAZITECH
3 жыл бұрын
Mama gaththe eBay. Den prices wenas wela ethi brother.
@manjulabw
3 жыл бұрын
@@HAZITECH rgb strips walin budhurasmala ekak hadna video ekak danna puluwanda
@HAZITECH
3 жыл бұрын
Mama hadapu Budurasmala okkoma strips walin hadanna puluwan kisima wenasak na.
@manjulabw
3 жыл бұрын
@@HAZITECH strips Walin lesi neda meta wada? strips wena wenama kapala neda alawanna ona
@HAZITECH
3 жыл бұрын
Strips wena wenama solder karanna oona. Bulb holes widinna oona. Oyage kemeththa thama.
Light patiya podi akak ganna berida yalu
@HAZITECH
4 жыл бұрын
E kiwe diga adu patiyakin hadanna puluwanda kiyana ekada bro?. Puluwan oona digakata hadanna puluwan. Code eka update karanna oone.
@sandeeprox6053
4 жыл бұрын
Cohomada ubdet karanne
@HAZITECH
4 жыл бұрын
Bulb keeyak wage set wennada?. Diga?.
@sandeeprox6053
4 жыл бұрын
Mata oyage nombare awannako imo ake
@sandeeprox6053
4 жыл бұрын
L. E. D 45 thiyenawa Bro
it's a pity that all the codes on your channel are paid (((
@HAZITECH
Ай бұрын
I gave all the codes for free for 3 years. But nobody values what is given for free. So here we are.
Turn off the music and TALK (if you are able to)
@HAZITECH
Жыл бұрын
I’ll try 👍🏻