I normally never comment on YT videos but this video was well thought out and well paced. Nice job

@TheMissingBolt

2 жыл бұрын

Thank you very much! 🙂

I have 14 years this car and I didn't knew this hidden menu tnx friend

@TheMissingBolt

Жыл бұрын

You’re very welcome! 😊

great instruction in a good tempo and clear message - thank you

checking the coolant temp -- learned something new.. thanks!

@TheMissingBolt

3 жыл бұрын

You're welcome!

Foarte bună prezentarea, ai explicat în detaliu procesul, baftă incontinuare 😉

@TheMissingBolt

6 ай бұрын

Multumesc mult!😀

Vauxhall Corsa 1.4 E model 2016 plate followed your instructions but I have not worked on this particular model of Vauxhall before have had Vauxhalls different procedure after following your video to the letter antifreeze changed was successful well done brilliant video and also guys make sure you check under the wiper tray motor assembly four leaves and muck if you do not keep it clean water will start coming into the front foot Wells once again thank you

Thanks for your vídeo! I’m gonna try it out tomorrow !

Great presentation skills and useful content. Keep it up!

@TheMissingBolt

10 ай бұрын

Thank you! Much appreciated!

Excellent video,very clear and well presented.

@TheMissingBolt

4 ай бұрын

Many thanks!

Thank you, found this very useful 👍 😀

@TheMissingBolt

2 жыл бұрын

Happy to help :)

Brilliant vid, subscribed!

@TheMissingBolt

Жыл бұрын

Thanks a lot!

Brilliant vid mate best ive seen! thanks 👍👍👍👍👍👍

@TheMissingBolt

8 ай бұрын

Thank you very much! Glad you enjoyed it!

Great help! I’m going to try this asap, beats paying £70 when I can do it myself lol

@TheMissingBolt

2 жыл бұрын

Your car and your wallet will thank you for it! 😀

@MarlySmith

2 жыл бұрын

If it already had a bit of water in do I still need to drain before putting in the ready mixed antifreeze I’ve already bought?

@TheMissingBolt

2 жыл бұрын

@@MarlySmith You need to check your antifreeze concentration in the system before deciding. If your ready-mixed antifreeze is 50% - 50%, you can skip the draining of whatever is in the system only if (1) it's not old and dirty and (2) if the existing concentration in the system is also 50 % - 50 %. If the coolant is old and / or dirty you should drain it out of principle. Otherwise, you first need to get whatever is in the system to a 50 % - 50 % mix first, by adding either distilled water or concentrated antifreeze progressively.

Good job bro 👍 thanks.

@TheMissingBolt

3 жыл бұрын

You're welcome :)

Wow, thank you for info about hidden menu, greetings from Poland bro.

@TheMissingBolt

3 жыл бұрын

You're welcome! Happy to help :)

@huss9629

2 жыл бұрын

@@TheMissingBolt Hi I have been toping up my car with tap water every month instead of coolant for the last 3 years now whenever I top up the water it reduces very quickly does this mean it needs a coolant change the car is 10 years old with no service history the coolant may never have been changed

@TheMissingBolt

2 жыл бұрын

@@huss9629 From what you're describing it sounds to me like you have a leak in the cooling system. Coolant should require top-up only occasionally if everything is well. Do you see puddles of water underneath your car? Does your car appear to be constantly smoking at the back when you're driving?

@huss9629

2 жыл бұрын

@@TheMissingBolt No puddles or no smoke the car is 10 years old I dont think the coolant has ever been changed it has just been topped up with water I think the water just dissolves as water boils fast that's why we need to keep topping up with water what do you think?

@TheMissingBolt

2 жыл бұрын

@@huss9629 If there are no puddles and no smoke when driving, then most likely the water's evaporating due to heat. From what I've seen, coolant temperature on a Corsa D frequently goes over 100 degrees C. In this case yes, adding coolant should 100 % help, since the coolant not only lowers the freezing point, but also raises the boiling point of the mix. Also, coolant has additives for lubricating the water pump and preventing the rust that becomes inevitable if you use just plain water.

Excelent videos 👍👍

@TheMissingBolt

10 ай бұрын

Thank you very much!

Tip, To take air out, place the car after driving on the Road for a while , on a Hill first front up en let it run for Some minutes , then turn the car on the Hill front down , and let it run Again for Some minutes. The air wil disappear better.

@TheMissingBolt

Жыл бұрын

Ok, that's good to know. Personally I haven't tried this method, I found the standard method of letting the circuit self-bleed sufficient.

@Miladmirzaei25

2 ай бұрын

The work is done with the ventilation screw??!

Very good video, thanks! I watched it because I was looking for an information about the optimal level of cooling liquid. And foud very interesting information about hidden menu 😁 What other parameters does it show? Where can I find some more informations about it?

@TheMissingBolt

Жыл бұрын

I'm glad you liked the video. This post should give you more details on the hidden menu: mr-fix.info/opel-corsa-d-hidden-diagnostic-menu/

Thanks!!!!!!!!

Bravo. Teşekkürler

@TheMissingBolt

10 ай бұрын

Thank you very much!

EXCELLENT 💯👍

@TheMissingBolt

Жыл бұрын

Thanks! 👍

The red pointer on top of that guage is supposed to be upright to get a correct reading

@TheMissingBolt

2 жыл бұрын

True, but the pointer is supposed to have a small weight at the bottom, such that it is kept upright when enough coolant is inside. Mine didn't have that weight (it had detached from the pointer), which meant the pointer couldn't be kept vertical no matter what I did. So I just did my best to keep the entire tester as vertical as I could.

Hi, Video is good and well explained. What i would like to know, the plastic drain plug have you removed it fully. I found i had to do this. There was a small o ring on the plug and looked like an o ring was missing. So i fitted two back on. Did you notice this at any stage before.

@TheMissingBolt

2 жыл бұрын

Hello! I definitely didn't remove the plastic drain plug fully, because I didn't need to. It still has the original o-rings on it. And in the 9 months that have passed since I made the video, I haven't had any coolant leaks, so those o-rings are still doing their job properly.

The operating temperature of this engine is 103-110 degrees and the thermostat opening temperature is 103 degrees, and it opens smoothly, so you have to warm up the CT in the engine to 105-110 degrees approximately depending on the gearbox, bcz with the automatic one Aisin Warner AW6040LE we have 3 fan speeds which go off at 106 109 112 degrees accordingly and on all manual and MTA we have only 2, which are 109 and 112. All the best 🙂

@TheMissingBolt

8 ай бұрын

Indeed, I noticed the thermostat beginning to open at 103 using the OBD2 scanner. I thought it's a rather high value, but then again in most modern cars the cooling system runs at a higher temperature and pressure, in the name of greater "efficiency". Whenever I have to change the coolant, I always warm up the car by driving it for a while, a good 10 - 15 minutes after it reaches operating temperature; I never warm it up in-place as it takes too long and causes unnecessary additional engine wear. I've found that this interval is sufficient for the old and new coolants to mix up homogeneously.

@corsik737

8 ай бұрын

​@@TheMissingBolt ​ Regarding operating temperatures, yes it increases efficiency, and it's not some kind of new technology, just look at BMW engines. However these engines have a variety of versions. First of all, Corsa D has 4 1.4 engines: Z14XEP, A14XEL, A14XER and A14NEL. Now we are talking about your 1.4 on a Corsa D so it's gonna be A14XEL or A14XER (it's not possible to identify by this video). These engines have the folowing variants: with twinport and with EGR, without EGR and with twinport, with twinport and withouth EGR (which is most common from 2009 till 2012), without twinport and without EGR (which is the most common from 2012 till 2014) and also there are two types of thermostates which were installed in these engines: electric one (which you basicly have and the majority has, starts opening at 103 degrees at 0V) and the rare - bypass one which opens at 80 degrees at 12V. All of these variants have different ECU software. Now regarding warming up the engine. According to the Opel KTA maintenance document: "Allow engine to warm up at idling speed of up to 2500 rpm until first radiator fan setting switches on" . Basicly you don't have to stand on idle rpms as if you will stay the engine idling for a very long time, it will definitely cause damage due to low efficiency of the oil pump and insufficient lubrication. However, when you standing on 2500 rpm there is less load on the engine compared to 2500 rpm when you're driving and this is a big advantage and this is why it's written like that in manual. But there's also an advantage when you're driving, the engine will warm up a bit faster and one more advantage - under the load the more force will be exerted on the piston rings and pistons under engine load, meaning they will be less prone to skewness. However in the manual it is not written to go 2500 rpm immediately just aftern the engine start, and it's a kind of gap in the ,manual. What I would recommend. If the outside temperature is low, like 0 and etc, start up the engine and warm it up to ECT of 40-50 degrees at 1500 rpm and then rise to 2500 as at temperature of 42 the engine load is decreased enough but it also depends on your oil. Why 1500? If have a Tech2 or Op-COM (Vaux-COM), turn on the ignition and check desired idle value - it will be 1498, this is the algorythm of the ECU to rise rpm to 1498 just after each cold start and then slowly decrease it depending on the temperature. In two words, something like this :)

@TheMissingBolt

8 ай бұрын

@@corsik737 Ok, thanks a lot for your detailed explanations and advice! Our engine is an A14XER from 2014, for reference.

@corsik737

8 ай бұрын

@TheMissingBolt Yeah, A14XER was produced in a bigger quantity compared to A14XEL and I also thought that it's A14XER. The difference is just an ECU software so you can distinguish only by the engine marking label (it is located at a juction between the engine block and the gearbox) that is not visible on the video and most likely rusted, by VIN, by certificate of confirmity or other car's docs, by communicating with Corsa with an Op-COM or Tech2 and also by acceleration ⚡️

Hola buenos dias he estado mirando mi coche y no tiene valvula para purgar circuito del agua ...hay alguna otra forma de purgar el circuito?..gracias

@TheMissingBolt

5 ай бұрын

¡Hola! Si no tiene una válvula de purga, simplemente llene el refrigerante muy lentamente (para no agregar demasiado aire al sistema), luego conduzca el automóvil normalmente y verifique el nivel de refrigerante después de que el automóvil se haya enfriado. El nivel bajará a medida que se purga automáticamente, por lo que deberás recargarlo en consecuencia. Repita este paso tantas veces como sea necesario hasta que el nivel de refrigerante ya no baje.

Hey I have changed my coolant and I have noticed that the hoses have pressure in them when the car is hot. What does that indicate?

@TheMissingBolt

2 жыл бұрын

Hi! After the cooling system has been completely purged of air, all coolant hoses are full of liquid coolant, so it's normal for them to feel pressurized and harder to squeeze. Also, the entire system is supposed to be air-tight (if there are no leaks), in order to allow it to pressurize as the coolant temperature rises, so as to further increase the coolant's boiling point. So what you've noticed is just normal behavior.

Can you explain also what the other numbers and stuff are in the hidden menu thanks

@TheMissingBolt

2 ай бұрын

I found this forum post which provides the details: www.ukcorsa-d.com/threads/hidden-menu-info-all-in-one-place.34861/

hy, how did you put back the underneath metal body shield?

@TheMissingBolt

2 жыл бұрын

It's simple, the shield is held in place with 4 bolts, as you can see at 4:05 - 4:20. You have to slide it towards the back, over the existing rear bolts and then tighten all 4. The front bolts came with 2 special nuts as part of the shield's packaging.

Any recommendations on what/how to check, as I'm losing a lot of water it is needing to be filled up daily, i have used steel seal to repair the gasket, and have replaced a pipe which looked to be leaking. There are know no visible leaks. I have now topped up with water and gone on some test drives and it is still running out in the tank. needing to be filled up. Any ideas?

@TheMissingBolt

Жыл бұрын

Do you see anything similar to smoke or steam coming out the tailpipe when the engine is running? If you're loosing water but there is no visible leak or puddle underneath the car, then most likely your head gasket has failed and water gets into the cylinders. You can confirm this yourself or at a garage with an endoscopic camera: remove all spark plugs and check the state of each cylinder and piston. If the spark plugs appear very clean at the tip or if the cylinders / pistons show signs of rust, then you 100 % have water entering the combustion chamber.

@lukerobinson7915

Жыл бұрын

@@TheMissingBolt thanks, I used some liquid to try fix the head gasket as I was recommend by someone (steel seal). But I also took it to the garage and they said it was a leaking water pump so they fixed that and the car is up and running.

I'm driving without coolant for 3 week what should I do now

@TheMissingBolt

Жыл бұрын

How are you driving without coolant? Are you using just plain water?

Why you didn't remove the coolant temperature sensors and let the old coolant out underneath the engine? Seems like without this it is only half job done.

@TheMissingBolt

2 жыл бұрын

As far as I know, the 1.4 engine has the coolant temperature sensor near the top-right side (as you're looking from inside the car) and higher than the coolant (water) pump. So removing it would not have helped too much with the removal of the coolant from the engine block itself. This engine also does not have a dedicated coolant drain plug at the bottom, as some other engines do. And you're right, if you just do a single coolant change via the radiator drain, you are doing only half the job since you're only removing half the coolant. But I did post another video where I did a full coolant flush on the same car.

@drewsmith6066

Жыл бұрын

@@TheMissingBolt Your right chap

The operating temperature of the Vauxhall corsa is higher than most brands? The tech at vauxhall said even 110f is within spec?

@TheMissingBolt

Жыл бұрын

110 F is about 43 C, so maybe you meant 110 C? Personally, I've never reached that high a temperature in our Corsa, but I was monitoring my coolant temperature at some point in the past and noticed that it reached a maximum of about 107 C before dropping down a bit and stabilizing at about 93 - 97 C.

@justluke8836

Жыл бұрын

@@TheMissingBolt yeah sorry thats what i meant, hers goes up to 110 then the fan kicks in takes it down until it creeps up again. Apparently according to vauxhall thats correct, what reg is yours?

@TheMissingBolt

Жыл бұрын

@@justluke8836 First registration for our Corsa was May 2014, which I think makes it a 14 plate if I'm not mistaken (we don't use the plate system in Romania).

you earn sub

@TheMissingBolt

3 жыл бұрын

Thank you very much!

How you removed the metal clips from the hose. Needs it a special tool?

@TheMissingBolt

Жыл бұрын

Good question 😀 I don't remember exactly how I removed that clip, but I definitely didn't have any special tools at that time. It's possible that I used a pipe wrench because of its large opening.

@JHinterl

Жыл бұрын

@@TheMissingBolt thanks for your answer. and thanks for the video 😊

Your water pump don't leak after 4-8 weeks ?

@TheMissingBolt

2 жыл бұрын

Nope, not at all. It’s been 9 months since the change and the coolant level did not drop. Look at the oil change video from a few weeks ago. The coolant level is spot on and I didn’t have to top it off.

Hello, is opel corsa D 2014 have a problem in thermostat?if there is how I can fix it? By ECM programming or other method?

@TheMissingBolt

2 жыл бұрын

I don't know of any inherent thermostat problems on the Corsa D. What symptoms are you experiencing?

@rabahboub7572

2 жыл бұрын

@@TheMissingBolt thermostat stay open, and when I taken it to mechanecian he change temperature sensor, then the thermostat stay open now

@TheMissingBolt

2 жыл бұрын

​ What is the age of your current thermostat? If the thermostat is old, maybe it's just time to have it replaced.

@rabahboub7572

2 жыл бұрын

@@TheMissingBolt it is 3 years, but I change it and the problem staying

@TheMissingBolt

2 жыл бұрын

@@rabahboub7572 Do you have any error lights on the dashboard? Did you check the car with an OBD2 diagnostic tool? Maybe there are some codes stored that may point you in the right direction...

Did it air during changing ?

@TheMissingBolt

3 жыл бұрын

Not sure what you mean. When you drain the coolant, you're definitely introducing air into the system (it takes the place of the old coolant). When you pour the new coolant, air pockets inevitably get formed inside. But once you start the engine and squeeze the pipes as I showed, the air is eventually bled out. It may take a few hours of driving to bleed out the entire amount of air, that's why is a good idea to check the coolant level for several days after you've replaced it.

@alicankaradeniz1468

3 жыл бұрын

@@TheMissingBolt yes I had wanted ask it. Thanks for replied.

Здравей. Още ли държиш корсата?

@TheMissingBolt

2 ай бұрын

Здравейте. Да, все още имаме колата. Ще сменям съединителя и после искаме да го продадем.

Nu e ca la Dacia 1300, datul căldurii la maxim nu are niciun efect, tot la fel circula antigelul prin radiatorul din interiorul masinii. În rest e ok tutorialul, îmi place modul de realizare, felicitări!

@TheMissingBolt

Жыл бұрын

Multumesc mult! Da, asa este, am verificat si eu recent ca nu exista nicio valva de oprire a lichidului de racire prin radiatorul din habitaclu. Dar la momentul in care am facut filmul nu verificasem asta si am considerat ca e mai bine sa merg pe varianta sigura - aceea de a porni caldura la maxim chiar daca era posibil ca asta sa nu aiba efect in inlocuirea lichidului de racire.

For cleaning the cooling system....take 4 to five tablets of dish washer cleaner, solubed in water, add it to the cooling system...go with it for some days...the hotter and longer the system gets in normal operation, the better...flush thoroughly until you don't have a soapy feeling between the fingers....

@TheMissingBolt

2 ай бұрын

That's somewhat similar to the coolant cleaning solution I've used in the flushing video. Though from my experience so far, I doubt these solution make any positive difference.

Français

@TheMissingBolt

Жыл бұрын

Je suis désolé, je ne parle pas français.

ou se trouve moteur.opel.corsa

@TheMissingBolt

Жыл бұрын

Je ne comprends pas la question.