DIY Stainless Steel Exhaust tip Make an exhaust tip like this at home, without any special tools. All you need from tools are a welder and an angle grinder.
Жүктеу.....
Пікірлер: 41
@azharsalim2028Ай бұрын
Great job... however, in the first part of the laying out process, he need not take the trouble to calculate all those "pies" etc.... just take a piece of paper and wrap it around the pipe and mark the circumferemce. Then just divide it by the number you want.
@irvingcobian
Ай бұрын
Good info!
@berndheiden7630
21 күн бұрын
Easier: just fold the paper 3 times in half to get the 8 stripes!! 2/2, 4/4 and 8/8! No calculation at all!
@protomanialabАй бұрын
You are a wizard 🧙🏻♂ This is a good lesson of mechanical handicraft! Thank you friend!
@jean-pierrepannierdesrivie4406Ай бұрын
You are a very good teacher !!! Bravo !
@tonimerklin122Ай бұрын
Thank you for your videos and knowledge!
@guytech7310Ай бұрын
Pretty Neat method. Thanks for sharing!
@JoliettesParadiseAdventures29 күн бұрын
Looking great!
@arneminderman3770Ай бұрын
Wow! ❤❤ great video
@muhammadalfin2891Ай бұрын
Very neat workmanship, greetings from Indonesia
@thedude586929 күн бұрын
Nice job !!
@Rainer1992Ай бұрын
Das sind einfach skills Wahnsinn ❤
@user-rp6sv2hx5sАй бұрын
👍 super Video 👍 thank you
@michelbalts6064Ай бұрын
Magnifique....merci
@charlescamilleri3323Ай бұрын
Very nice and prof. job weldone
@stiefbeen2223 күн бұрын
Another approach could have been using a cone of cardboard, like kids have on their head on their birthday. Using the larger diameter as the base and the smaller one up as high as the length you want between the 2 pipes. Cut it at that point horizontally and use the lower part on the stainless steel. Only welds will be on each end and the closing. Less welding, less polishing.
@moarif913929 күн бұрын
that's awesome
@RustyInventions-wz6ir28 күн бұрын
Nice work. I’m sure I’ll have to do it myself at some stage
@GPGarage1
27 күн бұрын
Thanks
@nickmarshall919224 күн бұрын
Excellent work Not perfect But still excellent 👍👍👍
@kevinsmith3935Ай бұрын
Lovely bit of work , what are the discs you used on the angel grinder to clean welds and Polish the stainless please
@GPGarage1
Ай бұрын
Thanks, for cleaning the welds I use Pferd Polifan A40 SG, after that sanding discs p80, p150 and p240 than polishing with some "no name" stainless polishing kit (polishing pad and blue compound)
@dimashilov8139Ай бұрын
видео немного затянуто, но познавательно 👍
@oliverstaudinger500325 күн бұрын
Genial Einfach=Einfach Genial
@user-hg4bk7ok4oАй бұрын
Красиво. Но почему без поддува?
@luigiesposito454325 күн бұрын
Belloooooo❤❤❤❤
@sebf222627 күн бұрын
👍
@Unboxing.ChannelАй бұрын
😍😍😍😍😍😍😍😍
@denisyakob554622 күн бұрын
Мне понравилось
@AoW3_Dag_05Ай бұрын
🎉
@naboru1000Ай бұрын
Ну что я могу сказать? Ахуенно! Надо попробовать так же. А то я постоянно пытаюсь найти переходники для трубы в нужный мне размер!
@ianrace4066Ай бұрын
A cheap pipe expander is easier and doesn't take 8 hours of Fab and you don't need a welder.
@GPGarage1
Ай бұрын
Of course, there is an easier way to do this, but this is a DIY project that anyone with a welder can do. Also in this case the difference in pipe diameter is 30mm, so cheap pipe expanders would hardly do the job.
@chipcity301627 күн бұрын
Ebay $5
@MasterPKW25 күн бұрын
А то что заржавеет через полчаса никого не смущает?
@GPGarage1
25 күн бұрын
No, it won't.
@mrmiron493615 күн бұрын
По ходу чел не в курсе, что 1 клетка равна пяти мм 😅😅😅
@cecilandrews7479Ай бұрын
In the time it took you just to do the math I ordered two for $9 each stainless steel. My labor loans worth more than that
@hellkell8693
29 күн бұрын
So what.
@brianfreeman3676
3 күн бұрын
It's about using tools and fabrication. There's going to be a time when the part you want isn't available on line, what do you do now?
Пікірлер: 41
Great job... however, in the first part of the laying out process, he need not take the trouble to calculate all those "pies" etc.... just take a piece of paper and wrap it around the pipe and mark the circumferemce. Then just divide it by the number you want.
@irvingcobian
Ай бұрын
Good info!
@berndheiden7630
21 күн бұрын
Easier: just fold the paper 3 times in half to get the 8 stripes!! 2/2, 4/4 and 8/8! No calculation at all!
You are a wizard 🧙🏻♂ This is a good lesson of mechanical handicraft! Thank you friend!
You are a very good teacher !!! Bravo !
Thank you for your videos and knowledge!
Pretty Neat method. Thanks for sharing!
Looking great!
Wow! ❤❤ great video
Very neat workmanship, greetings from Indonesia
Nice job !!
Das sind einfach skills Wahnsinn ❤
👍 super Video 👍 thank you
Magnifique....merci
Very nice and prof. job weldone
Another approach could have been using a cone of cardboard, like kids have on their head on their birthday. Using the larger diameter as the base and the smaller one up as high as the length you want between the 2 pipes. Cut it at that point horizontally and use the lower part on the stainless steel. Only welds will be on each end and the closing. Less welding, less polishing.
that's awesome
Nice work. I’m sure I’ll have to do it myself at some stage
@GPGarage1
27 күн бұрын
Thanks
Excellent work Not perfect But still excellent 👍👍👍
Lovely bit of work , what are the discs you used on the angel grinder to clean welds and Polish the stainless please
@GPGarage1
Ай бұрын
Thanks, for cleaning the welds I use Pferd Polifan A40 SG, after that sanding discs p80, p150 and p240 than polishing with some "no name" stainless polishing kit (polishing pad and blue compound)
видео немного затянуто, но познавательно 👍
Genial Einfach=Einfach Genial
Красиво. Но почему без поддува?
Belloooooo❤❤❤❤
👍
😍😍😍😍😍😍😍😍
Мне понравилось
🎉
Ну что я могу сказать? Ахуенно! Надо попробовать так же. А то я постоянно пытаюсь найти переходники для трубы в нужный мне размер!
A cheap pipe expander is easier and doesn't take 8 hours of Fab and you don't need a welder.
@GPGarage1
Ай бұрын
Of course, there is an easier way to do this, but this is a DIY project that anyone with a welder can do. Also in this case the difference in pipe diameter is 30mm, so cheap pipe expanders would hardly do the job.
Ebay $5
А то что заржавеет через полчаса никого не смущает?
@GPGarage1
25 күн бұрын
No, it won't.
По ходу чел не в курсе, что 1 клетка равна пяти мм 😅😅😅
In the time it took you just to do the math I ordered two for $9 each stainless steel. My labor loans worth more than that
@hellkell8693
29 күн бұрын
So what.
@brianfreeman3676
3 күн бұрын
It's about using tools and fabrication. There's going to be a time when the part you want isn't available on line, what do you do now?