Amazing how to video. So good infact that I was able to repair the dishwasher without any issues whatsoever. Thank you, thank you, thank you for this most informative instructional video 👍👍

Thank you, straightforward and very informative.

@repairclinic

5 ай бұрын

You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!

Thanks! This totally helped me fix my DW

If you replace the element and/or the thermostat you should then do a diagnostic test to reset the machine. I replaced mine and it still did not work until I did the test. On my machine (whirlpool) you use any three buttons and press 1-2-3/1-2-3-/1-2-3, quickly. my machine works now that I did the test.

@repairclinic

9 жыл бұрын

Rick C Great. Thanks for sharing about your particular experience!

@andrewrayjones

8 жыл бұрын

+Rick C Thank you Rick! The same thing happened to me. I couldn't find anything about this in the manual, so without this comment I would have been lost. I also ran the machine on "Sensor" setting after this test, which I hadn't been doing before. I don't know what difference that made...probably none, but I think my Whirlpool has an optical sensor thermostat, so it may be related somehow.

@SteveThatsMe

6 жыл бұрын

Rick you rock I did the same thing. Replaced the element not heat. Then the thermostat, still no heat. Thank God you left this tip. Ran the diagnostic test and it all works. Thanks again

@andyd6695

6 жыл бұрын

Thank goodness your post stayed up for 3 yrs. RIck, I never would have gotten my dishwasher to work without your post! Thanks so much, you saved me many gray hairs!!!

@thejourneymen7722

5 жыл бұрын

Thank goodness I ran cross this video with your comment about doing a diagnostic reset my dishwasher quit drying dishes last week and after watching numerous videos I determined it was the heating element that was bad so I replaced it in the dishwasher still did not dry dishes. But after reading your comment and resetting the dishwasher by doing a diagnostic test dishwasher is working like new and all is well.

hi there. i have an ikea rengora dishwasher not heating up. looked for the heater. is the heater in the motor?

Thanks for making this movie!!!!!

It needs to be isolated from the other parts of the dishwasher and you need to have access to the terminals. It is easiest to take the element out of the dishwasher.

Hi. I just checked the continuity of a Flow-Through Heating element. I found the reading above 100 ohms following the instructions of the video. Would that suppose a different issue?

Hello. My multimeter only has the X1K setting; and not the X10 as shown in your video. When using X1K, i get no movement in the needle whatsoever. Can I assume the heating element is bad while using the X1K setting?

I would recommend using the repair help section of our website (link in the description). If you enter your model number there you'll have access to part, model and symptom specific repair help.

Can you check this without pulling out the heating element?

New repairmen nowadays, What’s analog? What’s that needle thingy? 😂😂😂 Great info, thanks.

@repairclinic

7 ай бұрын

You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!

Hi haw ary you dishwashir broblam DLC module DWA3320 error F5 thanks

Exactly Where can you find this Heating element in the dishwater??

@rhikdavis

Жыл бұрын

At the bottom...it looks like the heating element in a oven...

can the heating element just be lifted out? whirlpool.

@repairclinic

10 жыл бұрын

No. It is connected to the dishwasher is a couple different places. We would need your model number to give specific instructions.

@jeffmarsh4518

10 жыл бұрын

Quiet partner ll

So these things should have about 10 ohms of resistance?

@repairclinic

10 жыл бұрын

The resistance will vary a little. You may see 20 or 50 depending on the element. If it shows a resistance reading that is close to that the element is good.

@pjuice2000

8 жыл бұрын

+RepairClinic.com what about 12 ohms? is it going bad?

When testing for continuity, why not just do a continuity test with the multimeter? Pardon my ignorance, I don't understand why it is better to test for resistance in this particular case. Thanks!

@brucetec6597

3 жыл бұрын

Those are multimeters

Mine was 16.7 oms. Is it bad.

@pheth1302

5 жыл бұрын

16.7 ohms is good but make sure you're not on K (kilo) or M (Meg) ohms, otherwise it is bad.

14.4 and still not drying. Suggestions?

@Buzz1151

7 жыл бұрын

relay on the control board