Dieselgeek MK6 Super Pin and First Gear Getter Combo Comprehensive Installation
Автокөліктер мен көлік құралдары
Tyler goes in depth while rebuilding the shifter box found in all 2008+ VW MK5 and MK6 vehicles using the Dieselgeek MK6 Super Pin Shifter Bushing kit linked below!
dieselgeek.com/collections/vw...
00:00 Order of operations
00:31 Removing the factory forward pivot
03:15 Installing the Dieselgeek Super Pin
09:52 Side to Side Cable end Bushing
11:44 First Gear Getter
Fits the following years and models with five or six speed manual transmissions:
2012 - 2014 Golf R Mk6
2008 - 2014 VW Golf and GTI (Mk5 and Mk6)
2006 - 2008 VW R32 Mk5
2008 - 2014 VW Golf and Jetta Sportwagen
2008 - 2009 VW Rabbit
2012 - 2019 VW Beetle
2008 - 2018 VW Jetta and GLI
2008 - 2019 VW Passat and CC
2009 - 2017 VW Scirocco
2007 - 2015 VW Polo (SP fits, FGG does not)
2008 - 2016 VW Eos
2008 - 2015 VW Tiguan
2008 - 2014 Audi TT, TTS, and TTRS
2008 - 2014 Audi A1, A3, A3 Cabriolet and S3
2011 - 2014 Audi Q3 and RS Q3
2008 - 2019 Seat Toledo, Leon, Ibiza, Alhambra, Altea, and Mii
2008 - 2019 Skoda Fabia, Octavia, Roomster, and Yeti
Пікірлер: 15
I am looking for this exact first gear getter (the white peice of plastic replaced by that black one) for skoda octavia and i am struggling fo find it in the UK or anywhere, please help me get one or 2 of those? Thank you
@dieselgeekdotcom
Ай бұрын
Shipping to the UK is no problem.
How deep does it need to be drilled? Just enough to remove the rivet head?
@dieselgeekdotcom
5 ай бұрын
Yes
This is cool and informative but how is it done while it's inside the car?
@dieselgeekdotcom
Ай бұрын
You have to pull the center console trim. We have a video on that.
@jimbz20
Ай бұрын
Are you letting the eboxy set in 4-6 hours or cure in 15-24?
@dieselgeekdotcom
Ай бұрын
You need to let the epoxy fully cure. You really want that drill guide to be adhered securely so that you can center drill the pin to exactly 5/16.
@jimbz20
Ай бұрын
And how long after can you drive the car with the epoxy going in the first gear getter?
@dieselgeekdotcom
Ай бұрын
After it fully cures. It's really all there in the video.
Why not just center punch it before drilling it?
@dieselgeekdotcom
9 ай бұрын
The 5/16 inch hole must be perfectly on center and on axis with the pin. This is best accomplished using a fixture, hence we supply the drill guide.
@rickysparks534
5 ай бұрын
@dieselgeekdotcom so no need to drill in to the bell crank also? Thanks for getting back
@dieselgeekdotcom
5 ай бұрын
You need to drill it using the drill guide and the 5/16 in drill bit until the bell crank releases EXACTLY as we show in the video.