Thank you ! I’ve had my Chinese heater for a year now. I was sceptical at first. Having had so much trouble with my Webasto I figured it was worth a shot even if I ended up buying a new one every year. At half the price of having my webasto serviced once every three months. I recently decided to buy the LCD monitor and remote. Upon plugging it in I received code 01 and my immediate response was to curse at great length about why I messed with something that had worked so well. You video solved my issue right away.

Hello from a thankful diesel user. I just got the unit and have the same problem. YOU have been the BEST web site with the EASIEST instructions. Again Thanks

@peterjohndesmond369

4 жыл бұрын

HeEhyehAsherEhyehNOW your welcome and happy it helped you I realise it’s not the best video it’s not what I do , just wanted to help others with same problem

Had a basic controller, plugged in this controller, same problem. I was racking my brain looking for wiring faults. THANK YOU!!!

Thank you so much from freezing 🥶 trucker. Hello from USA 🇺🇸

@peterjohndesmond369

4 жыл бұрын

Your welcome be safe hello from australia

Thanks for taking the time to help out when these errors come up - you have been a great help

@peterjohndesmond369

3 жыл бұрын

No worries ,I bought a couple spare glow plugs as they are hard to get when your out on the road .You will need a tube spanner that will need modifying to get the plug out .Plenty of you tube videos to explain how to do it

Champion!! Thank you for this video. I search everywhere and you solved my problems really simply👍 mine was in 24v mode and showing error 01

You sir are an absolute legend and a gentleman. Thanks for taking the time to post this. Obviously really bloody helped me out 👍🏻👍🏻👍🏻

@peterjohndesmond369

4 жыл бұрын

alex hallett your welcome mate

@akbariw

4 жыл бұрын

I saw so many videos so much time wasted and new it had to be voltage setting but couldn't get to it.

Thank you very much I will try this tomorrow I have had Enough for two days thanks so much for people like you

Good sir, you just saved me a big headache. Thank you.

@peterjohndesmond369

Жыл бұрын

Your welcome

Thanks for the admin code mine was set at 24 volts after replacement of the controller now back to 12 volt for E-01 fault code that's the solution.

Super thanks fixed it, as winter upon us soon.

Thanks man. Life saver. How did you find that code? 1688?

Hello there , I am after some help with a new 5kw diesel heater , I have installed it today & a E07 code has came up on the control panel , The manual that came with the heater is telling me code E07 is a Disconnection fault , Check whether the communication line or plug Between the switch & the controller is open or falsely connected . I am not 100 % sure what that means so I have undone all plugs & sprayed with WD40 & made sure all plugs click back together as they should , But so far still no luck getting rid of this fault code & getting the heater working .

Man you are a life saver.

I had the same error code after this fix. Started my van engine to put more power into the leisure battery via my DC to DC charger and the heater started up with no issues. Thank you for sharing. Keep safe Si

Thanks buddy i was ready to change my bunck heater and you video saved my money

Thank you brother!!!!! Big help

You Sir, are a legend!

Cheers buddy your a legend 😍👍🏽😎

Thank you mister, you saved my nervs! :)))

Thank you.

Error 01 flashing battery is shorten your live wire to the battery and or replace for a thicker 6mm cable

*You Rock PJ !* Liked/Subscribed

Golden and a quick fix!

Thanks for the info 🙂

Yes thanks my is sorted now

Yep thanks that helped me out. Simple quick easy! But mine then went to error code E-03!?

What do the blue bars mean in the middle of the heater icon?

01 is low voltage can also happen when battery is below 10 volts or so 02 is high voltage I had this when trailer was connected to shore voltage and converter was over charging battery to 17 volts. (changed out converter now OK) 03 is glow plug 04 fuel pump fault 05 is overheat could be real, sensor or fan too slow 06 is motor fault could be magnet or hall sensor (little wires sticking out of mother board near fan0 07 is comm fault check blue wire 08 is flame out could be fuel line (air or dirt) temp sensor

@charlieswearingen500

2 жыл бұрын

Thank You...

E00 - NO ERROR E01 - Under voltage - your battery does not have enough power, please recharge. E02 - Over voltage - Voltage is over the permitted level, reduce voltage to 12v. E03 - Glow plug fault. Check leads and replace if necessary. Can be low voltage. E04 - Fuel pump disconnected. Check lead to fuel pump, check connector is clicked in place. Can be low voltage. E05 - Overheat. Check air intake is not restricted at rear of heater, check fan is not impeded. Ensure that the installed heat vent is not blocked / restricted. Also check that heating duct has not been crushed, thus restricting air flow. Callouts for restricted air flow or crushed ducting will be chargeable as follows £60 call out fee plus £39 per hour/ part hour over 30 mins on site. Plus any required replacement parts. E06 - Fan motor fault - Normally caused by low voltage. E07 - Communication between controller and heater broken, check lead and connection plug. Again can be low voltage. E08 - Low fuel or air in fuel lines - refuel vehicle, check fuel filter is full. Can be low voltage. E10 - One or more of the above error codes and the unit has been restarted a number of times without success.

@lourdespagan6045

3 жыл бұрын

The heater had 02 code batt icon blinking ,went in to program changed from 12v to 24v was using transformer .using unit to heat small car port ,is it better to utilize 12v , hooked up car battery and unit didn’t power up any help out here ! Thanks 😒🤓

@beroliman

3 жыл бұрын

@@lourdespagan6045 Don't use voltage converter, use the system voltage directly! At start the device draws large current, that the converter cannot give. If your vehicle has 12V system (cars, vans, small motorhomes), use 12V in controller, if it has 24V (buses, trucks), use 24V. If you have one battery, and receive the e02 error message, check the voltage with a voltage meter. The device works in my van without error from 11.8 up to 14,5 Volts.

@brucebourget9508

2 жыл бұрын

I myself got the e06 error and it all started whith battery was low . Round one I had no fan checked wires tryed spinning the fan, after it shut down turned fine no rubbing but no pump or fan shut down error06 round two fan started working, after checking wires to battery an gave the fan a spin it started working the fan sped up then checking the voltage wile the fan started noticed battery on controller was blinking and volts was all over down to 8 volts, bouncing around but no fuel pump sound clicking then shutdown again. but checked wires on battery volts said it was fine herd the pump. On third time around But i could barely hear the pump . I still got error 06 code I'm going to say my battery voltage was the start to this problem . Hope some of this helps someone I'm guessing I'm going to have to change my voltage on the heater . I will update when I fix the problem. Thank you for error code fix going to try that next.

I have the same issue but i can’t get on to my settings.. when I press the settings button it only cycles between temp and fan speed

Hi, Just wondering if you can still give advice on this E01 error code. I get to put the code in, but it will not let me get away from putting in the numbers, any ideas ?

Good afternoon. I bought two spark plugs and did the exchange procedure with both. When turning on the heater, the candle does not glow. What should I do? Thank you for your help.

Yes it does help to start it up, but then shuts down again. Low battery it's saying, but battery's are fine ????

I tried to lower the temperature to 0.9 hz, but after a while I get error 08. Is it because it is set too far below the minimum?

MERCI 😉

Hope this works... ...yup, took two tries, but it worked! 😃

I love you. 😂

im getting this even on the 12v setting...

I bought on and it started with e 01 error and now its e03. Ill try this

Still getting same error after code input, any ideas ?

@petergeen2198

3 жыл бұрын

My 12 volts supply comes via an inverter and voltage sometimes drops on startup, by clicking 'OK' till voltage shows on screen at start up you will soon know. The issue seems to arise around 8.5volts. I have my P-set to P-1.3Kh I find this helps.

Were do u get these codes from. Cheers

Same problem here. How did you get that info and code to put in?

@CoherentChimp

4 жыл бұрын

Type "diesel heater error codes' into Google. See what it comes up with.

@petedebo6906

4 жыл бұрын

There also another code 9009 :)

@deboraharnold2349

3 жыл бұрын

We are on 12 volts but still getting and heater comes on then turns off help

Mine eas on 12v but i have the same eror

I. O. U a beer .Cheers

Hello any idea for E 8?

@jasonhalbert8279

4 жыл бұрын

I have the same E8 code ? Fails on start up. Im thinking its a 12v issue the battery is at 10v and drops as the machine try's to fire up. The internals are clean

Had a friend translate I Chinese you tube video

E oo? Can't turn it off.

E10 error ?

many thanks so simple

What is error code e02

@Bakboun

2 жыл бұрын

Overvoltage power source

Hello, that only fixes the error if you had changed the heater from 12 v to 24v.. or the other way around.. I have that code and it's on the same 12 v supply since purchase. These heaters are more trouble than they are worth. Constant trouble with it.. despite only being 8 months old. and used 4 times ... It swallows diesel.. and the heat output is minimal