I really not like to write comments , but I want to thank you about the information it’s really very helpful I have problem my machine gives me a code ( DHE ) and my mother got upset and when I seen your video and you explain make it very easy I opened the machine and I saw the yellow wire pend and go out a little so I plug it and correct the pend and know its work as nothing’s happened and my mother very happy ❤😂

Thanks a lot, this really the cause for my combo washer/dryer showing 'dhe' error code. Can't imagine having LG technician to come only to reconnect the wire pin.

Thanks for sharing! Unfortunately it wasn’t just the cables on my machine. But I did hear a clicking sounds inside the fan, so I opened it up, cleaned it free from lint, and now it works perfectly.

AMAZING Never thought I could fix my washer and I did. Thank you sir

Well, it is a good tutorial. It encouraged me to open up my machine and look for the problem. And it was problem related to a cable. The fan wasn't working properly because the cable was broken. It looked like it was a bad design of the part that was holding the cable together with the fan. It was so tight that it kinda cut two of three wires used by the fan. The fix was easy, though, as the cable was visibly damaged.

Thank you! Fixed the problem!

Very informative and helpful video

Excellent simple video steps, thanks.

@askmrwashywashy

2 жыл бұрын

Welcome glad it helps

Thanks, Dear. It works for me.

I noticed that the wires going into the white part are cut off, and I don’t know what to do to replace it. I know how to change wires, but how do I get a new part ? Cause it seems really difficult to keep the same one and reuse it. My washer is quite old, and so are the parts.

Thank you, mine had the first issue of a connection coming loose. Simple fix!

@askmrwashywashy

8 ай бұрын

Glad it helped

It works again! Thank you sir 🙏🏻🙏🏻🙏🏻

@khaled6100

Жыл бұрын

Nope , the DHE error comes back again 😖

thankyou this 100% works

Sir, very appreciated! I actually fixed it~

Hi, thanks for your video. My unit gets hot, but it suddenly stops and I get the dhe error. Any suggestions?

I had the DHE error but it was because every screw holding down the heating element and the blower motor backed out from vibration and fell to the bottom of the washer. I placed it back on and installed a few of the screws including and the heating element got hot. I purchased new screws, a new condensation tube and replaced. I ran one cycle and the heating element no longer gets hot. There are no loose wires. What could be the issue?

thx... seeing this i decided to open mine. the wires were not broken. i opened up the fan. and it was full of dirt. now it spins again and works. the problem i had in the past is that the cooling down took so long

@askmrwashywashy

2 жыл бұрын

awesome glad you fixed it

@AngelinaSaysfckit

4 ай бұрын

How do you open the fan?

Thanks bud. 👏🏼🇧🇷

Thank you!

@askmrwashywashy

9 ай бұрын

You're welcome!

So, why would that wire had gotten loose?

The video has been extremely helpful. Thank you. In addition to fault finding. If everything seems fine, I found my heat sensors both input and output to have had dirty. They are situated, first one under the fan(looks like a pin) and second one is at the down pipe after the heat element. Clean them. Cause of dirt was - a blocked water pipe filter that lead to water not cleaning the air tank below, which lead to dirt building up and the fan pulls dirty air through the duct. Bottom line, regularly clean the inlet water filter to avoid. Pressure clean the bottom tank and open the drain in front of the machine while doing cleaning. Regards

@bentleyemmett7656

2 жыл бұрын

You probably dont give a damn but does someone know of a way to get back into an Instagram account?? I was dumb forgot my password. I would love any assistance you can give me

@justicepatrick6366

2 жыл бұрын

@Bentley Emmett instablaster =)

@bentleyemmett7656

2 жыл бұрын

@Justice Patrick Thanks so much for your reply. I found the site through google and I'm waiting for the hacking stuff now. Seems to take quite some time so I will get back to you later when my account password hopefully is recovered.

@bentleyemmett7656

2 жыл бұрын

@Justice Patrick It did the trick and I finally got access to my account again. I'm so happy:D Thank you so much you saved my ass!

@justicepatrick6366

2 жыл бұрын

@Bentley Emmett No problem xD

Hi! Thanks for the video. DHE error could be caused due to dirtiness of the fan or the heating element? Maybe caused by quality or excess of detergent

Wires were all good on mine, so I checked the fan. Lint had collected on some of the fins, causing it to spin awkwardly. I cleaned the fan and all is good.

@Xxatanaz

4 ай бұрын

Did you just unscrew it from the top? Looks like I’m gonna have to do that since my wires are all good my

We get the error within moments of the dryer cycle starting. All the connections look good. You can feel the black part is starting to get hot even in the short time the element is on and blowing so the element is not the culprit. Other suggestions?

@askmrwashywashy

3 жыл бұрын

hi i think there is a broken wire so what is happening is that current is passing enough for it to start but when its under load heating up more it triggers the error to say there is a worn wire somewhere. I would suggest tracing the heating element wires in the wire loom at the back where it bends after coming from the heater there will be a break there

The blower fan on my unit spins up but stops a second after ramping up speed and cycles a few times. The wiring looks pristine. Dead blower motor?

@askmrwashywashy

2 жыл бұрын

Does it heat up ? It’s likely the problem with heating element.

@mikeely8468

5 ай бұрын

Do the fan blades have any lint collected on them?

Hi been having so many issues with this combo not drying it washed fine but I put it on 30 min dry it slightly tries to spin and then the dhe error code comes on no idea what to do is there anyway you can make another video regarding that had the heating wire replaced already. Fans cleaned. It gets hot too.

@maroiro

Жыл бұрын

have you fixed your combo? I have the same problem..

@Momo564732

Жыл бұрын

@@maroiro no and the handy guys couldn’t figure it out either

@maroiro

Жыл бұрын

@@Momo564732 omg we fixed it yesterday! our thin wire that goes into the fan was worn and cut. It was wrapped in the white fabric protector so we had to cut it to check. Our fan was also not working so we had to replace it. Hope you can also find the problem.

@Momo564732

Жыл бұрын

@@maroiro nothing was wrong with the fan, but I think it’s some wiring

I have the WM3477HW 24” washer/dryer all-in-one. dHE code started coming recently. Dry cycle would go for 6-7 minutes and then stop. It has happened 15-20 times. I then tried turning off the water supply valves and coincidentally the dHE code no longer displays. Clothes come out dry. However, I decided to do a dry cycle with the water supply valves on again and the dHE code came up once again. Any ideas?

@askmrwashywashy

2 жыл бұрын

usually DHE is the heating element wire thats faulty. From what you are saying try might be the three way water valve. Check it like this. Remove the top cover of the washer. UNPLUG THE WASHER. On the cold water valve there will be three electrical connectors. Disconnect the one that is closest to the dryer. Usually it has a black hose going from it to the dryer. Open the water supply and start a dry cycle. If the fault doesn't return the three way water valve is faulty

Is there a reset button on the thermostat ?

@askmrwashywashy

2 жыл бұрын

Hi no reset button on there it usually resets itself

We have a twin washer dryer combo, and it keeps coming up with the DHE error when the dryer cycle starts?? We have replaced the heating element... do you have any ideas on how to fix this error??

@askmrwashywashy

3 жыл бұрын

Hi what is your model number ?

@damienbugler8950

3 жыл бұрын

@@askmrwashywashy WD1216HTE

DHE error comes after few minutes of heating starts then switch off restart and again DHE error but heater and wiring is ok what will be the fault pls reply

@askmrwashywashy

2 жыл бұрын

Hi mate I’d say wiring might have high resistance. Check your heating wires around bends

What is lev problem?

@askmrwashywashy

Жыл бұрын

le is an error with rotor position sensor. You will need to change the rotor position sensor or on some newer models its now part of the motherboard

When is video coming of the Samsung autodose please

@askmrwashywashy

3 жыл бұрын

Hi I just got the washing machine delivered today so I’ll record something for you over the weekend

@tracyconnor4139

3 жыл бұрын

@@askmrwashywashy could you do a unboxing video

@tracyconnor4139

3 жыл бұрын

@@askmrwashywashy can’t you record the unboxing and installing of machine and upload tomorrow

@askmrwashywashy

3 жыл бұрын

Sure I’ll do that

@tracyconnor4139

3 жыл бұрын

@@askmrwashywashy thank u so much when will. Video be up

Fix starts at 2:17

You dont use nor mention test meters huh?

@askmrwashywashy

2 жыл бұрын

don't need to. been fixing these a long time

@tsvina

2 жыл бұрын

@@askmrwashywashy cowboy 🤠

Too much talk