do you know what eot and pst means? thanks

@How-to-repair

2 жыл бұрын

HELP NEEDED!! not at the moment but i will pin this to the top of page so some helpful samung engineer might give us the answer

@mattbandura9015

2 жыл бұрын

DARK GARMENT : Washing Motor Work Test (“PSt”) *check water level

@mattbandura9015

2 жыл бұрын

OUTDOOR CARE : EEPROM Test (Eok : OK, Eng : NG)

@mattbandura9015

2 жыл бұрын

B. The Sensor & Motor can be tested when you rotate the course encoder.​ - COTTON : Micom Software Code check​ - SUPER ECO WASH : Model Option Check ​ - BEDDING : Water Level Frequency (ex. 242 -> 24.20kHz)​ - DAILY WASH : Water Temperature (ex. 254 -> 25.4℃) - DELICATES : Air Temperature (ex. 300 -> 30.0 ℃) *not used​ - BABY CARE : Duct Temperature (ex. 300 -> 30.0 ℃) *not used​ - OUTDOOR CARE : EEPROM Test (Eok : OK, Eng : NG)​ - DARK GARMENT : Washing Motor Work Test (“PSt”) *check water level​ - ECO DRUM CLEAN : Washing Motor Work Test (“tst”)​ - RINSE+SPIN : Spin Motor Work Test (“SPN” , move to MAX RPM)

@How-to-repair

2 жыл бұрын

thank you so much for assisting i learned something today thank you

I'm watching from Jamaica 🇯🇲. Very helpful.

Thanks for this demo my machine stopped working after a power cut while mid cycle and would not turn on to any new program after. After running through the test program as you demonstrated it worked perfect again.

Best Samsung washing machine video, thank you soooooo much!

Excellent. Clear and Concise. Thank you !

Very well explained, thank you for the great video.

I am a pharmacist. My w.machine has drainage problems, and drain pump stucked by rust/waste particles. I have test it by test mode, identifying problems and clean the pump. The machine is fully ok now. Thanaks for your Videos.

You are wonderful. Thank you for your thoroughness.

@How-to-repair

Жыл бұрын

Really glad it helped you fix your problem Thank you for leaving a comment this is for you kzread.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

This video is legendary!!! Extremely helpful!! Thank you so much! ❤

Thank you so much - the video is very useful! Every step is well explained so it is very easy to follow the instructions.

@How-to-repair

Жыл бұрын

Glad it was helpful! Thank you for leaving a comment this is for you kzread.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

This video is absolutely fantastic, thank-you so much

Thank you very, very much from Paris. Because of your chrystal clear explanations, I was able to diagnose the washer motor was not working, which led me to a faulty connector on the front panel. Works like a charm now.

Just to say thanks for the info, just saved me buying another washing machine very good and easy to follow, solved at the moment and seems all working fine.

@How-to-repair

3 ай бұрын

I'm glad I was able to help you just remember to Mark us down to your favourites. As you will never know when an appliance fails it also helps us a lot, if you can share the channel @dennisbentley9242 please remember to subscribe to our channel as that really helps us kzread.infoe432SAb2g08 Thanks, Paul 👍

Excellent detail - thanks

@How-to-repair

Жыл бұрын

Thank you for leaving a comment, I would love you to leave your opinion on our poll about manufactures building in obsolescence to appliances. kzread.infoUgkxygHomnUySd_bYjaJBdEHPO6T4dYo9Ahm and this is for you kzread.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

Thanks, followed ur instructions, comes up on fault.

Thank you very Mach, good explanation.

Great, very informative, many thanks.

Great video thanks!!!

Thank you so much your video it's very helpful 👍👍

@How-to-repair

Жыл бұрын

You're welcome! I'm glad it was helpful. glad we could help you @singh2007mahendra this is for you kzread.infoe432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍

Amazing tutorial sir. Best video I have ever seen, very thorough and knowledgeable about the tasks that you are explaining. Well done, sir.

@How-to-repair

Жыл бұрын

Glad it was helpful! Kevin Gronemeier this is for you kzread.infoe432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍

You're simply great the way you explain things. Congratulations sir.

Excellent tutorial!!!

@How-to-repair

10 ай бұрын

Thank you! @joaocoelho7331 please remember to subscribe to our channel as that really helps us kzread.infoe432SAb2g08 Thanks, Paul 👍

Thanks you a ever so much, your video was so helpful ❤❤❤❤

@How-to-repair

Жыл бұрын

Thank you for leaving a comment, I would love you to leave your opinion on our poll about manufactures building in obsolescence to appliances. kzread.infoUgkxygHomnUySd_bYjaJBdEHPO6T4dYo9Ahm and this is for you kzread.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

Very interesting 👌

Good video, just bought a Samsung series 5 washing machine after our indesit washer/dryer broke. Samsung allegedly reliable so we shall see.

Hello sir good day to you.your video is really mind blowing. Superb.Thank you sir

Thank you very much.

thank you for this

Excellent video - very helpful - any idea how to stop or what the cause of a musty smell in an empty Samsung 8kg (2016) washing machine.

Vry useful video thnq vry much sir

@How-to-repair

Жыл бұрын

Glad it was helpful! Thank you for leaving a comment this is for you kzread.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

thank you very much that video help me to fix my machine

Very nice to know. Should do more with other brands. Thanks

@How-to-repair

Ай бұрын

I will be doing a lot more of these in the future @tommylou7169 please remember to subscribe to our channel as that really helps us kzread.infoe432SAb2g08 Thanks, Paul 👍

Thanks a lot!

@How-to-repair

Жыл бұрын

Glad it was helpful! Thank you for leaving a comment this is for you kzread.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

Hi, congratulations for your videos, very clear. I have a question for you, I have a Samsung washing machine with DC error. There is 220 volts on the door lock connector, I replaced it but it still shows the same DC error. I noticed that the 220 volt is present on the connector only when empty, i.e. without the door lock connected, if I connect the door lock the 220 volt is no longer there. What do you suggest me? I'm thinking of replacing the board, but it costs a lot and I would like to limit the risk of making a mistake.

Very good video sir.

@How-to-repair

2 жыл бұрын

Thanks and welcome Thanks 👍 for watching and please remember to subscribe to the Channel as that's what keeps us going in able to make the video for you

Good luck and success to everyone Al-Jarjawi, automatic washing machine surgeon

Hello! Thank you for your video! I have a Samsung washing machine model WW70J4463GS but it doesn't have the same buttons. From left to right, they are "temperature - spin - option - delayed end - bubble soak". Could you please tell me which ones I need to press to enter the washing machine's diagnostic test?

Great videos. Can you do this on a top loader? Mine is a 13kg, it is about 5 to 8 years old. There is no dial. Thanks!

Thanks for the informative video. I have samsung Ecobubble digital inverter ww10n645rbw. The machine is not heating up. I have checked the element and thermostat with a electrical tester and they are ok. My pcb was replaced some years ago and I swapped the current one with the original one (which was ok at time), still no heat. I have run the diagnostic test (from the delayed start proceedure) but I am not whether I hear the element coming on during the wash cycle test. The simple diagnostic test shows no error. I am at a loss. Any thoughts? Do you stock the pcb's if it that? Many thanks

@How-to-repair

18 күн бұрын

Hi David, I've created an FAQ page for you. You can find a detailed repair guide for your problem on this page. I suggest you start by getting a smart multimeter and testing the heater, NTC sensor, wiring, etc. Here is the link: www.how-to-repair.com/faqs/samsung-ww10n645rbw-washing-machine-not-heating/ Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/ 😇 Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

Wow thank you

Good luck sir 🎉

Great informative video. I have error code UC, it’s intermittent and seems to appear half way through any cycle. I haven’t been able to pin point at what point the error code appear. Any idea?

Hi just want to find out if there is a test with the washer dryer testing the dryer heating side of thing? Great video thanks

@How-to-repair

Жыл бұрын

not yet sorry Thanks please remember to subscribe as that's is was keeps this channel going. Thanks 👍

How do I run a service wash - EcoBubble 2016. Thank you

For me, it shows an error 3E2, can you specify whether it will be an inverter motor or PCB? thank you

You are awesome

Can you show how to start the manual service cycle on the Samsung WW60J4260LW?

Ty sir…

Can I do this to my Samsung washing machine Schaumaktiv 7.0kg and I don’t have ecobubble

Hi, I have a Samsung eco bubble 7kgs and I get error 4E. I have cleaned the water inlet rubber that was clogged and it is now taking water, but the error still appears. What can I do? Thanks

Thanks

Thank you . Can i also change end song in the machine?

What brand/model are the built in multimeters that you use? Thank you

@How-to-repair

Жыл бұрын

these are the digital ac 50a ammeter i use they come in many types and colours ebay.us/FC2Wgf this is an affiliate link so I will win a small commission off eBay I hope you don't mind. and this a message for leaving a comment Thank you For leaving a comment this is for you kzread.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

Loved you in aliens3 thanks. But my machine stops in spin and powers off and on forever, i took off the crappy plug splitter but now it still beeps there without finishing. Cant figure it out still. Thx

Many thanks - mine does not go to tSt when I get to the part Rotate the program Left - instead it goes through the numbers and then goes to: 4C-OE, 80_ _80, 254, then finally UC and sticks there. It’s the older non inverter model. Any ideas ? In general I have the Random Pause problem when running programs and have an occasional 3E code, but am changing brushes in the next few days.

Hi We have a Samsung eco bubble with 5E. After 50 mins on quick wash the display reads 5E so we power down and power on the machine turn it to rinse and spin it runs to the end no water in the bottom of the machine so I cleaned the filter out removed the pump all looks good but you can’t rotate the motor no more than one revolution either way not sure if that’s right re assembly tested again same thing after 50 mins 5E also learned the waste on the sink trap. Any ideas. Thanks Ray

For Australian machines it's pretty similar, only you hold buttons 2&3 when powering up

@unblackdawn1134

Жыл бұрын

On german machines too . Thanks dir the comment M8 😊

@jh45411

Жыл бұрын

Not getting any help

Hello, sir, how are you? I am Abdullah from Turkey. I am watching your video. You are a so great engineer. I have a washing machine this Samsung bubbles have a shaking notice. I sent to the some picture tell me that what happened this what problem. Thank you so much. So nice of you.

@How-to-repair

2 ай бұрын

If you upload a video to KZread, then send me the link. I will be able to look at it for you.

This is good but i have a Series 5+ ecobubble machine with the long display fascia window and i have searched ages on youtube how to perform test mode on that and no-one has done one , the 2 buttons to test dont work on my series 5+ WW90T534W washing machine so do you know the sequence for these type of Samsung washing machines or have doe a video? Thanks.

@xulissesx

Жыл бұрын

Got ? can you teach me?

@MikeCarter

Жыл бұрын

My Samsung ecobubble ww10n645rpx/eu model doesn’t appear to respond to the suggested button presses to enter diagnostic mode either. Is there a new set of buttons to press for this model?

Thank you for your explicit vids. They are for engineers? Please do you know if better instructions are available for the WF90F5E5U4X regarding the explicit operation /programming of the fabric softener? My wife has had a problem with the centre compartment (softener) always taking the fluid in prematurely. It may well be programming not set ever since 2016 since we bought the machine. Samsung say the program has been off at manufacture but she says not. I rang Samsung and the Tech said he would look at the manual! There must be more comprehensive literature because I see many others are not fully conversant with the softener application. There seems to be many unanswered questions about what seems to be a well engineered machine that lacks in data available to the users. Boilers have more comprehensive instructions for the users. This maybe because a boiler can blow you up but a washing machine no.

Hello, please advise. I have a washing machine eco bubble 7kg / wf70f5e5u4w. The washing machine began to jam, as if it did not have the strength to turn the drum. It is interesting that it could only be washed on 3 programs - hand wash, wool and spin. All three work without a prewash and it worked for a few days. Now the whole program, this short one, and the spin cycle are no longer running. I observed the washing machine and I really think that the motor runs quietly, the water fills in, the pump drains ... the fault is really mysterious. After loading the smart apps - it says ˇThe motor rotor was diagnosed as locked" So there is a question? is the problem the motor or the motherboard? Thank you very much for your opinion :-)

Note: to enter test on non ECOBubble machines, press and hold middle two buttons (Rinse & Spin) then press Power on button

Do you also have a video how to fix a LC1 error on a samsung washing machine?

@How-to-repair

Ай бұрын

hi LC or LC1, are we needed to drain pump issues? I have done lots of videos on drainage problems on washing machines. I suggest you check the pump the sump hose and also the waste fittings going to the appropriate connection that you have basically this error is saying unable to empty in the allocated period of time this is why you are getting these error codes @rodneysijp2343 please remember to subscribe to our channel as that really helps us kzread.infoe432SAb2g08 Thanks, Paul 👍

Nice vedio. my ecobubble stop in the middle of the cycle without appearing any error?

Hi quick question I have the same machine all tests are fine apart from it doesn't turn while washing spins fine tho

@How-to-repair

Жыл бұрын

It will depend on what model you have as there are different variations in motor. If you have a motor with carbon brushes, I would inspect them or if you have a motor that does not have carbon brushes then normally this will be a problem with the circuit board. Have a great New Year and please remember to subscribe to the channel. glad we could help you @anthonybaxter808 this is for you kzread.infoe432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍

our eco bubble drum seems to oscillate side to side when rotating, it moves 1/2 cm from left to right is this normal?

Hi. How do i enter test mode on the WW70TA049AE ?

Hi turning my Samsung machine on immediately the error code comes up so it will not let me put it in diagnostic mode what do I do we've put in two temperature thermostats already the error code is TE

@DrColg8

Жыл бұрын

Recalibrate after the repair and give it a try. The error memory may have to be cleared to recognize the new sensor

Thanks for this movie! When I try to enter this mode I become only " -: " sign. Does it mean the PCB error? Should it be replaced?

@How-to-repair

Жыл бұрын

Without having the washing machine in front of me, it is very hard for me to actually say with honesty, what the problem is, as I do not want you to go buying a new circuit board and finding that is not the fault

Hi from France. I'm the owner of a SAMSUNG W0804Y8E/XEF washer. I tried to run the diagnostic mode as you show in your video but when I push the same buttons as you to enter the mode the result is not the same and I have not the TST mode appearing on the screen. Can you tell me where I can find the specific process for my washer? thanks a lot.

my washer stops on the spin ,can you help please or should i buy one .thank you

@MikeCarter

Жыл бұрын

Mine too. From watching videos and reading around it appears to be caused by the PCB needing replacement. Was it intermittent stopping on spin cycles or every time on any wash programme?

Hi, why my samsung machine takes the fabric softenes at the beginning of the wash and not at the end, my clothes are without good smell because of this???

Running the test mode, my Samsung washing machine don´t run on anti--clockwise rotation and show the Error 3E. Board problem or motor?

Good evening, I have a Samsung WF80F5E0W4W washing machine, sometimes it stops, the display stays on but the remaining minutes of the wash do not go down, generally it stops at 50...53 minutes remaining and it doesn't unlock unless I turn it off and restart it, sometimes it gives me 3E error. I checked the motor brushes and they are good... they will be about 2.5cm long. Do you think it could be a problem with the card? Thank you Roberto

@How-to-repair

16 күн бұрын

Hi Roberto, I've created an FAQ page for you. You can find a detailed repair guide for your problem on this page. Here is the link: www.how-to-repair.com/faqs/samsung-wf80f5e0w4w-washing-machine-stops-gives-3e-error-code/ Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/ 😇 Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

My Samsung WM EcoBubble WF70** have error code 3E. I did a latest test (4) from TEST procedure, where motor spins on both directions. Motor start to spin on first direction just fine, but then when it needs to switch direction of spin - it's stops with 3E code. What could be the problem - Motor or Electronic? I mean - what to look as most possible issue? As motor spins normally in one direction and pass all 3 tests, before test number 4. Thanks!

I dont see a code for AE6. How do you check the connectors...pull every wire connector apart? How can connectors come apart anyway?

Hello. I have a samsung ww90k6410qx eccoblue washing machine (with dash). when doing the test it is NOT possible to enter. I want to check the bucket/drum temperature because it "disarms" my clothes creating a lot of lint, wearing out the clothes and leaving kilos of lint in the dryer. Thank you.

dude you might just save a lot of money. sadly 3C error is back when i diagnostic mode. cant even go into the test mode anymore just getting :- _ icon

Getting error 4c in some programs like baby care ,denim etc and not getting error in quick wash and rinse and spin programs, what it means and how to solve it

Hello sir how can unlocked Al Ecobubbles washing machine (samsung).i appreciated it if you can help me.thanks

on the old model the circulation pump is at the rear and the drainage pump at the front?

@How-to-repair

Жыл бұрын

Thank you For leaving a comment this is for you kzread.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

Hi. I have one of these washing machine that is not working. Don’t need anymore. Do you want to pick it up? I thought I would ask before throw it away.

Hi i have the same washing machine the issue am facing is that the buttons on the dash stopped working ecept the on/off play buttons so i can actually use the washing machine but cant adjust ant of the cycles (spin , water temp..) any pointers would be highly appreciated Note: Child lock is not on :)

Hi. what if the machine won't go on diagnostics and calibration mode? After pressing the buttons sequences, it initiates but stops after just 2-3 seconds. The drum also won't spin anymore on cycle I select. Pls. Help.

@How-to-repair

2 жыл бұрын

Some machines have different test sequences . Thanks please remember to subscribe as that's is was keeps this channel going. Thanks 👍

Hello good sir, great video. I’ve done all the steps and the washing machine appears to be working correctly. However whenever I try and run an actual cycle, it stops after 1 minute, I’m perplexed. Any ideas?

@Este974

Жыл бұрын

Same problem!! Any news about this problem?

@thes9220

9 ай бұрын

I have very similar problem. Machine fills up with water, but after when it come to spin, it stuck. Machine is not under or overloaded. Not heavy things inside. Any thoughts people?

@MKasap-te8vm

8 ай бұрын

​@@thes9220did you resolve the problem? What was the cause of the problem?

Do you know how to enter text mode for ariston dishwasher?

@How-to-repair

2 жыл бұрын

This really depends if the software where has the self-diagnostic mode built into it and this depends on the model I'm glad I could help you please remember to subscribe to the channel as that's what keeps us going and able to make these videos for you

Unfortunately following the sequence and locked my machine, tried all ways that I can imagine but remains in cotton wash mode. the samsung machine in question is a 12kg eco bubble.

I have a Samsung WF45H6300AW/A2 washer. It is having spin issues. I took the back cover off and the rotor is cracked at the hub and has play back and forth. I tightened the 19mm retaining nut and still has play. Am I correct in thinking that is my problem and I need a new rotor?

@How-to-repair

Жыл бұрын

without having the washing machine in front of m a very hard one for me to answer Thank you for leaving a comment this is for you kzread.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

Hai I have problem my machine shows 2 clocks sign n I Kwon haw to remove one lock and the athor one I can't remove it n if I try to spine it Sheck bedle

unable to enter into diagnostic mode for samsung ww80k5210ww Add wash model. I followed the same instructions as shown in your video. Can you help me on this.

@MikeCarter

Жыл бұрын

My Samsung ecobubble ww10n645rpx/eu model doesn’t appear to respond to the suggested button presses to enter diagnostic mode either. Not found a solution - have you @aniserver?

what happens if ive changed Samsung WW80M645OPX pcu b board. thermister checked resistance decreases with hand heat so that works tested element 2.2ohms no voltage reaches element so point back to pcb but that been changed. i dont get error codes just no hot wash iam out of ideas.

My Samsung eco bubble 8 kg runs the woolprogram perfectly while all the other programs have their difficulties. In the test mode the display shows an e3 error. Has anyone a suggestion

Sir I have Samsung Washing machine ww70j5. Its display flashes with only number 8 but it will not turn on. Could you help me with that please?

Hi pal on my eco bubble on some cycles half way through it's shuts down and I have to unplug it from the wall leave it a while plug back in and it restarts ...any ideas cheers pal

@How-to-repair

2 жыл бұрын

have you checked motor ? thanks 👍 for watching and please remember to subscribe to the Channel as that's what keeps us going in able to make the video for you

Hi sir, what if after checking spn mode I received 3E1 error code. What is the problem with that error code. Thank you and hoping to hear from you soon. Robel

During doing the test mode I got problem of 3E, I cleaned the filter as well. What shall I do?

@How-to-repair

2 жыл бұрын

Depending on which motor you have this may be a problem with the hall sensor or the carbon brushes in the motor. Thanks please remember to subscribe as that's is was keeps this channel going. Thanks 👍

I keep getting error 3E on mine. When I do the smart check app it says check motor. Motor brushes have been replaced and still not working. It starts a cycle but keeps stopping mid way through. New circuit board today and that was faulty and wouldn't let us press on and off or move the dial through cycles. And turned on itself when plugged in without pressing the on off button. The washer guy is going to order another circuit board. Do u think that's what the issue is when it states check motor?

@How-to-repair

2 жыл бұрын

It will be PCB or motor fault. Thanks please remember to subscribe as that's is was keeps this channel going. Thanks 👍

6e2 is the error code I can cut it on and have the display lit up like a Christmas tree but I have no control over the dail or buttons

Hello my washer pauses mid cicle without spinning and then pauses itself. Also is not able to do a spin cycle unless is at 400 rpm. If i go into diagnosis mode i get this "-:". Do you have any thoughts?

@helinshevchuk5037

8 ай бұрын

Hi, did you find an issue? I have the same problem

On mine the knob that changes the type off washing cycle stuck on “Normal” it doesn’ change from there to any other moving to left or right, any help?. Thanks in advance.

@How-to-repair

Жыл бұрын

might be faulty pcb Thank you For leaving a comment this is for you kzread.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍