Wouldn't it be easier to just clamp a straight edge to the workpiece and use that as a guide? The method in the video essentially does the same thing, but with the added step of screwing a piece of wood to the jigsaw.

@BStarCrafts

2 жыл бұрын

Thank you for good comments 😊 Have a nice time 🍀

@marcoguo9633

2 жыл бұрын

I think theres a good chance that the jigsaw could wear out the edge or cut straight through in that case. I can see why this method is better long-term since it doesnt wear out the straight edge after repeated uses.

@marcopinchetti5872

2 жыл бұрын

your idea has one benefit: you can cut thicker pieces. THOUGH: it's not so immediate to place the "guide rail" at the perfect distance. It's easy, but not as immediate as this method reaches

@newmonengineering

2 жыл бұрын

@@marcopinchetti5872 the way I do it is by using guide blocks. Basically a pair of blocks that define the distance from the guide to the line. It's fast to set up and you can always use a metal guide like a t track if you are concerned about wear. But if you are doing a lot of them it can become time consuming in comparison to this method

@powerpc6037

2 жыл бұрын

Not to mention the added distance between the machine and the workpiece, allowing the blade to bend a little when it follows the grain of the wood. with the machine on the workpiece itself, the blade cannot bend that far, allowing for more precise cuts.Also, wood against wood gives more friction instead of metal against wood.

역시 응용면에서는 따라갈 사라이 없을듯 유익한 영상 잘보고갑니다 다음 영상도 기대해볼께요 ~~~

@BStarCrafts

2 жыл бұрын

감사합니다~ 이번주 사업 대박 대박 기원합니다 🍀🎁👍

Better to use the right tool for the right job. But if you have nothing else, I guess this can work as a permanent workaround if you not planning use the jigsaw for something else. Can also just use a guide and clamp as usual instead of fixing wood to the jigsaw which you will need to remove again when using it as intended. The ideal tool will be a circular saw and will give a much more desirable finish. Jigsaw is better for odd shapes, curves and tight corners in my opinion.

@BStarCrafts

2 жыл бұрын

Thank you 😊 🍀👌Have a nice time 🍀

@chowderwhillis9448

2 жыл бұрын

Exactly no offense uploaded but this is kinda stupid and just to get KZread views, not practical on the jobsite

@b3arwithm3

Жыл бұрын

Exactly, the blade always flex thus no point trying to make accurate cuts. The only benefit of this jig is we don't have to account for the width of the base when placing the straight egde

@nameless5r

Жыл бұрын

@@chowderwhillis9448 not really but you're entitled to your stupid opinion... So.....

@SimplySketchyXbox

Жыл бұрын

Indeed a track saw will work better. But if you need to use a jigsaw this is a genius method.

형님의 아이디어는 늘 새롭습니다~^^ 너무 멋진 방법이네요~*^^*

@BStarCrafts

2 жыл бұрын

고마워 선화야~ 이번주도 해피 해피 🍀💚 날 풀려서 굿데이네 😁😊🤜🤛

I think this is a nice idea for when cutting close to the edge of a board, where the sole plate might wobble, otherwise a clamped straight edge will do the same when the base is fully supported.

@BStarCrafts

2 жыл бұрын

Thank you 😊👍👍🤜🤛🎵😊 Have a nice time 🍀

@kingpooty2

2 жыл бұрын

@Jesus has given you all. Repent or die. 🤣😂😆

@martinr2962

2 жыл бұрын

In my experience, a straight edge makes the cut not really straight, since the blade tends to wobble if the saw itself can't move freely.

@KodyKimani

Жыл бұрын

Even using a straight edge you won't get a perfect finish with a jigsaw - circular saw better- or this jig looks good !

@tomaspisecky4835

Жыл бұрын

Jfyi this is still straight edge, just against different face, so both will have same result. Yes cheap low quality blades flex and not cutting straight, good blades give good cuts (but they tend to snap as they are usually hardened thus more brittle)

Neat idea! Thought about the same thing a few days ago, as whenever i cut, i have to work out the inconsistencies later, getting tired of it, wasting time.

The black plastic guard that is on the bottom of the jigsaw...actually has square and parallel sides. Put a straight edge on the top of your timber and use it instead. Good brands state on them how wide they are between the edge and jigsaw edge.

@BStarCrafts

11 ай бұрын

Thank you 😊 Have a nice time 🍀

Great idea and demonstration! I’m going to do this to my reciprocating saw.

@BStarCrafts

2 жыл бұрын

Thank you 💚👍😊 Have a nice time 🍀

가이드를 멋지게 만드셨네요. 좋은 아이디어입니다 톱작업 대신으로 작업해도 될것같네요. 지금 리모델링하는 작업대가 완성되면 제작해보겠습니다..감사합니다~~✅

@BStarCrafts

Жыл бұрын

감사합니다~ 추운데 안전 작업하세요~^^

Excellent! Really great way to keep the cut straight. 😎

@BStarCrafts

2 жыл бұрын

Thank you 😊👍💚😊 Have a nice time 🍀

Thank you. This video is precisely what I needed.

@BStarCrafts

2 жыл бұрын

Thank you 💚👍🤜🤛🎵😊 Have a nice time 🍀

If you use templates this works with almost every shape, including guitars. This is actually a very common and straightforward method. But if you want something straight, a chisel or a plane would also do a fine job, just takes more skill and time.

와... 이건 저도 써먹어야겠어요 🌟🌟 매번 잘 보고 가요 😶‍🌫️😶‍🌫️

@BStarCrafts

2 жыл бұрын

감사합니다. 저보다 훨씬 정교하게 잘 만드세요~ 🤜🤛👍💚😊

🙃🥴The irony of this video is that you need advanced power tools, like a table saw, to create a jig for making straight cuts with a jigsaw. However, if beginners had access to those advanced tools, they would likely choose to use them instead of a jigsaw for this specific task.

@liam314

3 ай бұрын

You could use the factory edge of a sheet of plywood to make this. That way you would not have to make any accurate cuts to make this jig. But you make a fair point. This is always the problem with these types of yt videos, "excuse me while I whip out my perfectly set up table saw to make a jig for cutting straight lines!" ;) Anyway, I will try to make this using only a jigsaw and a cordless drill

Сверху пил ровный, а вот за счёт мягкости пилки и фиксации её только с одной стороны 90° торец всё равно не получится. Только Фрезер, ленточная пила или циркулярная даст ровный пил и торец 90°... Бессмысленная приблуда, с тем же успехом можно подошву лобзика просто упирать в направляющую

@BStarCrafts

Жыл бұрын

Спасибо 😊 Хорошего дня 🍀 감사합니다 😊😊 좋은 하루 되세요 🍀

@user-ji7sc5dz9g

Ай бұрын

Б. Инженеры придумали инструмент, для криволинейных распилов. Нет. Б. Народ, упорно продолжает пытаться запустить его прямо.

Ficou muito top seu vídeo parabéns já deixei o meu like 🇧🇷👍👍👍👍👍💯

@BStarCrafts

2 жыл бұрын

Obrigado 😊💚💚🤜🤛😊 Tenha um bom dia 🍀

If you have a square or a straight endge you can run it against the the saw guide and will save you time and gives precision.

@theredrooster7143

Жыл бұрын

Yeah, there’s no point in doing what he did if you’re running the saw against a straight edge anyway. Just back up the straight edge and run the guide along it like you said.

Great idea mate will deffo use it especially if I can find my plastic footplate, I can set it up and use it at will!

@BStarCrafts

8 ай бұрын

Thank you 😊 Have a nice time 🍀

Thank You. I need to make angled cuts on a 1900mm piece of plywood. This will do the job much more accurately than trying to follow a line. In fact I can use it with a circular saw. Much better than the saw guide cutting through the centre that I tried. Straight edge is of course another piece of ply.👍👍👍

@BStarCrafts

10 ай бұрын

Thank you 🤜🤛😊 Have a nice time 🍀

Thanks for sharing your knowledge

@BStarCrafts

2 жыл бұрын

Thank you 💚🎁😊 Have a nice time 🍀

Hey Maker. Great tips. Thanks for sharing.🍁🍁👍👍

@BStarCrafts

2 жыл бұрын

Thank you 💚😊 Have a nice time 🍀

최고 ^^ 안그래도 직쏘기 가이드 만들려고 했는데 마침 이런 동영상이 있었네요. 참고하겠습니다.

@BStarCrafts

2 жыл бұрын

감사합니다. 혹시 탭핑 비트 있으시면 오늘 올린 원형톱 응용 영상을 참고하시면 일직선(영점) 잡기가 훨씬 수월할 겁니다. 좋은 저녁되시고 안전 작업하세요. 🍀🤜🤛😊

@hermannclasen8196

2 жыл бұрын

@@BStarCrafts dä

@sajasaja4930

2 жыл бұрын

T twe

Ficou top das galáxias. 👍

@BStarCrafts

2 жыл бұрын

Obrigado 😊💚💚💚💚😊 Tenha um bom dia 🍀

Buenísimo. Gracias por compartir 👍👍

@BStarCrafts

2 жыл бұрын

Gracias 🎁💚💚💚💚😊 Que tengas un buen día 👍🍀👌

Great solution to finish 👏👍 Even with a circular saw you could get a wobble.

@BStarCrafts

Жыл бұрын

Thank you 😊 Have a nice time 🍀

@CraigLumpyLemke

Жыл бұрын

Circular saws wobble but the saw kerf is consistent. When used with a fence, wobble will produce a kerf wider than the blade, but it won't produce a wandering cut like a saber saw. The angle of the blade to the work does not vary in a circular saw. It varies quite a bit, and unpredictably, in a saber saw.

A clever idea for specific purposes. Neat! Happy building and staying busy. Northern Michigan here by the way. 😁

@BStarCrafts

Жыл бұрын

Thank you 💚👋😊 Have a nice time 🍀

Simple jig but very Accurate and precise thanks for sharing

@BStarCrafts

2 жыл бұрын

Thank you 🤜🤛👍😊 Have a nice time 🍀

페스툴 직쏘기가 따로 필요 없겠네요~~~~ㅋ 정보 감사합니다~~ㅎ 추석명절 잘 보내세요~~^^

@BStarCrafts

Жыл бұрын

페스툴님과 비교해주시다니… ㅎㅎ 명절 잘 보내시고 좋은 밤 되세요 👋💚🍀

С направляющей планкой можно было добиться такого же результата с самого начала.

Bien . Astuce facile et simple 👍

@BStarCrafts

2 жыл бұрын

Merci.💚 passe une bonne journée 😄🍀

Bravo ! Cette astuce est géniale !

@BStarCrafts

2 жыл бұрын

Merci. 🤜🤛🎵👍💚passe une bonne journée 😄🍀

Bravo, belle réalisation, c'est simple, mais il fallait y penser 👍😃. Comme quoi, avec un peu de réflexion, tout est réalisable !

@BStarCrafts

2 жыл бұрын

Merci. 🤜🤛👍💚 passe une bonne journée 😄🍀

The best cut and under the panel👍In Switzerland we put the machine under the panel

@BStarCrafts

2 жыл бұрын

Thank you 👍💚🇨🇭😊 Have a nice time 🍀

Nice job really useful 👍 🙏

@BStarCrafts

2 жыл бұрын

Thank you 😊 💚🤜🤛 Have a nice day 🍀

This is a great idea. Thanks for the video.

@BStarCrafts

2 жыл бұрын

Thank you 🤜🤛💚😊 Have a nice time 🍀

@joeshuge

2 жыл бұрын

It's a complete waste of time, did you see he clamped the straight piece of wood to the wood he was cutting? All he had to do was move it over to allow the blade to cut on the line he wanted to cut and just keep the base of the jigsaw tight to the clamped wood, he would have had the exact same outcome without going through all the wasted time attaching a piece of wood to his jigsaw.

El sabe sabe, abrazo desde argentina. Gracias por compartir su sabiduría.

@BStarCrafts

Жыл бұрын

Gracias 😊 Que tengas un buen día 👍🍀👌

Probably wouldn’t be using a jigsaw if I needed straight cuts but making jigs are enjoyable. Good job on that.

@BStarCrafts

Жыл бұрын

Thank you 😊 Have a nice time 🍀

I could swear when I used to do a bit of cutting that a gremlin was in the saw and on purpose always pushed it off line, cheers for this

@BStarCrafts

Жыл бұрын

Thank you 🤜🤛😊 Have a nice time 🍀

Amazing, I never realised you could get screw driver bits with handles on. LOL.

@BStarCrafts

5 ай бұрын

Thank you 😊 Have a nice time 🍀

Try to take a saw for aluminum, it is more rigid and cuts, so the cut is smooth!

Nice work. Kind of like a handheld jointer. You could just also make the initial cut with a router and a panel trimming bit.

@BStarCrafts

2 жыл бұрын

👌👍 Thank you 💚🤜🤛😊 Have a nice time 🍀

굿 아이디어 입니다

@BStarCrafts

2 жыл бұрын

감사합니다 😊👍💚😊 좋은 하루 되세요 🍀

Thanks for sharing 👍

@BStarCrafts

2 жыл бұрын

Thank you bro 💚😊 Have a nice time 🍀

와 기발하다.. 좋은정보 감사합니다. 내일 당장 만들어봐야겠어요!

@BStarCrafts

2 жыл бұрын

감사합니다. 이번에 새로이 업로드한 원형톱 응용 영상을 보시면 조금 더 참고가 되시듯 합니다 💚👍😊🎁🍀

Thank you/from Thailand.

@BStarCrafts

2 жыл бұрын

ขอบคุณค่ะ 😊💚🎁 ขอให้เป็นวันที่ดีนะคะ 🍀🇹🇭

안녕하세요 구독 좋아요 꾹꾹 누르고 시청하고 있습니다 저도 만드는걸 좋아해서 여러가지 국가 기능자격증도 취득하고 더 좋은 제품을 만들고 싶어서 도전 중입니다 선생님께서 알려주신 방법은 제게 가구 제작 기능사 실기 시험을 보는데 많은 도움을 줄걸로 사로 됩니다 아울러 선생님 채널도 번창하세요

@BStarCrafts

2 жыл бұрын

감사합니다~ 하시는 일 대박 나시고 시험도 한번에 붙으시길 바라겠습니다 🍀🍀💚🎵👍

Terimakasih banyak atas idenya.. Two tump up... Bogor Indonesia hadir

@BStarCrafts

2 жыл бұрын

Terima kasih 💚🇮🇩😊 Semoga harimu menyenangkan 👍🍀👌

Parabéns pela excelente ideia. Pergunta: por que as legendas em português?

@BStarCrafts

2 жыл бұрын

Obrigado 😊😊 Tenha um bom dia 🍀 Traduza e carregue vários idiomas. 🎁

Excelente proyecto muy bien desarrollado y mejor ejecutado , con esa plantilla fácil de hacer y de colocar , problema resuelto y buenos cortés , gracias por compartir tanta creatividad y conocimientos , un saludo cordial y por supuesto un gran like desde Narón , Galicia (España) 🤓 🛠️ 🔝

@BStarCrafts

2 жыл бұрын

🙆🙆🙆 Gracias Viorsa 🍀🎁👍🤜🤛😊 Que tengas un buen día 👍🍀👌

Dziękuję bardzo 😉

@BStarCrafts

2 жыл бұрын

dziękuję 😊 miłego dnia 💚👍

@piotrpawelec2008

2 жыл бұрын

@@BStarCrafts 🙂😉

Crap! It seems that I need to buy a table saw in order to make a jury rigging of my jigsaw in order to not having to buy a table say... 🤣

Very good idea but I always have blade deflection when I use a jigsaw. Never cuts square for me and I`ve tried many high quality blades. I think you would have the same problem with this technique cutting curvy lines thru thicker stock.

@BStarCrafts

11 ай бұрын

Thank you 😊 Have a nice time 🍀

So all I need is a table saw to make a tool to do what a table saw can do.

Perfeito, obrigado por compartilhar.

@BStarCrafts

2 жыл бұрын

Obrigado 😊👍👍👍😊 Tenha um bom dia 🍀

@carlospereira1293

2 жыл бұрын

Gostei! Tipo a SP6000 makita. Com guia.

thank you for this video!

@BStarCrafts

2 жыл бұрын

Thank you 😊 🤜🤛 👍 Have a nice day 🍀

Very clever, thanks for the upload.

@BStarCrafts

2 жыл бұрын

Thank you 🎵👍💚😊 Have a nice time 🍀

Complimenti👍 Ottima tecnica👍

@BStarCrafts

2 жыл бұрын

Grazie. 😄👍 Buona giornata 🍀🍀🍀🍀

can't see how this is better than running the jigsaw down the guide rail you attached with the clamps and not messing around with a bit of wood screwed to the jigsaw

@BStarCrafts

2 жыл бұрын

Thank you 😊 Have a nice time 🍀

Super! Ich liebe solche simple und hilfreiche ideen 👌🏽

@BStarCrafts

Жыл бұрын

Danke 🤜🤛💚🥹😊 Schönen Tag 🍀

Just clamp a straight edge to your workand use it as a guide. Works great for jig saws and circular saws.

@BStarCrafts

2 жыл бұрын

Thank you 😊 Have a nice time 🍀

Brilliant idea! (and great for tight spaces..🍺

@BStarCrafts

2 жыл бұрын

🤜🤛🎵🍀💚Thank you 😊 Have a nice time 🍀

Ingenious idea 👍👍👍

@BStarCrafts

2 жыл бұрын

Thank you 🤜🤛👍💚😊 Have a nice time 🍀

Nice idea... Never thought before... Thanks

@BStarCrafts

2 жыл бұрын

Thank you 🎵💚🤜🤛😊 Have a nice time 🍀

Ill I can say is…AMAZING!!! Im gonna make one!

@BStarCrafts

2 жыл бұрын

Thank you 💚🎁👍😊 Have a nice time 🍀

와우 감사합니다. 자처럼대고자르는 나무두께와 직소바닦에있는 나무두께가 동일해야겠네요. 안그러면 약간사선으로잘릴듯하네요. 그런궁금증이생기네요^^ 아닌가? ㅋㅋ 잘몰라서요... 정말고민많이했는데, 이렇게 알려주시니 감사드립니다.^^

@BStarCrafts

2 жыл бұрын

네 아주 정확하게 보셨어요. 사실 영상을 찍을 땐 귀찮아서 12T를 대고 잘랐는데 안정적으로 자르기 위해선 지그 두께와 같은 18T를 대고 자르면 아주 좋습니다. 그래서 그 다음 영상인 원형톱은 18T로… 😅 좋은 하루되세요.👍💚🍀🎁🤜🤛

@papabeoms

2 жыл бұрын

@@BStarCrafts 정말 좋은 아이디어 제공해주셔서 감사드립니다.^^ 영상 자주보고 있어요~ 즐겁게 취미생활할수 있게 도움많이 주셔서 감사해요~

Using a jigsaw which tons of people have... and a router which most people don't even know exists😅

I love the bit where you need a table saw to get the straight cut on the guide you need for a tool thats not the best option, still have to clamp straight edge to your work, and will still probably get a wonky edge because it's a jig saw. 😂 Either cut with a jig saw and use the router to get the edge you want, or cut with the damn table saw

@BStarCrafts

2 ай бұрын

Thank you 😊 Have a nice time 🍀

간단하면서 실용적이네요👏😁😊 역시 아이디어뱅크!👍 요새 매일 공방에 계시나요 언제 연락 드리고 갈께요~

@BStarCrafts

2 жыл бұрын

감사 감사합니다 😁😁😁 네 오셔서 차 한잔 하고 가세요. 요즘은 자주 나가진 않습니다만 닐 풀리면 자주 나갈라고요. 👌😊

Genial! Ficou ótimo

@BStarCrafts

Жыл бұрын

Obrigado 😊💚😊 Tenha um bom dia 🍀

Que maravilha! Gratidão 😃👏👏👏🤗.

@BStarCrafts

Жыл бұрын

Obrigado 😊🤜🤛😊 Tenha um bom dia 🍀

Всё гениальное - просто! 🤝👍

@BStarCrafts

Жыл бұрын

Спасибо 😊 Хорошего дня 🍀

This is an excellent idea, thanks

@BStarCrafts

2 жыл бұрын

Thank you 👍🎁🤜🤛💚😊 Have a nice time 🍀

You will never have the same quality of edge as with a flush trim bit! The jigsaw blade has too much deflection(flex) in it....better to use a table saw or circular saw!

@stigmautomata

8 ай бұрын

i like this design as it allows the clamped guide to be placed directly on the intended cut,

@sampathkumar3018

7 ай бұрын

Yes. I too found it difficult inspite of all adjustments.

@Musicpins

4 ай бұрын

Because most jigsaws is junk, a circ saw is better yes.

@GustavoArayaPaillas

2 ай бұрын

😊😊😊😊😊😊😊

Circular saw and homemade guide.

Great video! Thank you.

@BStarCrafts

Жыл бұрын

Thank you 😊 Have a nice time 🍀

I like that. Greetings from Germany. Amithaba.

@BStarCrafts

2 жыл бұрын

Danke 😊 🇩🇪 Schönen Tag 🍀 Thank you 😊 Have a nice time 🍀

Молодец,возьму на заметку(пример)

This is brilliant. Thank you.

@BStarCrafts

4 ай бұрын

Thank you 😊 Have a nice time 🍀

Muy buena opcion cuando no tenemos sierra de cinta. Gracias!!

@BStarCrafts

2 жыл бұрын

Gracias 😊 Que tengas un buen día 👍🍀👌

@TvJRB

2 жыл бұрын

@@BStarCrafts Muchas gracias!!

Could you use this for a circular saw? I hate measuring over from the blade to the edge of the foot to clamp a straight edge.

@BStarCrafts

Жыл бұрын

Oh~ There is a video I made using a circle saw after that video!! Thank you 😊 Have a nice time 🍀

Very good my friend 👏🏽

@BStarCrafts

2 жыл бұрын

Thank you my friend 💚🎵😊 Have a nice time 🍀

showwwww melhor de todos que vi ♥ amei ♥

@BStarCrafts

2 жыл бұрын

Obrigado 😊🤜🤛👍🎵😊 Tenha um bom dia 🍀

That is a really good idea. Cheers

@BStarCrafts

Жыл бұрын

Thank you 🤜🤛🙏💚😊 Have a nice time 🍀

Um trabalho profissional

@BStarCrafts

2 жыл бұрын

Obrigado 😊💚🎁👍😊 Tenha um bom dia 🍀

Congratulations!!!🙏🙏🙏

@BStarCrafts

2 жыл бұрын

Thank you 🎁💚👍😊 Have a nice time 🍀

Также сделаю. Спасибо автору за идею.

@BStarCrafts

Жыл бұрын

Спасибо 😊 Хорошего дня 🍀

Mantap Pak Eko.... Terimakasih 🙏🙏🙏

@BStarCrafts

Жыл бұрын

terima kasih. 😍💚👍 Semoga hari anda indah. 🍀😄🇲🇾

Good solution to a jigsaw puzzle 👏

@BStarCrafts

Жыл бұрын

Thank you 😊 Have a nice time 🍀

👌🙏

@BStarCrafts

8 ай бұрын

🍀😊💚

Хорошо ,ты молодец!

@BStarCrafts

2 жыл бұрын

Спасибо 🤜🤛👍🎁😊 Хорошего дня 🍀

👏👏👏like e Seguindo!!!

@BStarCrafts

2 жыл бұрын

Obrigado 😊💚😊 Tenha um bom dia 🍀

안녕하세요 영상 맨처음에 나오는 구불구불한 형태처럼, 드로잉같은 자유분방한 형태로 자르는 작업을 하고자 합니다. 영상에 나오는 형태도 직쏘로 자르신 것인가요? 또 자르신 나무는 어떤 집성목인지 여쭤봐도 될까요?

@BStarCrafts

Ай бұрын

네 같은 직소기로 자른 거 맞습니다. 원래 직소기는 구불구불 자르는데 특화되어 있습니다. 영상 사용한 목재는 고무 나무입니다. 주말 잘 보내세요 🍀

@miryu_kim

Ай бұрын

@@BStarCrafts 와 답변해주셔서 정말 감사합니다!!

Interesting, I wonder if you left the hole round, and fitted a Delrin plug with a slot the same width as the blade would make it cut even truer.

@BStarCrafts

Жыл бұрын

Thank you 😊

That’s good I don’t have a router if can remember how to do it would be great thanks Tony

@BStarCrafts

2 жыл бұрын

Thank you Mr.Tony 💚👍🎵🎁😊 Have a nice time 🍀

*TOP IDEA* 😍

@BStarCrafts

2 жыл бұрын

Thank you 😊 Have a nice time 🍀 Terima kasih 😊 Semoga harimu menyenangkan 👍🍀👌

I tried to do something like this the other day, but I found that my jigsaw blade bent over sideways and went whereever it wanted anyway. Even if you get it straight horizontally, it’s not very square in the vertical direction.

@BStarCrafts

7 ай бұрын

Thank you for advice 😊 Have a nice time 🍀

Bravo, très astucieux.

@BStarCrafts

2 жыл бұрын

Merci. 👍💚passe une bonne journée 😄🍀

It still wandered! That’s the nature of the jig saw beast! Nice try however.

@BStarCrafts

7 ай бұрын

Thank you 😊 👍Have a nice time 🍀

🥰🥰🥰, thanks for sharing!

@BStarCrafts

Жыл бұрын

Thank you 🤜🤛👍💚😊 Have a nice time 🍀

Nice ideas broo..👍👍👍

@BStarCrafts

2 жыл бұрын

Thank you bro…! 👍💚😊 Have a nice day 🍀