spindle rpm 11000 and feed rate 600mm doc is 1mm machine is home made mdf 0.75kw spindle
Жүктеу.....
Пікірлер: 199
@HomeCockpitSolutions5 жыл бұрын
cutting informations added
@yougiovesjotube
2 жыл бұрын
How you get that?
@Michael-lo3ht5 жыл бұрын
Great job. Exactly what I want to use mine for. FYI, you can use double sticky tape to hold it in place for when it cuts the item free. Less dangerous.
@theonegaming71565 жыл бұрын
Amazing cut ! , can you please share the bit specifications
@kristofepic9 жыл бұрын
nice job, can you give a link to the milling bit?
@stacytjoa41539 жыл бұрын
Looks like a solid machine. I saw that you had to use your finger to press down on the workpiece as it was becoming detached from the frame, not sure if you were just going in for a quick test but in future you could double side tape the workpiece to the bottom.
@JKTCreation
8 жыл бұрын
+Stacy Tjoa good observation :)
@kanchour165 жыл бұрын
Nice job but you should share with us how did you build your cnc it looks 👀 powerful great job
@maxngc4 ай бұрын
I LOVE THE SAUND OF THE STEPPER MOTORS!
@leduj10 жыл бұрын
Thanks for sharing the videos
@phucnguyenCNC7 жыл бұрын
Verry nice!
@charlesmarlin66326 жыл бұрын
Do you remember what your feeds/speeds was on the holes and profile cuts? :-) Nice Cuts :-) Thank You for the video.
@videosallnight4 жыл бұрын
The trick is to use a vacuum cleaner to suck up the debris. I took a flexible hose, and set up a clamp to hold it close to the end mill. I even made a small shroud that surrounds the tool gets debris even from all around.
@Bluntedco.4 жыл бұрын
can you die cut something like this with a plunge router or table top router or trim router which do you suggest? i am new to this and harbor freights offers those items. i pretty much have a 14x16 piece of plexi that i need to die cut some ovals thank you for your time!
@amitkumar67846 ай бұрын
Nice and smooth 😊
@HadaZero10 жыл бұрын
Hi, could you please advise what king of end mill are you using to cut and where could I find it ? THANK YOU
@MCircuits4 жыл бұрын
I think The user here was using the Single flute end mill..That was the best on cutting Cast And Extruded Acrylic.
@longxingacrylic169110 жыл бұрын
perfect
@BullBosphorus7 жыл бұрын
Merhaba Atakan, hocam kesim baya guzel. Hangi ucakta kullaniliyor?
@HomeCockpitSolutions
7 жыл бұрын
bu kesilen parca 737 nin flap gostergesi cami icindi ama cok eski bir calisma ve tasarim. suan yenisini yaptim yakin zamanda videosunu atarim
@BullBosphorus
7 жыл бұрын
GuZel merak ettim. Bekliyorum videoyu
@anaknaabahkholid6 жыл бұрын
So good mechine cutting
@tommasodarpa10812 жыл бұрын
which tip did you use for the cut?
@snugglylovemuffin8 жыл бұрын
It almost looks like you should take smaller passes at a higher speed, did you find that to be the case? Just heard some chattering on the first pass.
@lophole78 жыл бұрын
I use Onsrud 1 flute bits and don't get edge finish like you have. My cut edge is not clear like that . Please what the name of the bit and where you got it and what size. I'm using .25" Onsrud #63-622
@PAPENG_GAMING5 жыл бұрын
what kind of cutter that you use for cutting the acrylic sir?
@curtisnewton8953 жыл бұрын
what drill bit do you use?
@user-ug9ev1le2d5 жыл бұрын
О боже как же я хочу, фрезерный станок. Но я не хочу брать кредит.
@alanc949210 жыл бұрын
Ok, now I'm curious..... What is the part for?
@chidubemuzoma4108 жыл бұрын
I will love to have those machines am a sign practitioner, thank you
@pisaubawang6 жыл бұрын
Great
@arturreef81172 жыл бұрын
Where did you bought this, or parts how to build
@martasofia60622 жыл бұрын
Does it matter what type of acrylic its used?
@andershipuuden9 жыл бұрын
SHOW!!!!
@eliasmora7154 жыл бұрын
nice.... i just to have a 30x40 i miss it.
@lana63352 жыл бұрын
Awesome idea1
@calas888 жыл бұрын
Ohhh I get it, The video is 4xF>>
@omarsaleh46610 жыл бұрын
شكرا
@dinakarsa61489 жыл бұрын
till what size we can use
@johnnywebb86967 жыл бұрын
I'd like ta take my SNES apart and 3-D print its case transparent :D
@jamesking4253 жыл бұрын
Hey I was wondering could I get you to do a little project for out of acrylic
@franjalen10 жыл бұрын
NICE, BEAUTIFUL AND CLEAN WORK , THANKS FOR SHARING IT. QUESTIONS ; WHAT KIND OF MACHINE AND PROGRAM YOU ARE USING , WHY TOO MANY CUTS ON IT ?
@zusurs
9 жыл бұрын
I presume so much cuts are done to minimize heat-stress on material, as well as this small milling head isn't durable enough to drill whole thickness of material at once.
@franjalen
9 жыл бұрын
Artūrs Savickis Thanks for your answer .....but I'm not agree with you.....there are too many questions in the air , but the video and the work it looks interesting . Greetings.
@LordAnubis09099 жыл бұрын
what is the speed you are using for tool and moving? i'm having problems with melting :/
@FoivouDady
4 жыл бұрын
Melting is a big problem. To solve , im using 0,4mm per pass, fast feed to prevent melting and MDF bit single flute. Compresed air on cutting point helps also.
@1slippy
3 жыл бұрын
I was going to say he probably gets away with it by making several passes. Do you have a veritable speed control on the motor or is it just one speed? If you can lower the RPM and increase the table feed you could make less passes. It looks like the boy is a .062 dia if you could lower the feed use a .093.
@LordAnubis0909
3 жыл бұрын
I will give it a try. I can change speed on the tool. Just .made new mini cnc to test
@himhirit4 жыл бұрын
Merhaba; Böyle bir makineyle 3mm pleksi kesimi yapılabilinir mi? Kaçlık nasıl bir uç kullanmak gerekir?
@BALBANCI10 жыл бұрын
bu cihazin adi nedir? birde kesilen yerler puruzlu kaliyor mu acba?
@AlexanderLonberg8 жыл бұрын
У меня стекло плавится ... I have the glass melts ...
@irwanlau22246 жыл бұрын
Mantaaaab 👍
@same88253 жыл бұрын
Felt like I was at the dentist for a second. PTSD
@durgeshvarma92676 жыл бұрын
Mere pass acrylic ki sit hai bahot Sari kya price
@appoandi1395 Жыл бұрын
End mill?
@lophole77 жыл бұрын
what's the manufacture of the bit and what size diameter is it. and what's the model number of the bit
@jimealase2848
7 жыл бұрын
Great
@jimealase2848
7 жыл бұрын
good for all
@manwar512
6 жыл бұрын
lophole7
@morosuh10 жыл бұрын
good job ^^
@peeqwear7 жыл бұрын
Eline sağlık. bende bir cnc yaptım ama plexy eriyip uca yapışıyor bunu onune nasil gecerim? uç tek fülüt cnc ucu olmasına ragmen.
Can any one please help with the software and instruction how to use the laser on the 2418. It was supposed to be with the machine or on the disc supplied but there is no instruction. I have learnt how to use the engraver by trial and error. If you know how to locate the instruction on the disc for the laser could you point me in that direction. If not can you please assist with an explanation on how to use the laser and what other free software maybe available for the laser. The pictorials and you tube information is either in Chinese or Russian. Mmmmmmmmmmmmmmmm. Bit of a problem for me. Simple explanations please as I am just a simple Non University Aussie. David.
@dinakarsa61489 жыл бұрын
how much does this machine cost
@DavidBixler9 жыл бұрын
I need this thing
@chidubemuzoma4108 жыл бұрын
I need to know the prices
@JesusHuertamusicshow11 ай бұрын
Me puede indicar cómo se llama esa máquina?
@peliculasclasicasydecultox77995 жыл бұрын
Como que se tardo mucho para hacer ese corte
@iloveyoupapa26166 жыл бұрын
Ser lesar engraving acrylic kat leta hai
@tripives18587 жыл бұрын
Acrylic typically melts when being drilled with a conventional drill bit. Why doesn't it melt when using a spindle bit, especially without coolant? I would think it would. Thanks!
@THOMASTHESAILOR
6 жыл бұрын
If you watch the first few seconds of the video, before he starts the spindle, you can see, he is using a "Roughing" endmill, or some call it a "Corncob" endmill. It has bumps on it, that reduces the area of contact between the cutter and material, therefore, reduces friction/Heat. also, rpms have a lot to do with it. It's all about friction.. My cnc router won't go that slow..
@soyebravat89035 жыл бұрын
Wow awesome machine. Could you advise where you got your bit from
@HomeCockpitSolutions
5 жыл бұрын
i am living in Turkey. from local store
@soyebravat8903
5 жыл бұрын
@@HomeCockpitSolutions hey thanks. I would luv to try and cut acrylic. I make signs and have so many board's just laying here and off cuts. Might as well try and cut something. Do u have the details of the bit or can u advise the name of the shop or if they online?
@HomeCockpitSolutions
5 жыл бұрын
they dont have online shop. you have to but single flute cutter. you can choice diameter what you want. this cutter is single flute 2.5mm diameter and 10mm cutting lenght.
@anlpereira8 жыл бұрын
Hi, great video. I would like to know what is the XY advance speed, what is the Z axis step down and what is the spindle rpm? Thank you very much.
@HomeCockpitSolutions
8 жыл бұрын
+Anderson Lima xy 600mm z is 100mm
@ronniepaulinc
8 жыл бұрын
in 1/4 inch you should make a shallow roughing passing with 2 follow up depth passes and a finish path.. Speed is dificult to say with each cnc, you want to pass as fast as you can but vary your spindle speed to ensure your are not creating enough heat to melt
@ChanDoan10 жыл бұрын
nice setup. Do you have you instructions on how to build this? I'm looking on most of the sites and many are broken links and missing how to's and stuff..
@longxingacrylic1691
10 жыл бұрын
We are acrylic manufactory from China,my skype is king203344 Email:longxingacrylic@163.com
@zusurs
9 жыл бұрын
Belive me - if you have no expirience in building CNC machines (and your question points out you don't), buying cheap-ass (we are still talking for about ~1600$ for 30 by 30 cm (square foot) of working area) small CNC from China will be LOT cheaper and less time consuming than build your own.
@seanpain4
9 жыл бұрын
Artūrs Savickis It may be easier but not way is it less expensive
@zusurs
9 жыл бұрын
Sean Pain It is. If you account all parts, electronics, tools (programming kits and microcontrollers necessary), software and all other hardware, not even mentioning time necesary to learn and build everything, as well as multiple failed attempts at first, buying ready-to-use unit IS cheaper.
@HomeCockpitSolutions
9 жыл бұрын
Artūrs Savickis absolutely true..
@michael12nonan8 жыл бұрын
could i use a dremel tool for this one? what bit should i use?
@HomeCockpitSolutions
8 жыл бұрын
yes you can use dremel but i have to choose dremel with variable speed. you have to choose single flute end mill for pleskiglass, acrylic
@aravindeswar1074 жыл бұрын
Tool bit link please??
@ChrisbottrellphotographyCoUk7 жыл бұрын
we cut acrylic up to 10mm thick single pass, your chip load is Far to low. go faster 4000mm/m
@HomeCockpitSolutions
6 жыл бұрын
Chris Bottrell Photography you are so smart :D but this is mdf amateur cnc ;)
@hyperhektor7733
5 жыл бұрын
lol sure, but did you already tried to max out the machine? even when its a hobby machine it doesnt mean you can try to go faster.
@nicolezhang2340
5 жыл бұрын
pls add my whatsup/wechat: 008613075365628
@Katrinah197010 жыл бұрын
Can u build me one
@prayitnoashuri89596 жыл бұрын
i need to see the result, clean cut or not.
@nicolezhang2340
5 жыл бұрын
you wnat clean cut? my whatsup/wehcat: 008613075365628
@neon_led4you Жыл бұрын
Sa kardeşim 6mm hangi takım ucu tavsiye edersin birde Spindel ayarını ögrenebilimiyim pleksiyi eritmemesi için
@HomeCockpitSolutions
Жыл бұрын
selam. 6mm çap olacaksa plekside mutlaka tek ağızlı bıçak kullanman gerek. kullandığın kesici ucun çapına göre ilerleme hızı ve spindle devri ayarlaman lazım. mesela 800mm/dk ilerleme ile 10 bin devir spindle ile rahat kesmesi lazım 3mm çapında uç ile. tabi çap değişince bunlar da değişir. keserkenki gelen sesi de iyi anlaman lazım makinenin rahat kestiğini anlamalısın
@neon_led4you
Жыл бұрын
@@HomeCockpitSolutions hocam benim yapmak istediğim 5mm pleksi üzerine 2.5m harf kazıma yani komple kesim değil çift üçlü bıçak kullanıyorum bu türlü ayar tutturamadım sürekli pleksiyi eritiyor
@HomeCockpitSolutions
Жыл бұрын
@@neon_led4you o zaman spindle devri çok yüksek deviri düşürün
Atakan bey merhaba corsair 465x beyaz kasamın temperli camını kırdım ve yenisini bulamıyorum ölçü versem ve resim atsam sizin bana 4mm kalınlığında temperli şekilde yapıp gönderme durumunuz olabilir mi?
@HomeCockpitSolutions
3 жыл бұрын
Maalesef
@nicstroud8 жыл бұрын
I have tinnitus now. A different audio track and a slightly higher camera angle would make this video better. Not hating, just saying.
@lass-inangeles7564
8 жыл бұрын
+Nic Stroud Ha, ha, ha! Me too! My ears are buzzing. Some truth to using hearing protection, eh?
@avfbvdfbv7 жыл бұрын
i working with acryling. and is not good seting and very slowly. i use 3.17mm - 1150 mm/min and depth 1.5mm , ot 12 000. better that this . i am sure
@danieltoosi54152 жыл бұрын
If you use tap option, no need use finger
@hussainali8909 Жыл бұрын
Which Software your using?
@hussainali8909
Жыл бұрын
If, can you share how to setting CNC machine with software
@rbtx9910 жыл бұрын
You are cutting it wrong direction. You get better finish when the flute hits the material as you move forward. In you case you'd get the better finish on the outside part.
@3dNaambord3 жыл бұрын
slm Atakan bey kulandiniz frezze ucu ne marka?
@HomeCockpitSolutions
3 жыл бұрын
inanin markasini hatirlamiyorum.
@THOMASTHESAILOR7 жыл бұрын
that's nice, "4X faster" that what,?
@dannyspencer933
6 жыл бұрын
the video was speeded up by 4x rather then watching it cut for 30 mins
@DIYTech217 жыл бұрын
At last the item melted and bit was broken plus the spindle caught fire. He failed in making WHATEVER he was making at WHATEVER machine settings
@HomeCockpitSolutions
7 жыл бұрын
your machine your problem. i wrote my settings. you can look down
@tomjdesigns1280
7 жыл бұрын
Where have you? Can't find any setting
@DavidBixler8 жыл бұрын
What machine is he using? I'm looking to invest for fabricating grills for PCs.
@HomeCockpitSolutions
8 жыл бұрын
Cnc
@DavidBixler
8 жыл бұрын
Duh. What make/model?
@HomeCockpitSolutions
8 жыл бұрын
+David Bixler i made it
@DavidBixler
8 жыл бұрын
You made that machine? Christ how?
@HomeCockpitSolutions
8 жыл бұрын
+David Bixler google it. you can find any information
@tushargajbhiye64874 жыл бұрын
Hello sir, Which tool do you use for acralic no. Cutting?
Merhaba bende bir cnc yaptım 300w spindle motor siparişi verdim gücü nasıl acaba bi fikir verirmisiniz sizin kullandığınız motor kaç w birde
@HomeCockpitSolutions
6 жыл бұрын
Doğru İletişim benim bu videodaki spindle 750w ama simdi buyuk makinemde 2.2kw spindle kullaniyorum. Dusuk devirlerde elinizle durdurmaniz mumkun degil. O yuzden demir ve aluminyum islemek icin yuksek torklu spindle kullanmak gerekir ama plastik ve ufak capli isler yapilacaksa 300 de yeter 750 w da yeter
@dogruiletisim
6 жыл бұрын
Atakan Şenyurt çok sagol peki bu yaptığın işi 300w yApabilirmi
@HomeCockpitSolutions
6 жыл бұрын
Yapar
@StevenKiberton10 жыл бұрын
what bit did you use?? and what speed?
@andreeca
10 жыл бұрын
I'm searching for the same answer :D the speed... P.S. Steven, the bit is single flute end mill, specially for acrylic.
@StevenKiberton
10 жыл бұрын
andreeca Many thanks It looks like the video is speeded up also I have just bought a C02 laser CNC so I will do most of my cutting on that but the working area is only 300x300mm where as my CNC Mill is 1000x1000mm so I will invest in a few of those single flute end mill bits and see what I can get
@HomeCockpitSolutions
10 жыл бұрын
Steven Kiberton this is single flute end mill for acrylic. video 4x faster. spindle rpm 11000 and feed rate 600mm
@StevenKiberton
10 жыл бұрын
Nice work and thank you :)
@Jason-tf4jv6 жыл бұрын
is it extruded acrylic or cast acrylic?
@SisiCheng-nz1jg
3 ай бұрын
Do u need thin acrylic sheet
@MildlyCurious9 жыл бұрын
Why is it not melting to the bit!?
@henk6172
9 жыл бұрын
Because plexiglass is a really soft material, moving to fast would melt the plexiglass, not the bit.
@naticristellavi8236
8 жыл бұрын
+Harm Prins Exactly, that is what happen to me the acrylic or plexiglass melts and adhere to the bit. Is a special bit for doing this? How can I prevent the melted acrylic from adhere to the bit? Thanks
@henk6172
8 жыл бұрын
Naticris Tellavi there are no special bits to cut acrilyc. you just have to keep it from melting. to produce the least heat, your bit has to be sharp, and most important, you don't want to go too fast. the faster you go, the more heat you produce. there are some great feed and speed recipes on the internet.
@naticristellavi8236
8 жыл бұрын
+Harm Prins Thank you. I went to Dremel.com and read the description on the Tugnsten (don't know the spelling) and those bits are made to last longer and designed to produce less heat.
@alexmarion8171
8 жыл бұрын
+MrStankoman because he is using cast acrylic sheet
@yellowpo85903 жыл бұрын
posisi kamera salah cuk, kagak kelihatan...
@djarieljpp7 жыл бұрын
can you please to shared the plans
@HomeCockpitSolutions
7 жыл бұрын
which plans ?
@maheshdesai72717 жыл бұрын
hello all, i want to cut ABS & PP material by using robot. the thickness is near about 6 mm. please suggest me the motor speed type of cutting machine and approximately what should i have to put the speed of robot.
@kendrickxy1774
7 жыл бұрын
I think it should not be a problem cutting it. But maybe if you have an heat gun you should follow the drill with that heat gun (It should be easier to cut). But beware of the bad smell, because it's 100% chemical
@mikeleahy5736 жыл бұрын
A sealed-CO2 laser would cut and polish in a single pass.
@drrmagneto41769 жыл бұрын
where is the best place to buy acrylic
@TylerHarney
9 жыл бұрын
Drr magneto Mcmaster-Carr is where I get mine.
@erictripvlogtv59425 жыл бұрын
what the name of the drill bit you've using?
@samimeka3574 Жыл бұрын
What is the machine name?
@HomeCockpitSolutions
Жыл бұрын
diy mdf cnc machine
@ipadize10 жыл бұрын
you dont need to grind the material :)
@nicolezhang2340
5 жыл бұрын
Yes, our Ld-6000 is suitable for cutting acrylic. my whatsup/wechat: 008613075365628
@angeloramos2007 Жыл бұрын
Thickness 6mm??
@HomeCockpitSolutions
Жыл бұрын
5mm
@jimmytran54766 жыл бұрын
how much is it cost,i need to get one
@HomeCockpitSolutions
6 жыл бұрын
for what ??
@abertkong4321
6 жыл бұрын
hi dear, we also can offer this machine, please contact me wahtsapp+8617153941009
@brian13267 жыл бұрын
faster? what was it before? That is dead slow, what is the chip load 0.005? Can't get any tool life without a good chip load.
@HomeCockpitSolutions
7 жыл бұрын
yes x4 faster. video edited to x4 faster from actual speed. if you look below comment you can see some information ok ?
@lelandwong27717 жыл бұрын
silly brush just pushes the shavings elsewhere; get a vacuum system
@tugaminhoto49697 жыл бұрын
Hi, can You tell what configuration are You using, as: 1) tool diameter and nº of flute. 2) rpm 3) feed rate 4) deep of cut Thanks
@HomeCockpitSolutions
7 жыл бұрын
2mm one flute 12.000rpm 600mm/min feed and 1mm deep of cut
@francispp81
7 жыл бұрын
Eduardo Braga estou apanhando para cortar um acrílico de 5mm aqui rss
@billmorris27558 жыл бұрын
why not just have a fan blowing on it
@lostallmymirth
8 жыл бұрын
+Bill Morris With the use of a shop vac, removal as well as disposal of all plastic swarf will be performed in one operation.
@tomrielly12535 жыл бұрын
you did this in way too many passes.. I would have used a feed rate of around 3000mm/m with a plunge rate of half that, at that rate you could definitely do it in one pass but would do 2 just to be sure of a clean finish.
@dennisfalan16233 жыл бұрын
That was a home made CNC ??????????????????????????????????????????????????????
@HomeCockpitSolutions
3 жыл бұрын
Yes
@M6MDR5 жыл бұрын
Thumbs down due to lack of any information. Showcase videos are only useful if you share information about what you're doing and how you're doing it.
Пікірлер: 199
cutting informations added
@yougiovesjotube
2 жыл бұрын
How you get that?
Great job. Exactly what I want to use mine for. FYI, you can use double sticky tape to hold it in place for when it cuts the item free. Less dangerous.
Amazing cut ! , can you please share the bit specifications
nice job, can you give a link to the milling bit?
Looks like a solid machine. I saw that you had to use your finger to press down on the workpiece as it was becoming detached from the frame, not sure if you were just going in for a quick test but in future you could double side tape the workpiece to the bottom.
@JKTCreation
8 жыл бұрын
+Stacy Tjoa good observation :)
Nice job but you should share with us how did you build your cnc it looks 👀 powerful great job
I LOVE THE SAUND OF THE STEPPER MOTORS!
Thanks for sharing the videos
Verry nice!
Do you remember what your feeds/speeds was on the holes and profile cuts? :-) Nice Cuts :-) Thank You for the video.
The trick is to use a vacuum cleaner to suck up the debris. I took a flexible hose, and set up a clamp to hold it close to the end mill. I even made a small shroud that surrounds the tool gets debris even from all around.
can you die cut something like this with a plunge router or table top router or trim router which do you suggest? i am new to this and harbor freights offers those items. i pretty much have a 14x16 piece of plexi that i need to die cut some ovals thank you for your time!
Nice and smooth 😊
Hi, could you please advise what king of end mill are you using to cut and where could I find it ? THANK YOU
I think The user here was using the Single flute end mill..That was the best on cutting Cast And Extruded Acrylic.
perfect
Merhaba Atakan, hocam kesim baya guzel. Hangi ucakta kullaniliyor?
@HomeCockpitSolutions
7 жыл бұрын
bu kesilen parca 737 nin flap gostergesi cami icindi ama cok eski bir calisma ve tasarim. suan yenisini yaptim yakin zamanda videosunu atarim
@BullBosphorus
7 жыл бұрын
GuZel merak ettim. Bekliyorum videoyu
So good mechine cutting
which tip did you use for the cut?
It almost looks like you should take smaller passes at a higher speed, did you find that to be the case? Just heard some chattering on the first pass.
I use Onsrud 1 flute bits and don't get edge finish like you have. My cut edge is not clear like that . Please what the name of the bit and where you got it and what size. I'm using .25" Onsrud #63-622
what kind of cutter that you use for cutting the acrylic sir?
what drill bit do you use?
О боже как же я хочу, фрезерный станок. Но я не хочу брать кредит.
Ok, now I'm curious..... What is the part for?
I will love to have those machines am a sign practitioner, thank you
Great
Where did you bought this, or parts how to build
Does it matter what type of acrylic its used?
SHOW!!!!
nice.... i just to have a 30x40 i miss it.
Awesome idea1
Ohhh I get it, The video is 4xF>>
شكرا
till what size we can use
I'd like ta take my SNES apart and 3-D print its case transparent :D
Hey I was wondering could I get you to do a little project for out of acrylic
NICE, BEAUTIFUL AND CLEAN WORK , THANKS FOR SHARING IT. QUESTIONS ; WHAT KIND OF MACHINE AND PROGRAM YOU ARE USING , WHY TOO MANY CUTS ON IT ?
@zusurs
9 жыл бұрын
I presume so much cuts are done to minimize heat-stress on material, as well as this small milling head isn't durable enough to drill whole thickness of material at once.
@franjalen
9 жыл бұрын
Artūrs Savickis Thanks for your answer .....but I'm not agree with you.....there are too many questions in the air , but the video and the work it looks interesting . Greetings.
what is the speed you are using for tool and moving? i'm having problems with melting :/
@FoivouDady
4 жыл бұрын
Melting is a big problem. To solve , im using 0,4mm per pass, fast feed to prevent melting and MDF bit single flute. Compresed air on cutting point helps also.
@1slippy
3 жыл бұрын
I was going to say he probably gets away with it by making several passes. Do you have a veritable speed control on the motor or is it just one speed? If you can lower the RPM and increase the table feed you could make less passes. It looks like the boy is a .062 dia if you could lower the feed use a .093.
@LordAnubis0909
3 жыл бұрын
I will give it a try. I can change speed on the tool. Just .made new mini cnc to test
Merhaba; Böyle bir makineyle 3mm pleksi kesimi yapılabilinir mi? Kaçlık nasıl bir uç kullanmak gerekir?
bu cihazin adi nedir? birde kesilen yerler puruzlu kaliyor mu acba?
У меня стекло плавится ... I have the glass melts ...
Mantaaaab 👍
Felt like I was at the dentist for a second. PTSD
Mere pass acrylic ki sit hai bahot Sari kya price
End mill?
what's the manufacture of the bit and what size diameter is it. and what's the model number of the bit
@jimealase2848
7 жыл бұрын
Great
@jimealase2848
7 жыл бұрын
good for all
@manwar512
6 жыл бұрын
lophole7
good job ^^
Eline sağlık. bende bir cnc yaptım ama plexy eriyip uca yapışıyor bunu onune nasil gecerim? uç tek fülüt cnc ucu olmasına ragmen.
@HomeCockpitSolutions
7 жыл бұрын
teşekkür ederim. öncelikle spindle devrini düşürebilirsin. gene erime yapıp uca sarıyorsa ilerleme hızını arttırabilirsin. dalmayı 0.5mm deneyebilirsin
What bit is used. Diameter? Flutes? Type?
good job, thanks
Can any one please help with the software and instruction how to use the laser on the 2418. It was supposed to be with the machine or on the disc supplied but there is no instruction. I have learnt how to use the engraver by trial and error. If you know how to locate the instruction on the disc for the laser could you point me in that direction. If not can you please assist with an explanation on how to use the laser and what other free software maybe available for the laser. The pictorials and you tube information is either in Chinese or Russian. Mmmmmmmmmmmmmmmm. Bit of a problem for me. Simple explanations please as I am just a simple Non University Aussie. David.
how much does this machine cost
I need this thing
I need to know the prices
Me puede indicar cómo se llama esa máquina?
Como que se tardo mucho para hacer ese corte
Ser lesar engraving acrylic kat leta hai
Acrylic typically melts when being drilled with a conventional drill bit. Why doesn't it melt when using a spindle bit, especially without coolant? I would think it would. Thanks!
@THOMASTHESAILOR
6 жыл бұрын
If you watch the first few seconds of the video, before he starts the spindle, you can see, he is using a "Roughing" endmill, or some call it a "Corncob" endmill. It has bumps on it, that reduces the area of contact between the cutter and material, therefore, reduces friction/Heat. also, rpms have a lot to do with it. It's all about friction.. My cnc router won't go that slow..
Wow awesome machine. Could you advise where you got your bit from
@HomeCockpitSolutions
5 жыл бұрын
i am living in Turkey. from local store
@soyebravat8903
5 жыл бұрын
@@HomeCockpitSolutions hey thanks. I would luv to try and cut acrylic. I make signs and have so many board's just laying here and off cuts. Might as well try and cut something. Do u have the details of the bit or can u advise the name of the shop or if they online?
@HomeCockpitSolutions
5 жыл бұрын
they dont have online shop. you have to but single flute cutter. you can choice diameter what you want. this cutter is single flute 2.5mm diameter and 10mm cutting lenght.
Hi, great video. I would like to know what is the XY advance speed, what is the Z axis step down and what is the spindle rpm? Thank you very much.
@HomeCockpitSolutions
8 жыл бұрын
+Anderson Lima xy 600mm z is 100mm
@ronniepaulinc
8 жыл бұрын
in 1/4 inch you should make a shallow roughing passing with 2 follow up depth passes and a finish path.. Speed is dificult to say with each cnc, you want to pass as fast as you can but vary your spindle speed to ensure your are not creating enough heat to melt
nice setup. Do you have you instructions on how to build this? I'm looking on most of the sites and many are broken links and missing how to's and stuff..
@longxingacrylic1691
10 жыл бұрын
We are acrylic manufactory from China,my skype is king203344 Email:longxingacrylic@163.com
@zusurs
9 жыл бұрын
Belive me - if you have no expirience in building CNC machines (and your question points out you don't), buying cheap-ass (we are still talking for about ~1600$ for 30 by 30 cm (square foot) of working area) small CNC from China will be LOT cheaper and less time consuming than build your own.
@seanpain4
9 жыл бұрын
Artūrs Savickis It may be easier but not way is it less expensive
@zusurs
9 жыл бұрын
Sean Pain It is. If you account all parts, electronics, tools (programming kits and microcontrollers necessary), software and all other hardware, not even mentioning time necesary to learn and build everything, as well as multiple failed attempts at first, buying ready-to-use unit IS cheaper.
@HomeCockpitSolutions
9 жыл бұрын
Artūrs Savickis absolutely true..
could i use a dremel tool for this one? what bit should i use?
@HomeCockpitSolutions
8 жыл бұрын
yes you can use dremel but i have to choose dremel with variable speed. you have to choose single flute end mill for pleskiglass, acrylic
Tool bit link please??
we cut acrylic up to 10mm thick single pass, your chip load is Far to low. go faster 4000mm/m
@HomeCockpitSolutions
6 жыл бұрын
Chris Bottrell Photography you are so smart :D but this is mdf amateur cnc ;)
@hyperhektor7733
5 жыл бұрын
lol sure, but did you already tried to max out the machine? even when its a hobby machine it doesnt mean you can try to go faster.
@nicolezhang2340
5 жыл бұрын
pls add my whatsup/wechat: 008613075365628
Can u build me one
i need to see the result, clean cut or not.
@nicolezhang2340
5 жыл бұрын
you wnat clean cut? my whatsup/wehcat: 008613075365628
Sa kardeşim 6mm hangi takım ucu tavsiye edersin birde Spindel ayarını ögrenebilimiyim pleksiyi eritmemesi için
@HomeCockpitSolutions
Жыл бұрын
selam. 6mm çap olacaksa plekside mutlaka tek ağızlı bıçak kullanman gerek. kullandığın kesici ucun çapına göre ilerleme hızı ve spindle devri ayarlaman lazım. mesela 800mm/dk ilerleme ile 10 bin devir spindle ile rahat kesmesi lazım 3mm çapında uç ile. tabi çap değişince bunlar da değişir. keserkenki gelen sesi de iyi anlaman lazım makinenin rahat kestiğini anlamalısın
@neon_led4you
Жыл бұрын
@@HomeCockpitSolutions hocam benim yapmak istediğim 5mm pleksi üzerine 2.5m harf kazıma yani komple kesim değil çift üçlü bıçak kullanıyorum bu türlü ayar tutturamadım sürekli pleksiyi eritiyor
@HomeCockpitSolutions
Жыл бұрын
@@neon_led4you o zaman spindle devri çok yüksek deviri düşürün
@neon_led4you
Жыл бұрын
@@HomeCockpitSolutions spindel 8000 Feedrate 3000 Plunge 600
Atakan bey merhaba corsair 465x beyaz kasamın temperli camını kırdım ve yenisini bulamıyorum ölçü versem ve resim atsam sizin bana 4mm kalınlığında temperli şekilde yapıp gönderme durumunuz olabilir mi?
@HomeCockpitSolutions
3 жыл бұрын
Maalesef
I have tinnitus now. A different audio track and a slightly higher camera angle would make this video better. Not hating, just saying.
@lass-inangeles7564
8 жыл бұрын
+Nic Stroud Ha, ha, ha! Me too! My ears are buzzing. Some truth to using hearing protection, eh?
i working with acryling. and is not good seting and very slowly. i use 3.17mm - 1150 mm/min and depth 1.5mm , ot 12 000. better that this . i am sure
If you use tap option, no need use finger
Which Software your using?
@hussainali8909
Жыл бұрын
If, can you share how to setting CNC machine with software
You are cutting it wrong direction. You get better finish when the flute hits the material as you move forward. In you case you'd get the better finish on the outside part.
slm Atakan bey kulandiniz frezze ucu ne marka?
@HomeCockpitSolutions
3 жыл бұрын
inanin markasini hatirlamiyorum.
that's nice, "4X faster" that what,?
@dannyspencer933
6 жыл бұрын
the video was speeded up by 4x rather then watching it cut for 30 mins
At last the item melted and bit was broken plus the spindle caught fire. He failed in making WHATEVER he was making at WHATEVER machine settings
@HomeCockpitSolutions
7 жыл бұрын
your machine your problem. i wrote my settings. you can look down
@tomjdesigns1280
7 жыл бұрын
Where have you? Can't find any setting
What machine is he using? I'm looking to invest for fabricating grills for PCs.
@HomeCockpitSolutions
8 жыл бұрын
Cnc
@DavidBixler
8 жыл бұрын
Duh. What make/model?
@HomeCockpitSolutions
8 жыл бұрын
+David Bixler i made it
@DavidBixler
8 жыл бұрын
You made that machine? Christ how?
@HomeCockpitSolutions
8 жыл бұрын
+David Bixler google it. you can find any information
Hello sir, Which tool do you use for acralic no. Cutting?
@riiyung1081
3 жыл бұрын
kzread.info/dash/bejne/eY2KyM2znM-6pLw.html Acrylic cutting Whatsapp:+86 15624071968
Merhaba bende bir cnc yaptım 300w spindle motor siparişi verdim gücü nasıl acaba bi fikir verirmisiniz sizin kullandığınız motor kaç w birde
@HomeCockpitSolutions
6 жыл бұрын
Doğru İletişim benim bu videodaki spindle 750w ama simdi buyuk makinemde 2.2kw spindle kullaniyorum. Dusuk devirlerde elinizle durdurmaniz mumkun degil. O yuzden demir ve aluminyum islemek icin yuksek torklu spindle kullanmak gerekir ama plastik ve ufak capli isler yapilacaksa 300 de yeter 750 w da yeter
@dogruiletisim
6 жыл бұрын
Atakan Şenyurt çok sagol peki bu yaptığın işi 300w yApabilirmi
@HomeCockpitSolutions
6 жыл бұрын
Yapar
what bit did you use?? and what speed?
@andreeca
10 жыл бұрын
I'm searching for the same answer :D the speed... P.S. Steven, the bit is single flute end mill, specially for acrylic.
@StevenKiberton
10 жыл бұрын
andreeca Many thanks It looks like the video is speeded up also I have just bought a C02 laser CNC so I will do most of my cutting on that but the working area is only 300x300mm where as my CNC Mill is 1000x1000mm so I will invest in a few of those single flute end mill bits and see what I can get
@HomeCockpitSolutions
10 жыл бұрын
Steven Kiberton this is single flute end mill for acrylic. video 4x faster. spindle rpm 11000 and feed rate 600mm
@StevenKiberton
10 жыл бұрын
Nice work and thank you :)
is it extruded acrylic or cast acrylic?
@SisiCheng-nz1jg
3 ай бұрын
Do u need thin acrylic sheet
Why is it not melting to the bit!?
@henk6172
9 жыл бұрын
Because plexiglass is a really soft material, moving to fast would melt the plexiglass, not the bit.
@naticristellavi8236
8 жыл бұрын
+Harm Prins Exactly, that is what happen to me the acrylic or plexiglass melts and adhere to the bit. Is a special bit for doing this? How can I prevent the melted acrylic from adhere to the bit? Thanks
@henk6172
8 жыл бұрын
Naticris Tellavi there are no special bits to cut acrilyc. you just have to keep it from melting. to produce the least heat, your bit has to be sharp, and most important, you don't want to go too fast. the faster you go, the more heat you produce. there are some great feed and speed recipes on the internet.
@naticristellavi8236
8 жыл бұрын
+Harm Prins Thank you. I went to Dremel.com and read the description on the Tugnsten (don't know the spelling) and those bits are made to last longer and designed to produce less heat.
@alexmarion8171
8 жыл бұрын
+MrStankoman because he is using cast acrylic sheet
posisi kamera salah cuk, kagak kelihatan...
can you please to shared the plans
@HomeCockpitSolutions
7 жыл бұрын
which plans ?
hello all, i want to cut ABS & PP material by using robot. the thickness is near about 6 mm. please suggest me the motor speed type of cutting machine and approximately what should i have to put the speed of robot.
@kendrickxy1774
7 жыл бұрын
I think it should not be a problem cutting it. But maybe if you have an heat gun you should follow the drill with that heat gun (It should be easier to cut). But beware of the bad smell, because it's 100% chemical
A sealed-CO2 laser would cut and polish in a single pass.
where is the best place to buy acrylic
@TylerHarney
9 жыл бұрын
Drr magneto Mcmaster-Carr is where I get mine.
what the name of the drill bit you've using?
What is the machine name?
@HomeCockpitSolutions
Жыл бұрын
diy mdf cnc machine
you dont need to grind the material :)
@nicolezhang2340
5 жыл бұрын
Yes, our Ld-6000 is suitable for cutting acrylic. my whatsup/wechat: 008613075365628
Thickness 6mm??
@HomeCockpitSolutions
Жыл бұрын
5mm
how much is it cost,i need to get one
@HomeCockpitSolutions
6 жыл бұрын
for what ??
@abertkong4321
6 жыл бұрын
hi dear, we also can offer this machine, please contact me wahtsapp+8617153941009
faster? what was it before? That is dead slow, what is the chip load 0.005? Can't get any tool life without a good chip load.
@HomeCockpitSolutions
7 жыл бұрын
yes x4 faster. video edited to x4 faster from actual speed. if you look below comment you can see some information ok ?
silly brush just pushes the shavings elsewhere; get a vacuum system
Hi, can You tell what configuration are You using, as: 1) tool diameter and nº of flute. 2) rpm 3) feed rate 4) deep of cut Thanks
@HomeCockpitSolutions
7 жыл бұрын
2mm one flute 12.000rpm 600mm/min feed and 1mm deep of cut
@francispp81
7 жыл бұрын
Eduardo Braga estou apanhando para cortar um acrílico de 5mm aqui rss
why not just have a fan blowing on it
@lostallmymirth
8 жыл бұрын
+Bill Morris With the use of a shop vac, removal as well as disposal of all plastic swarf will be performed in one operation.
you did this in way too many passes.. I would have used a feed rate of around 3000mm/m with a plunge rate of half that, at that rate you could definitely do it in one pass but would do 2 just to be sure of a clean finish.
That was a home made CNC ??????????????????????????????????????????????????????
@HomeCockpitSolutions
3 жыл бұрын
Yes
Thumbs down due to lack of any information. Showcase videos are only useful if you share information about what you're doing and how you're doing it.