thank you, very helpful for my upcoming test!

Power knee. I hope you appreciate that.

@branodeleo5960

6 ай бұрын

Yea that sounds amazing.

@restoration-projects

6 ай бұрын

It is a battery powered drill with an adapter that i made that goes where the crank hooks in

@jakecarter4407

6 ай бұрын

@restoration-projects ahh. Cool. that's better than hand cranking.

Niiiiiiiiiiiiiice

@restoration-projects

6 ай бұрын

Thanks

I wouldn’t trust the knuckle scale to give me a true angle. I’ve seen them off as much as 1 degree. Always tram to a correctly set sine bar.

lol did you stencil paint kurt on that vice?

@useditem_tk

Жыл бұрын

He did lol

@lintelle2382

10 ай бұрын

looks engraved

@martinpanev6651

7 ай бұрын

That would be hilarious, but sadly, no. The old Kurt vices had embossed letters that were cast unto the metal prior to machining. He just painted the inside.

What happened to traming in that head to a sine plate ?

@restoration-projects

6 ай бұрын

It was a non critical part so I just used the scale on the mill

@vwbrinker

6 ай бұрын

I was gonna say the same thing

That is a cool machine. So what's the difference between a Bridgeport vs Milling Machine?

@RW0-

8 ай бұрын

They are the same. Bridgeport is a milling machine. It’s just a famous manufacturer of milling machines.

@shaneschuller2513

8 ай бұрын

@@RW0- Thank you 🙏

if you used the degree wheel on the mill your 8 is off

That machine sounds like somebody is murdering it. Why not just sidemill that with an M42 rougher? Those giant shoulder mills are all just glorified fly cutters, I would never use them for cutting a bevel. If they are used for hogging material they kill the mill head. I do a lot of shipyard prototrak work and M42 roughers + coolant is the most economic way to do low volume work.

@restoration-projects

6 ай бұрын

I will have to try that. I dont have any formal training so these videos are in a way documenting my learning journey. I never thought about the stress that it puts on the mill head. Thanks for the tip

@InchFab

Ай бұрын

Can you explain this a little more?

@phalanyx3478

Ай бұрын

@@InchFab Inserts dont have the same cutting geometry as a ground end mill. They are more blunt at the edge and behind the edge their angle is more obtuse like a splitting maul vs. a kitchen knife. Solid carbide tools are this way too when compared to HSS/M42. M42 is HSS with 8% cobalt alloyed in. I had 4 35* bevels to mill on 2" thick plate and I did those all sidemilling with a single 3" long 3/4" M42 rougher. M42 end mills are also quite cheap on ebay, great tooling for smaller shops working with lesser machines that dont need short cycle times.

@InchFab

Ай бұрын

@@phalanyx3478 got it, thank you.

Is that a rotary?

Why is the drawbar so long? 😂

@restoration-projects

6 ай бұрын

I"m not sure exactly, it came that way

@db747

4 ай бұрын

When you install the 90 degree head, the quil is lowered down. The 90 degree head clamps to the exposed quil after it is tightening into the collet taper. If the draw bar was much shorter than it is, you would not be able to tighten it with the quil down for the 90 degree head.

@phalanyx3478

Ай бұрын

Quillmaster JA w/ right angle attachment. Still an extremely valuable bridgeport accessory.