Since Cleetus and James have the MTN DEW & BUSCH wraps, respectively. You guys def have to do a TWISTED TEA wrap. 100%

@Toxic88088

2 жыл бұрын

It would be monster - VTEC wrap cuz Kyle.

@seankelly8225

2 жыл бұрын

Coca-Cola pfi wrap

@noneyabusiness1359

2 жыл бұрын

Baja Blast

@bangthemgears9999

2 жыл бұрын

They ain’t getting paid for the promo, not sure why they even did it to begin with. I would do boostedboiz wrap all over it. F the free sponsorship

@brandonbritt99

2 жыл бұрын

twisted tea wrap 1,000 %

Kyle, you can always install nutzerts into boat frame. Just use plated ones not stainless because stainless will make aluminum oxidize way faster than just regular steel.

@Skwisgar2322

2 жыл бұрын

Good old galvanic series.

@joshua_J

2 жыл бұрын

Please more people like this so Kyle sees it

@mikeyalwayslikesit

2 жыл бұрын

#facts

@leadfoot8593

2 жыл бұрын

Is cutting mounts out of al and welding them in a bad thing?

@scotttod6954

2 жыл бұрын

He could just fish the bolts in and face them up. They make wires that are wound the same thread pitch for bolts then you just pull the wire though and pull the bolt in. I have installed a bunch of 5th wheel hitches and the kits come with the wires to fish bolts into frame members.

Love the progress! One word about the 1310 and the jet pump. The engine needs to have a minimum angle(crank) of 2* compared to the jet drive shaft. Otherwise the U-joints will wear unevenly and will fail prematurely. Ask Finnegan too, he'll confirm

@otm646

2 жыл бұрын

You can get away with less, I've had an installations run for thousands of hours at one degree. I've seen some industrially that are even less, close to a half a degree running without issue.

@stuwest5862

2 жыл бұрын

.5 degrees is all you need to rotate the needle bearings.

@1MrPooney

2 жыл бұрын

Heads up if you wanna make the ⁰ symbol just bold down the 0 on your phone or on a windows P ALT + 0176

@tannersorgenfrey7566

2 жыл бұрын

@@1MrPooney °

@c-dubmediallc4933

2 жыл бұрын

@@1MrPooney no on Android that is just an exponent. Like ⁹ or ⁸ this is the degree symbol ° not ⁰

Been a boat mechanic in Virginia for 12 years. When I see a boat from Florida I run. Don't underestimate electrolysis caused by dissimilar metals and that humidity and salinity. Ground every component and have sacrificial anodes.

@degax203

2 жыл бұрын

zinc is life

the steal bolts going into the aluminum will be your problem, they WILL bond with the aluminum, very fast when wet. Maybe you need to put on a sacrificial anode by the engine mounts. Just to be sure the bolts will not bond with the aluminum. They will break when removing them in as few as one year. Ask any boat owner. Sacrificial Anode will stop that and its cheap insurance.

@opossom1968

2 жыл бұрын

@Richard Brown Yes and in wet conditions it happens fast.

Definitely should do some billet aluminum mounts for jet boat engine. Look up galvanic corrosion. You'd be surprised how fast it'll corrode especially with salt water. You don't want to have to replace the bottom of the boat in a couple years

@BUD420MAN

2 жыл бұрын

I wonder if a sacrificial zinc rod would help or some kind of dielectric grease would help. Ideally you would want remake the bottom mounts out of aluminum.. that way the bushing/crush sleeve in the rubber mount and the bolt would be the only thing touching making it easy to monitor and replace

@Patricks_Projects

2 жыл бұрын

Just put thin rubbersheet in between and powedercoat them. Should hold up a couple of years.

@Matty.Hill_87

2 жыл бұрын

@@Patricks_Projects that's the route I'd go as well, just isolate the steel and aluminium from each other

@dcskate1022

2 жыл бұрын

Probably the worst thing you could do. You’d be attaching a vibrator to a tin can with solid mounts.

@opossom1968

2 жыл бұрын

ZINC anodes for Salt water. Magnesium for Fresh water. IF not its going to get fun really quickly. You see when the corrosion starts to show, in a few months, little problems with the ground between the engine and boat hull will start. Some times the ground can burn through the aluminum, but mostly the SHOCKS will start. Kyle will have wet feet touching the hull of the boat, and then touch anther part of the boat like say the wheel and get shocked, people will start to notice a shock when walking up and touching the boat, even swimmers when grabbing the boat will get a shock. Then there is the removing of the steal bolts from the aluminum. In less then a year, without anodes, there will be no removing the bolts. they will break. Look at my back ground pic, tell me how i know, been boating all my life. No replacement for piratical experience. I have anodes on my truck, because it has Aluminum touching steal. I guess manufactures did not listen to the guy talking about galvanic corrosion.

I'd cut out the thin top and sides of those floor frame channels an inch or 2 longer than the mounts, then drop in some solid billet rectangles the thickness/size of the OG brace. Weld em in place then tap into the thick stuff like you had mentioned... Easy Peasy and much more solid transfer of energy to the bottom and less chance of vibration issues / weld fractures.

I love “test and tune”. Sht flying everywhere and using some of Brent’s terminology “making some jam”. Enjoy everything you guys do.

I love how far this channel has come but it all still feels original and genuine, some of the other channels I watch have progressed but have lost the feel of the channel that got me interested in the 1st place, keep it up guys.

@dellerb

2 жыл бұрын

My thoughts exactly!

I wonder if anyone noticed the red C5 Corvette in the background when Kyle was looking underneath the van. That might be the baby he's talking about

@stevenmcc2119

2 жыл бұрын

I seent it 🥸😶‍🌫️👀

@rainwatson4105

2 жыл бұрын

Hopefully he puts an FDF angle kit on it 🥵

@burtonwhitaker6849

2 жыл бұрын

I was going through the comments to see if anyone else seen it too

@patricktowell1033

2 жыл бұрын

@8:35 been scrolling through the comments and thought I was the only who saw it

@dylanburch5379

2 жыл бұрын

I was about to write this like can we just talk about that for a second darn

The boats definitely going to be kool, And far as mounting the steel plates to the aluminum haul just use rubber sheets and make a gasket to sandwich between the 2 it'll help some with vibrations transferring and corrosion

If you have any issues. You should mill aluminum sqaure blocks to bottom mounts to use with the same width as you motor side mounts that way you can weld the aluminum bottom halves right to the boat . It would be super easy to make them and use them with the top half of the mounts you have already made.

Love the jet boat build series. I would like to suggest another idea for the motor mounts. instead of drilling and tapping thin aluminum stringers, look into installing a heavy duty nutsert rivits. I use these in body up fitter shop i manage, and they hold great

I love the fact that your k swapping a jet boat when most just convert from other water craft, same as the Sandrail v6 honda engine making far more power and torque than most side-by-sides with more suspension travel aswell. You can buy something but converting these things with engines that can easily make crazy power even in boosted stock form is far more fun and offers more speed and ideas down the line.

@leadfoot8593

2 жыл бұрын

Phong woulda used a modified cv joint from the pile instead of that bought not built piece lol.

@EasyGoingLife101

2 жыл бұрын

Not to mention a nice side by side is 20-30k or buying a motor out of a skidoo is 5k or more. Way cheaper and way for fun and cool to see work. I’m jealous.

@EasyGoingLife101

2 жыл бұрын

@@leadfoot8593 we all would have. Haha

@beany1987

2 жыл бұрын

@@leadfoot8593 yes Kyle and wyatt are trying to do things better now so getting some parts to a high standard when the will probably turbo it is logical. They could make something but it would probably break and you wouldn't want to be sitting on that aluminum seat with a turbo k series doing at any speed with junky parts underneath you that's for sure. Imagine a exposed flywheel coming lose of backing out its bolts.

@TheSupersample

2 жыл бұрын

I love the sandrail and have buggies myself but there is no chance that rail would hang with a new rzr or can am suspension wise lol but on relatively smooth sand and not a super short run it would destroy them in a drag race.

Nice little update! Hope the jet boat get a good wrap put on her like the Cleetus boys. I think you should keep the same theme and do a Twisted Monster. Keep on build and turning wrenches. ✌🏼

Hell yeah you know it’s going to be a good day when Kyle drops a video much love brother

you guys are doing awesome things!! wyatt is a huge game changer to the channel!

Wyat should try a capacitor on that power steering pump. It might help it keep up during the more aggressive turning. I think Taylor Ray is doing something like that in his new drift vet build. He may have the knowledge you need for your steering pump.

@wcovey25

2 жыл бұрын

good idea

@oscardeltoro898

2 жыл бұрын

From the research many have done it's been documented that the pump uses CAN network to work at 100%. With just ignition only like Kyle and many have done makes the pump work in limp mode which just works at 70%. Enough to work for many however it's the CAN input the only fix for this pump to work as intended.

For the engine mount to boat frame fasteners, maybe consider some threaded inserts. The type that are installed like a rivet. They would have much better thread engagement. Also, installing a zinc anode will help protect from galvanic corrosion, from the steel/aluminum contact.

Great stuff BOIZ! Can't wait to see the Rowdyssey trolling the streets! Wyatt's truck is looking sweet! The boat is coming together nicely! Thanks for sharing BOIZ!

Congratulations on the baby Wyatt! I hear you having a son too. Dang you and Kyle must have found twins.

@RubbishFPS

2 жыл бұрын

They adopted a child of their own...

@andwooo9460

2 жыл бұрын

Ha 😂

@ahfreebird

2 жыл бұрын

@@RubbishFPS Get ready for the diesel Hondas in about 15 years!

@i-_-am-_-g1467

2 жыл бұрын

@@ahfreebirdnah its gonna be the future remember... tesla swaps inbound

@dj_ps_gamer1324

2 жыл бұрын

😂😂😂😂😂

Universal driveshaft is awesome, last year a company driver needed a driveshaft done like asap and they got it done.

HOLY FAWK!!!!!!!!! That pull after you tightened the intercooler pipe was SNAPPY & JAZZY WITH IT BABY‼️

Omg y’all need to sit on the on-ramps to highway again but with the van LoL 😂

How long you guys think it will take him to get bored of his new girlfriend and K Swap her ?

@lr7974

2 жыл бұрын

Once she's down a hole

@pinduckyfarms4748

2 жыл бұрын

Depends on how her two step sounds

@INORBET

2 жыл бұрын

@@pinduckyfarms4748 😂👌🏼

@i-_-am-_-g1467

2 жыл бұрын

The *real* question is which will take longer Kyle popping the question or Kyle hitting 3rd gear?

@jeffreis5194

2 жыл бұрын

She came stock with a k24

You could always cut out the sections below the mounts and weld nuts to the underside of the plates with a plate wedged and welded in between the 4 nuts across the center, then weld the nutted plates back into the boat. This will give you more threads for the mount-boat bolts and the plate wedged between the 4 nuts will aid in stopping the welds holding the nuts on from cracking or breaking because the nut will be pressing up against the plate, insurance so you never have to cut those plates back out to reweld the nuts on.

@BeardMan01

2 жыл бұрын

Stainless Nutserts are easier. Probably not cheaper though.

@MillionairX

2 жыл бұрын

@@BeardMan01 yah but being engine mount bolts, a feller will torque on those till the tenden pops and certs tend to spin over time. Over engineer shit like this so its done once.

@BeardMan01

2 жыл бұрын

@@MillionairX Factory vehicles with aluminum unibodies use Nutserts all the time for all sorts of critical components. They are absolutely up to the task, especially if installed correctly.

@eldonerc2524

2 жыл бұрын

@@BeardMan01 you don't want stainless in contact with aluminum, the nickel in stainless will eat the aluminum fast.

@BeardMan01

2 жыл бұрын

@@eldonerc2524 Not with a zinc tab mounted nearby, as there should be anyway.

Hell yeah. Can't wait to see everything up and running.

Love it! Thanks for sharing. No clue if this would work or not to hold that K in place. There is a thing called a rivnut. Maybe that would work. Thanks for the videos man. It's nice to see some coom stuff and just take a brake for a hard few weeks. Much love. God Bless.

Make sure to do close loop cooling with a heat exchanger

@zachmoyer1849

2 жыл бұрын

lol just commented this

@davidr1997

2 жыл бұрын

This would be the smart move!! 👍🏼👍🏼

Man you guys are on another level!!! Seen these boats years ago! And yep drop a K-Series in it! Def didn't think it would be this involved...! Glad you guys are doing the build. Tom never made a build that I can remember on his boat. With his K-Series, only showed him dynoing it on PFI Speed channel. Hopefully when your done you guys can both put them neck to neck in a heads up race! Really do enjoy watching your builds. Can't wait to see more!!! OG subscriber, just enjoy the content you put out...!

Maybe you could cut small square of rubber mat the shape of the mounts and slide it between so you have some vibration/noise dampening. Just from my experience I have seen some drone from solid mounts. Cannot wait to see this thing in the water, It' going to be epic!

looking good! you might want to fab up a bell housing for that thing so it doesn't sling grease all over the place from the slip yoke...

Add this to the intercooler series 😄

Kyle's adopting Brent as his son....

@FastLaneLyfe

2 жыл бұрын

Wait so Shane will be his grandson.

@dj_ps_gamer1324

2 жыл бұрын

😂😂😂😂 I'm done

@RubbishFPS

2 жыл бұрын

Just thought him and Wyatt were going to adopt a kid

Rowdessy is getting motivation going for my astro, yeah, it's going to be ls swapped, but I'm thinking it may be AWD. If the k series is too heavy, Honda put vtec on a few bikes back on the day, vfr 800 comes to mind

@eldonerc2524

2 жыл бұрын

Wonder if he's still got that golf cart they built with cleatus? 🤔

You can still put in the aluminum blocks. Just cut holes and recess them. Then use a sacrificial anode as others suggested along with a lot of anti-sneeze on the bolts. Making sure the block is thick enough so the bolts don't have a hole at the bottom would help too.

You can tell Wyatt has been watching a lot of rob dahm videos

hell yes i can’t wait to see it rip on the water

I freaking love u catz. not anything weird, but seriously u guys put the biggest smile on me, and my family's faces! I hope ya'll never change, or skip a beat.

I'm a welder fabricator for almost 20 years, and I used to work for a company that did kingpins and all sort of attachments for trucks. When we had to joint parts made from steel, to parts made from aluminum, we were laying duct tape on one of the surface before sandwiching the 2 parts together, this way we were avoiding corrosion between the 2! Steel in contact with aluminum in salt environment will just make both metals rott! You should definitely use this route. It's simple and will save you lots of headaches and time in the future! Also for the engine mounts, you could simply scribe around the steel squares, remove the engine, cut the square holes and then insert 1/2" or 1" thick blocks inside the holes that you could weld solid and safely tap. IMO tapping engine mounts in 1/4" thick aluminum is borderline solid enough!

bro we need an NSX NIGHTS series where you hunt em down at night in mexico.... in the nsx

Pfi is moving to Florida I'm calling it now

@ChrisBeevor0511

2 жыл бұрын

May be the reason that Shaun and his brother Todd have said their goodbyes to Brent and PFI 🤔

@hops004

2 жыл бұрын

Now that would be gangster

Kyle, it’s best practice to have 1-1/2x the bolt diameter has your thread depth. So if you are planning to use a 3/8”diameter bolt then you will need about .518” of formed thread for the bolt to engage into. If possible a nut on the backside would be better than only have 2-3 threads engaging on each bolt. And it would not be surprising to see the aluminum frame rail fail quickly putting torque to that thin material. A nutsert is actually probably the easiest and not a bad solution at this point. But I’d recommend rebuilding your mount to be able to spread your load down the frame rails with thicker material that you can run a proper thread into. Best of luck! 👍

Kyle and Wyatt look at a rack from a 2020 f150 it's all electronic. It will also cut down some weight. Keep it up y'all are awesome.

"I'm gonna put this e85 on the passenger seat" precedes to litterally poor e85 onto the seat. 🤣

Oh so theres a possible boosted baby on the way !!!

Great content miss the cars ripping nice jet boat and really curious to see what is going on we are waiting to hear of lol 😆 be safe guys.

thumbs up for jet boat content 👍 can't wait to see her finished

Kyle is getting married, bet.

Can’t wait for the K SWAP PORCHE build!!!!!! 💛🔥🤘🏽

Better start paying your employee good and showing more progress on his truck. He seems like a good guy to have around. Smart and works hard

Dyslexia 4:17. Cainted the page. Love it. I have the same affliction.

He's getting a dog or maybe a turtle 🐢 😆

C5 corvette @8:30 @6:16

down under South Australia a dude is doing a 2JZ Honda Odyssey swap RWD with 350Z suspension setup..his youtube channel is Low Standards .....................................i'm hooked on the jet boat ...............................

You are one of the only people that actually seams to read comments. You do you and thank you for the content.

Anyone notice he never said no to having a baby😂😂

@dj_ps_gamer1324

2 жыл бұрын

😂😂 facts

@FinnaBin

2 жыл бұрын

Was gonna say that

@FastLaneLyfe

2 жыл бұрын

He doesn’t look pregnant 🫃 tho

@dj_ps_gamer1324

2 жыл бұрын

@@FastLaneLyfe 😂😂

4:14 "cainted the page" Lmao good one

@turnerclews5331

2 жыл бұрын

Thought I was the only one who heard it had to look through the comments

@andwooo9460

2 жыл бұрын

My boys. He's been saying that since the Colorado house days hahaha.

@paperboy371

2 жыл бұрын

He also said he was retiring that little inside joke ☺️

@turnerclews5331

2 жыл бұрын

@@andwooo9460 imma be completely honest honest I started watching a few months ag

Awesome job guys.

that mini jet boat is gonna be an absolute MENACE!!!! Can't wait to see it in the water! :D

Is it gonna be turbo or supercharged? Cause I would love to see a supercharger on your guys' channel!

@Evoke_1

2 жыл бұрын

I'm guessing turbo. No seat clearance for the super charger

@martindinner3621

2 жыл бұрын

The initial plan is NA VTech, with turbo later.

I wanna see this jet boat ripping so bad !

@pw383426

2 жыл бұрын

Me too! That orange PFI powered tunnel hull never ended up on youtube

Get a full set of EBC Red break pads for the Porsche . They work great and will cut way down on the break dust that you are getting on your rims. As for the engine mounts for the boat, You can simply remake the lower portion of the mount out of Aluminum. The rubber will isolate the steel portion from touching the aluminum portion. So just aluminum stands that can be welded directly to the boats hull or bolted if you prefer to have them removable.

I did that conversion to my 93 C4 Love it.

I'm betting there's a new lady in your life

@fallenhobbit6554

2 жыл бұрын

has been for awhile. I saw her in the background at a few events

Summer is around the corner, keep at boys! Super pumped for you.

Man get a piece of foam wrapped around the window frame in case of flying forward then get water proof material and buttons and wrap the foam with that so looks nice aswell

Wyatt keep your channel and your work poppin, you got the skill.

Awesome vid guys. So pumped about Wyatt’s truck and the jetboat

Man that will be a lot of HP for the little jet boat for sure. Maybe later you can put the big alluminnum block in their to tap to.

Nutsert the bolts into the aluminum that new tool Taylor Ray has is badass

Can t wait to see the jet boat running!!

This is the best content when you don’t focus on one build and jump around on the work getting done under……. I can’t believe I am gonna say this but Wyatt’s watchful eyes… he has changed soooo much with the move to Florida, back in Colorado he was always obnoxious and loud but holy shit. This man has upped the game for the whole boostedboiz program, Kyle never changes he just wants to go fast. And now he will

The valve pump works pretty good. Just installed on on a 1948 ford f1.

Didn't even know that you two were trying to conceive! Congrats Kyle and Wyatt

That page looks so Fire color matched.

Hyumdai excel pump is the most used for LS setups, you need to just strap or weld on some hold points for the driveshaft on the van, you're fighting the torque so hold is back.

Glad to see you Two wearing seat belts! We kinda wanna see you around for a while!

Kyle and Wyatt y'all rock! Love the channel and content! I'm here for the algorithm! Peace

So many great people in Florida!

I love the Corvette guy can’t wait to see what y’all do with it

Awesome progress guys 🦾

Looks good brother. Can’t wait to see you guys out having fun.

Kyle have you thought about cutting up an old innertube and using it between the mount and the boat? Possibly a little vibration dampening and it will keep the steel and aluminum from touching.

Cayman has always been a favorite of mine since NFSMW 2005. Flat 6's just sound cool too. Always thought it'd be the perfect daily sports car, low but modest HP on a chassis that was built with tracks in mind. They're pretty reliable as far as German cars go too. They all always end up with electronic issues more than anything, but Porsche, Merc, and VW are generally mechanically stout. Rarely ever blow up even if you just do the necessary maintenance. Oil changes in 4000-5000 mile intervals. Little things like spark plugs, filters, etc. Fill up with Shell Premium now and again, run it for at least 1500 miles. Literally cleans the inside of your engine and injectors. Goes a long way with these cars. I've owned Mercs and seen Porsche's with 300k and over, with little ever done to them, no engine swaps, just regular maintenance. They maintain their power well too. Might only see a 10-20 hp drop over that many miles, pretty impressive.

Water to water heatexchanger so you can run it in salt forever. And you could still notch under the the engine mounts and add some thicker material, just make sure its flush.

Getting the Rowdessy running good so Kyle can put a baby seat in back. RECARO makes some. Boosted Baby!

Hoping you read this..,Scatter-shield !!! For the jetboat! That exposed flywheel/driveshaft is a little sketch. I’d also put a carbon steel plate beneath that rotating assembly to keep it from punching a hole in the hull if it comes apart.

Buy a sheet of gasket material and cut out some pieces of it to go between the mounts and the boat. Exited to see this thing ripping!👍

Love the jet boat man!!!!

Gonna lead to a bunch of sick days lol, I definitely have some concerns for those mounts not corrosion, but I feel like the aluminum is going to stress crack. That motor is a 4 banger with it's inherent vibrations I think the aluminum needs to be beefed up for sure

McMaster Carr has rivnuts that you can put in the aluminum, to have some legit threads in that aluminum. Give you something really substantial to mount that engine to. Boat looks SIC though!!

You guys really engineer your projects well. !

Can’t wait to see the truck all done

Way to stay positive Kyle, just in case this thing blows up we have to push it, lol

You guys are Killing It!

Gunna be awesome to see the truck finished as well as the boat

So excited for the boiz :)

Well said at the end Kyle, good work

So awesome!