Wonder if they’ll try running it on diesel, should easily run with that compression

@detaart

Жыл бұрын

They would need to modify the head to fit diesel injectors, somehow fit a pump, and then the rods would probably just bend.

@kordta

Жыл бұрын

Ethanol or methanol mixtures of high octane petrol or something like that. Maybe pure petrol. LPG is an option.

@detaart

Жыл бұрын

@@kordta Would be too high for methanol as well i think. LPG might work, but i doubt the engine would live long.

@TheMrDarius

Жыл бұрын

I wonder running E90 or even some leaded aircraft fuel would suffice

@snap_oversteer

Жыл бұрын

Nitromethane used in RC cars/planes might work, but still it's very high compression.

He’s like Gru in that he’s a good guy, but he’s always cooking up something diabolical to do to ladas. The shop workers are definitely his minions.

@mememan2344

Жыл бұрын

😆

@rm25088

Жыл бұрын

welcome to mother russia

@michaelmays9292

7 ай бұрын

Ace mechanics

@elkvis

28 күн бұрын

The Ladas are his minions LOL

That engine is either going to run really good or it's going to get ugly quick!

@4nz-nl

Жыл бұрын

It'll knock harder than a bailiff

@michaelbryan1878

Жыл бұрын

Big end shells will probably give up

@AndrewAudio

Жыл бұрын

My lawnmower has 250 PSI per piston ( it is an old TurfTiger)

@E01F

Жыл бұрын

@@AndrewAudio that sounds pretty high for a gasoline enginge ... maybe your valves need adjusting?

@AndrewAudio

Жыл бұрын

@E01F nope, I thought of that too. I checked the stats online and they matched.

You guys are gonna need some high octane fuel to combat spark knock. And proper timing. Can’t wait to see this fellas. Then get that engine in something and get that power to the ground. I’ll be on the edge of my seat to see this.

@BlackCatRedScarf

Жыл бұрын

Ethanol is perfect for that.

@chuckfarley5415

Жыл бұрын

@Ti They’ll probably need around 120 octane. This can go very bad, very quickly.

@garmancathotmailcom

Жыл бұрын

Spark knock? Do you mean preignition as it occurs prior to the spark?

@ohyou_6599

Жыл бұрын

i think knocking is the idea, so much knocking that spark plugs wont be necessary.

@EllenN2003

Жыл бұрын

@@ohyou_6599 Diesel it is!

You guys are right in the diesel engine territory with that kind of cylinder pressure. So it would be interesting to see how long the modified gasoline engine would last on diesel fuel with the injectors mounted into the spark plug holes with the machined diesel injector clamps mounted to where the spark plugs should be in just so they stay put and hold the pressure.

@SaraMorgan-ym6ue

6 ай бұрын

how many rings is to many rings you asked well watch and find out🤣

The oil tings is designed to hold oil to evenly lube the cylinder, and remove excess, the lower ring is to scrape oil from the wall, keeping it out of the combustion chamber, the reason the more rings raised compression, is because the rings are higher on the piston.. you could simply add a ring land at the top of the piston, and move the existing rings up, more rings only rob power, more friction! And it takes time to seat the rings to get a good deal!

@drd1449

Жыл бұрын

@Karl with a K definitely not next to nothing. Piston rings cause a significant portion of a whole engine friction.

@zoniyat8519

Жыл бұрын

@Karl with a K karl, i would just like to add that the high performance racing 2 stroke engines mainly use single ring pistons

@Samheraghty-qs7uz

Жыл бұрын

But the two strokes racers aren't diesel either

@zoniyat8519

Жыл бұрын

@@Samheraghty-qs7uz matters notwhat kind of fuel the engine uses-their pistons still have ring(s)

There is a certain pressure threshold before it will behave like a diesel engine. A diesel engine has pressure of 300 - 500 psi. And that engine is producing compression similar to low end of diesel compression.

I love this channel, they love breaking things, pushing the boundaries in the interest of education and simply fun

@user-mp4sw7uc6x

5 ай бұрын

Not so sure all that cylinder pressure wont blow the head off?

yess i love insane compression

I need to see it running already 🤣

@nicolasjuares9414

Жыл бұрын

When this gonna happen?

@off-gridoutbackaustralia

Жыл бұрын

@@nicolasjuares9414 no idea I'm hoping that they do it soon

WTF!!! 20:1 From a Lada engine that's insane congratulations to the team there! 😃that means, they achieved better compression ratio even from the modern (skyactiv) combustion engines of Mazda. Well done guys there! I appreciate your simple and the hardworking way that you all devoted to your projects. Thumbs up from me Garage54!

@paviaaPS3

10 ай бұрын

No my man, you mixed all up and is confusing all the terms! 20:1 is simply a ratio of how many times the compression volume can be inside the cylinder volume(stroke volume + compression volume). It has nothing to do with pressure! But you can say that in order for a diesel engine to run properly, you need at least 18:1 or more than that. Mazda has achieved 14:1 in their diesel engine, but has a hard time to start in winter due to low pressure and therefor low heat. But they managed to sort that out using exhaust and glow plugs. The reason they did the low compression ratio was because it produces less NOx and particulates! The new skyactiv x that runs on gas, has a compression ratio of 16:1. What the actual compression pressure is, I don’t know, but could be in the region of 15-20 bar of pressure. For diesel engines the compression pressure must be between 30 to 50 bar in order for the finely misted diesel fuel to ignite

This is definitely going to be turned into an AC compressor

@TurboVisBits

Жыл бұрын

LOL i wish, you can't pump a fluid with a 4 cycle :D

@zippymcfearson2776

Жыл бұрын

I was thinking it would be a diesel.

@andrewt9204

Жыл бұрын

@@TurboVisBits Well, technically you're pumping air with an engine, which is a fluid but not liquid. And you're not trying to compress liquid on any refrigeration system, just the low temp/low pressure gas into high temp/pressure gas into the condensing coil. But even so, this wouldn't work as there's too much leakage everywhere and you'd just keep loosing refrigerant. Cars still use piston based compressors, and there are piston based compressors for HVAC, however they've fallen way out of favor for scroll and centrifugal the last 20 years.

@ABC363ABC

Жыл бұрын

Only 2 Zylinders

That explains the .030 flycut lol. I was gonna comment on it before but i decided there might be a reason you did it. Now i know.

Wow. Nice Cliffhanger. I'm excited to see the next video. Also. Congrats on nearing 800 Subscribers. Congratulations. You all deserve it.

He reminds me of the EVIL MAD SCIENTIST!!! (But on the good guy side). Truly a man of fine arts. Epic build guys!!!.

As long as narrowing the ring lands don't break that should be awesome for torque even with the added drag.

This should run great as a diesel. Spark Plug holes for the injectors and where the distributor goes for the diesel pump. Glow plugs are optional

@paulg444

Жыл бұрын

i like where you are going with this !!!

@jreererer8490

Жыл бұрын

It will bend the rods instantly. Engine knock is basically how diesel engines work, with that high compression, idk if it will last long even on straight gasoline or LPG

God, I love these guys. They just GO FOR IT. In the name of science :-)

I love these guys ,they are trying literally everything I think about while am working on an engine.

@SaraMorgan-ym6ue

6 ай бұрын

rejoice or are full of regret meh either way is entertaining to watch🤣

using more rings will increase the drag robbing power

Great video guys, thanks for sharing.

Yes! Can't wait to see this engine running!

@nicolasjuares9414

Жыл бұрын

When they go put video bro

wish they would someday combine all power boosting experiments into one vechile. Like what beast it would make with dual engines, shaved crankshafts, dual carbies, extra piston ring... plus whanever else i forgot

@wills.5762

Жыл бұрын

All that, but 2 of the inline 12 they made

need to put that twin carb manifold they made on it.

I built a Honda engine that maxed out a 300 psi gauge in 3 rotations so we had no idea how high it really was, it took a pair of pliers to hit the release valve

The best way to increase dynamic compression is camshaft timing. Advance the cam a bit. Maybe 4 degrees or so, and you'll get more low end grunt. Also, good cylinder head port, and seat work will help. Try a 5 angle valve job, and cut the intake valves and seats to 30 degrees. This will present more open area at the valve curtain at lower lifts, and will enhance low lift flow, improves cylinder scavenging, and will build low end torque

Solid! Top KEK! Peace be with you.

I think I’ve been watching y’all since I was like 13 I’m 21 now and you some how still amaze me with ideas I couldn’t think of

Add a cam with a good amount of valve overlap and alcohol for fuel and that motor should make some impressive power.

@BlackPill-pu4vi

Жыл бұрын

Vlad will have to send the stock Lada cam to Isky Cams in California. They can analyze the stock cam and then make an entirely new custom cam from scratch for this particular Lada engine.

Oh yeah! I'm looking forward to the next phase

TELL ME YOU’RE GOING TO TRY RUNNING IT OFF OF STRAIGHT DIESEL 🙏

@neptarclepuffin

Жыл бұрын

More like staight gasoline lol for a dieseling cycle

@turtlemotonation

Жыл бұрын

@@neptarclepuffin honestly, if they run it purely off compression I’ll be happy 😂

@detaart

Жыл бұрын

@@turtlemotonation ping ping ping kaboom

@centralintelligenceagency9003

Жыл бұрын

@@detaart Knock Knock

@shlushe1050

Жыл бұрын

​@@centralintelligenceagency9003who's there?

Awesome work!!

Good luck with this project💪

I would think the hose should handle the higher compression since the gage goes way past 20 kilopascals. It should be interesting to see it run. 👍

@SaraMorgan-ym6ue

6 ай бұрын

do it buy a card with his autograph get it while supplies last🤣

I been asking for this for 2 years! Finally you're finally doing this..

Love the channel. Awesome experiments

Garage 54 is like a car verzion of mythbusters.

284.6psi for those playing along at home.

@scottvincent7666

Жыл бұрын

Thank you

Thanks!

10/10 need to see it properly tuned on the dyno I’d love to see if it makes power or goes bang

cant wait to see this running 😄

Finally a purpose for that old diesel fuel injector pump you had bolted to that other Lada.

Love your videos!

You guys are up to almost 700k. Subs ! I remember the orig garage humble russian beginning Congratulations 🎊

Gotta try this too

One of three things will happen once the engine starts 1. Head bolts/studs will fail and head will shoot off 2. Main cap bolts/studs will fail and crank will fly out the bottom 3. If they run gasoline as the fuel, the plugs will blow out the head, or there will be a massive predetonation that will destroy the engine

Sounds like some serious boost is going to be achievable with that engine well hopefully & that’s a very nice color combination on the engine

Instead of increasing compression, do 1 forge engine with crazy boost

Now it need dual carburetors good fuel and a car this must be the first garage 54 motor that I seen that could be a N/A race engine

You guys should try running this on a high octane/ top fuel mix

@ashc3765

Жыл бұрын

They will need alcohol for sure

Most diesels I have worked on had about 500 PSI compression pressure. Now that is with one injector out and the fuel line dumping into a jar or jumpered in the case of Detroit. Compression is with the engine running. Don't know how the 285 was attained. A bit high for conventional gasoline technology, but Mazda has an engine running that way, and I believe lean burn.

Wondering with all that decking if they adjusted the valve clearance of it was OK on that engine? Even non interference engines can run close to the pistons. Looking forward to seeing this being converted to a Diesel which I bet is the game but the question will be how well the bottom end will/ would hold up as well as maybe the rods? Have thought of doing this myself on a larger engine doing low power but being able to run on diesel for a generator.

Add some sidedrafts and a hot cam and it'll be a great race engine. Run it on home made alcohol

Maybe it would be wise to back the timing right down on this thing and run 50% gasoline and 50% diesel to begin with. I wonder if the connecting rods are going to hold up. Don't really understand the reason for putting compression rings where the oil ring should be. Hopefully this isn't a problem for lubrication

Chillinder one! Love it 🤣🤣✌️

i lov3 you all stay safe. ty for this happy pic-me-up- love-love.

Run the exhaust into the intake, wrap copper coils arnd exhaust pipe to generate lotts of steam for intake, 300 mpg

Not sure if the connecting rods will be able to survive the extra compression, I have a feeling a piston and/or rod is eventually going to break. Also you must have an oil ring on the pistons, premature wear on the rings and cylinder walls will happen and also more friction and heat will be generated, basically the engine won't last, could even seize.

@samleen

Жыл бұрын

Just throw some 2 cycle oil in the gas lol

@joshmanis9860

Жыл бұрын

@@samleen true lol

@nicolasjuares9414

Жыл бұрын

@@samleen Bad spark then!

They should weld the cam then file and sand it all smooth and see if they can make there own performance cam... They would have to figure out how to harden the lobes perhaps using a stick welder with a really hard rod...

@79huddy

Жыл бұрын

They could spray weld the lobes and have it hard face nitrited they do it to repair cranks and camshafts on heavy industrial engines

Maybe a head without a gasket, use o-rings, something rubbery for water and oil, maybe a copper o-ring, allowing the head To fit deck to deck, maybe use a thermal grease in between, to promote thermal transfer, preventing rust. Maybe deck the block until the piston rings are about 1mm from the deck, then machine a 1 mm pocket into the head, maintaining valve clearance, and quench pads, clearance, are tight, tight enough to prevent carbon buildup. Possibly reach, 250psi compression! And CNC the piston dome to fit the head,

It’s great how you lot keep coming up with new ideas and testing them out so we don’t have too. Have you tried fitting a different head to the larda engine block or fit a larda head to a different engine block. I used to test that when I worked at the scrap yard. I found 3 different engines that you can swap heads and blocks

The main issue I imagine is the total combustion pressure is relative to normal atmospheric pressure, there's probably some sort of a curve that shows the inefficiencies of too-high compression where at some point you're using all the combustion energy just to compress the next shot, and no useful energy comes out of the crankshaft.

@garmancathotmailcom

Жыл бұрын

That's nearly impossible. What do you think the actual pressure of the explosion is?

@dimitar4y

Жыл бұрын

@@garmancathotmailcom you don't know how physics work do you. Good luck magically harnessing all the kinetic energy from a tiny explosion in a tiny chamber where you nearly have no control over combustion timing, and then having it somehow flywheel into another compression.

@nicolasjuares9414

Жыл бұрын

Well see boy well see stfk

@garmancathotmailcom

Жыл бұрын

@@dimitar4y Look in the mirror perhaps? If nothing is absorbing the energy through heat or deformation, it is all harnessed. Generally 1/3 of ICE energy is waste heat.

@finlaymcdiarmid5832

10 ай бұрын

Practical engines have been built with ratios up to 25:1 this is about 20:1. What your saying sounds right but a good few engines have gotten to the same level or not quite alot higher ratios.

if the valves are open at all during any compression what so ever, you have so much that it could be pressurizing the head therefore the crank case. could explain the blow by. different cam and valves shell run mint

I bet that would make some powerful torque

He speaks so calmly idk he just seems a good person overall.. I think i see him as a fatherly figure...

its going to seize, dril someo tiny holes in the lower 2 sets of rings, dress and polish, at least there will be a way to oil the cylinders, for the compression issue you need a jake brake or compression reaslee for each barrel... you open it up then slowly close while cranking over with ignition and fuel on, she'll fire and spin on 12V

This engine could be suited to run on diesel, considering the high compression ratio. But it needs to have its internals strengthened so that it doesn't disintegrate after a short while

@garage54190

Жыл бұрын

Inbox me for more information 👆👆......

I wish I lived nearby these guys so I could see all the experiments in person

That engine will run nicely on Ethanol or Methanol.

An idea I just had: What would happen if you put like 3 or 4 brake calipers on each brake disk on a car? Would the brakes be extremely twitchy or what would happen? Could you lock up the tires at 50km/h?

@02invader18

Жыл бұрын

Да заблокируется

Should be fun seeing whether this engine can survive such high compression or not... :P

gotta appreciate the russian stereotype of always wearing a tracksuit and buddy puts on his fancy tracksuit for this vid love the videos just poking the russian bear

Using total seal piston rings will achieve the same result, but without the additional friction extra rings will cause.

@DarkLinkAD

Жыл бұрын

Says the marketing. Lotta people having issues with those in the real world.

@andreastheile426

Жыл бұрын

How do you Mount them

@TurboVisBits

Жыл бұрын

@@DarkLinkAD they work fine for non dry sump applications.. lots of goofy scenario... gas ports on stock cams cause problems, vac pumps cause problems... shrug.

@eweunkettles8207

Жыл бұрын

russian rings are far superior to american gimmicks .

@eweunkettles8207

Жыл бұрын

​@@andreastheile426 just like american girls

As Rob Ferreira said, try running it on diesel. Your 20 bar compression rate should ignite the diesel with no issue!

alcohol theoretically supports compression ratios of 16/1, the ignition timing should have almost no advance, I would do it like this

You can run with this much compression, it takes 130 octane leaded aircraft fuel, and a retarding of the ignition timing, but, it is feasible. I seen my cousin run an Oldsmobile 5.7 liter diesel this way, back thirty five years ago. That little engine was a torque monster

Rip block LOL 😂😂😂 valve springs chain tensioners lol 🤣 God im praying 🙏

for those wondering that is about 19.5:1 compression

Don't forget about intake valve timing to create an Atkinson cycle engine that would reduce max psi hybrids use it for efficiency,

Screw rebuilds, imma just machine my pistons to fit 6 rings 🤣

Ah yes the industry standard unit for pressure -kilos!

I figured the starter or ring gear would give up or both at the sametime.

I had a opel gt with 18 kilos and i had to run 105 fuel and two cans of Is octane boost just stop the spark Knock. The car ran great 0 two sixty in 3 seconds top speed at 185mph.

C'mon guys 😁 Start this papi asap! 😂👍

I have a question. Did you put an adjustable camshaft sprocket on the camshaft? Taking that much material off the block and head will change the valave timing......

Is this going onto the drift bus? That might work great!It's been a while since last time we saw the cool BUS on the channel

move the crankshaft from the centerline to the side by 10mm. and test it on dyno will it make more power !!!

Hell yeah!!!

Please get a base line on a dino or a tuner program. Also with that many rings I’d let it idle for awhile or go around the block a couple times not to exceed 2000rpm and do an oil change.

I know that you guys are very good with what you do i saw your two cylinder now that could have probably used that compression to run but why would you want such high compression on a small engine and you can probably get good fuel in some places but still the bottom end is stock am I correct?

6 rings per piston 🤯

Does the engine have an adjustable cam sprocket? Trimming that much off the block and head will probably knock cam timing off a couple degrees as the cam/crank distance has decreased.

31 million dollar American drone - just bump it. ***Crash***. 😂 😂 ❤

Love this guy!! 😀

I wish this engine the best but if I were a betting man I’d say it’s gonna have a short life 😂

youre gonna need some high octane fuel lol curious to see how this turns out if you use pump gas... lots of detonation I'd guess. As for extra rings im of the belief they dont really make a difference at higher rpm. at cranking speed they do but once your at running speed and especially into the powerband I dont think they help.

275 psi wow!

Imagine strapping a turbo to this thing with 285 PSI already getting in!!!

@finlaymcdiarmid5832

10 ай бұрын

Thats called a bomb my friend..

So what is it 19-1 compression ratio? You may consider Propane / Natural gas if you run into knock issues. Just a regulator and valve should work.

Did you have to shorten the head bolts just Incase they bottom out before the head gasket is fully compressed ???