CR Tdi injector adaptation
Автокөліктер мен көлік құралдары
After changing injectors or in our case putting in another engine that came with injectors you have to adapt your computer to match your injectors. Learn how to avoid mistakes in this process in this video. This was on a 2014 Jetta tdi, but it applies to any Tdi 09 and up.
If you learned something or these videos helped you fix your car please consider donating to the continued production of these video's by finding the donate icon on my website at www.kansascitytdi.com
Help me get approved as Amazon affiliate by making any purchase through my amazon affiliate link -------- amzn.to/3s2SB6E
Just search for anything you might buy normally, and the purchase will help me get approved as a Amazon affiliate.
Please do not call me for tech help. Feel free to post questions in the comments below. I try to answer every comment if I have something helpful.
Пікірлер: 32
VERY helpful thanks a lot M
@CoolAirVw
8 ай бұрын
thanks
thanks very good info
@CoolAirVw
Жыл бұрын
thanks for watching and commenting on my channel.
Hi good afternoon, I am about to buy from Darkside 4 new Bosch injectors for my golf TDI MK7 TDI with a CRUA engine. I would like to know if after replacing them, I will need to complete this process of adaptation? because they also have for sale this software.
So there are no aftermarket injectors available since they would have to be calibrated to match the flow rates designated by vw serialization per some unknown on each & every comon rail piezo injector?
@CoolAirVw
Ай бұрын
thats a logical conclusion but I would guess someone is doing it. But software would be better way to make more HP.;
Hey coolair. I replaced the maf on my alh tdi as preventative maintenance, felt way better had a lot more power it felt great for a couple weeks. Now i am having boost issues and it's not boosting as much. I have the code p0101 now. I unplugged the maf connector and it only has 4 pins. I am very confused. Because my actual maf has 5 pins but the connection only has 4 wires going to it and 4 pins. It has the slot for the 5th pin though. I have a picture of the connection if that would help
@CoolAirVw
Жыл бұрын
Put the old one back in. Sorry I dont have the number of pins on every component memorized. From memory I think only 3 pins are used. Look up a wire schematic. Other Vw's use 5 pins on Maf because they have a built in air temp sensor but the air temp sensor is on the Map sensor on your car, so I believe it works with three.
After the injectors adaptation is it necessary to do injector quontity adaptation.? Thanks for your answer.
@CoolAirVw
9 ай бұрын
no
i dont have this engine but just curious., each injector has its own chip that the ECU talks to and they are serialized with this 7 alphanumeric ID ? Thanks!
@CoolAirVw
Жыл бұрын
no. its a calibration.
Hi.I have a passat b6 cbab,I have 2 errors,p1065 and p0088 high fuel pressure.What could be? The car gets sometime limp,but it can be 2 weeks with no limp and then came again.The car has no fluctuation,it works well,the turbo come on 2500 rpm not on 1800-2000.Could be the return rail? Sometimes starts a liitle bit slow
@CoolAirVw
Жыл бұрын
Dont know off hand. Your probably gonna need to get it to shop that can diagnose it.
Have open circuit on all injectors any one know what resistance should be on the 2.0tdi 2012 passat cffb
How do these later diesels stack up to the earlier ALH?
@CoolAirVw
Жыл бұрын
I'm not a fan. If it were legal to delete I might like them better.
Do you need the latest VW ECU software update for this to work? As you maybe putting 2023 latest injectors into a VW with 2010 ECU software, so new injector coding may not be recognised ? Has anyone reading this come across this problem?
@CoolAirVw
Жыл бұрын
I have not run into this.
@TheCerovec
10 ай бұрын
It shouldn't happen if it's the same type of injector with the code of same lenght. Injector coding is just a calibration values but written in a code. Your injector offset, pre injection,full load, etc. So it has nothing to do with the age of your car or the injector. The only reason i can think of is why your ecu wouldn't accept the injector code is that some of the values are outside maximum or minimum values. You can search for IMA decoder. Decode the values and then compare them to min/max values that are allowed for your engine,if you can find them.
At least you didn't say "ADAPTION"....on another video, the guy kept saying the right term, but wrong haha. Nor do you call a nut a bolt, or a bolt, a screw! uhh one of my pet peeves. And I agree: ALHs just simply seem much simpler.
@CoolAirVw
Жыл бұрын
Yeah, that stuff annoys me also.
@davidparker9676
Жыл бұрын
I worked with a guy that called screws nails and nails screws..... I really don't miss him... at all.
Bonjour mon ami J'ai besoin de votre aide Voilà suite a une fausse manipulation dans la centrale électrique (09) Dans l adaptation Le verrouillage centralisé Avec la clé ne fonctionne plus C'est une léon Seat 2012 Pourriez vous me donner un tuto ou une solution Avec mes remerciements anticipés
@CoolAirVw
Жыл бұрын
Je n'ai aucune expérience avec cette voiture. Pardon.
@amichemourad2574
Жыл бұрын
@@CoolAirVw Merci pour votre retour Et belle journée
Hi my injection quantity is bouncing around 1.5 and 2.2 mg it supposed to be around 3.0 to 9.0 mg what could be problem all 4 injectors are within range car is audi a4 2.0 tdi 2006 thanks
@CoolAirVw
Жыл бұрын
Dont ask the same question on multiple videos.
@abdulbeany1894
Жыл бұрын
@@CoolAirVw why not trying to get advice from whoever can help me
We all call it coding....
@CoolAirVw
Жыл бұрын
Its hard to stop. Plus sometimes we say adaptation when its basic settings. oh well.