Since I had to re-upload this vid, I went ahead and remastered the audio too!

Thanks so much for all these videos Randy. It's given me a lot of confidence in doing things I otherwise wouldn't try. As you say in this video, sometimes you just got to wiggle it a little bit.

re-install tip Put HPFP in freezer / cold temp for 15 min , ez insert !

@FiveFiveGarage

5 жыл бұрын

I never thought of that! LOL Good tip!

@oliverromero6633

2 жыл бұрын

wich part of the hpfp

Hey Randy, great vid as always, keep up the good work. You're one of the few MS3 channels out there that is top notch. Don't ever give up!

@FiveFiveGarage

5 жыл бұрын

Thanks!

@sq33qs

4 жыл бұрын

@@FiveFiveGarage - Almost a year later but i finally got my HPFP internals, autotech but i'm sure 95% of the install info i need will be on this video(just coz different internals). So thank you again. :)

@FiveFiveGarage

4 жыл бұрын

The process is pretty much same, I am going to pull my pump off again and take a look inside, it shouldn't need a cleaning but I am curious.

@sq33qs

4 жыл бұрын

@@FiveFiveGarage - My pump was grimey but then again, it hadn't been opened before so that is expected, cleaned mine as best i could and now after the install my pressure is way up on avg vs the stock internals.

@FiveFiveGarage

4 жыл бұрын

Great to hear! Err...read LOL

protip- if pressure in fuel line, pull fuel pump relay from fusebox and start car, let run till it dies (will take longer than you think) but it will significantly reduce the size of mess though there will still be some pressure and fuel in the line, it wont be NEAR as bad. (tip w/i a tip.. pre-clench butt cheeks! as someone whos done many MANY BG A/F cleanings on these engines, its still a surprise as to when the line will "pop" off)

@FiveFiveGarage

4 жыл бұрын

Good looking out on this one!

Great stuff Randy!

If your car is not newer, or is from up north I would recommend using PB Blaster, Kroil, or Seafoam Deep creep on the threads for the fuel line at least a day before you do this, and then using Line Wrenches and not open end wrenches. You can get a set of line wrenches from Harbor freight for like 20$ and its still gonna have more grip, and less chance of rounding off these fuel lines than a Snapon Flank Drive+ Open end. Ask me how I know.

@FiveFiveGarage

3 жыл бұрын

I have used so much PB Blaster I am thinking of investing in the company!

@EvlEgle

3 жыл бұрын

@@FiveFiveGarage cant go wrong there. When i was still wrenching for a living id go through a can a week easy.

The fuel pump internals + spring were stuck in the sleeve on mine, so I had to get a tap and hit it a few times on the opposite end to pull the hat/retainer and spring out.

Great step by step. Now….ineed to learn exactly what the hpfp does.

@FiveFiveGarage

10 ай бұрын

It takes base 40psi fuel pump pressure and increases it to over 1600 psi for direct injection.

Now you said tap the tappet down flush when putting the hpfp together but it doesn't go flush it just seats down far enough over the pinrod for it not to come off. It still can be moved and wiggled but won't come off. I just did this installation yesterday. So am I wrong? Should it be flushed and the tappet not move at all? Thank you for this video.

@FiveFiveGarage

4 жыл бұрын

When you use the installation tool, the tappet needs to be flush in the tool for it to be installed properly. It sounds like you got it on there correctly, if not the tappet would come off.

Thanks this is where im at

I’m smelling Fuel, after installing my fuel pump internals. Whats the most common reason? Im guessing a leak, but where exactly would the leak be at?

@FiveFiveGarage

Жыл бұрын

Check your lines. Check the hard line and make sure it doesnt have a crack in it, it can happen. I ended up replacing mine with a braided PTFE line.

Would i need a tune right after installing the new corksport hpfp, on top of having a turboback exhaust(also from corksport)??.

@FiveFiveGarage

4 жыл бұрын

Yes. Stock map is not going to be able to keep up with the improved airflow with the turbo back exhaust, even with upgraded HPFP. Get a tune, you will be able to take advantage of that increased exhaust flow since the stock downpipe restriction is gone (faster spool up, turbo becomes more responsive, more boost)!

@Kcdoesasmr

4 жыл бұрын

@@FiveFiveGarage thanks!

Nice video. Question, what does this do? I have a 2012 ms3 and thibking of doing this..im buying a cobb downpipe and accessport next week

@FiveFiveGarage

4 жыл бұрын

If you are going to add a downpipe you need to do fuel pump internals FIRST. What these do is allow the high pressure fuel pump to supply enough fuel to support mods. If you add a downpipe without them, the engine will run lean, and lean under boost = blown motor. HPFP internals is always the first recommended mod because of this. It will enable you to safely add and support bolt-ons all they way up to ~ 380 - 400-ish HP.

Great work!

Would i need a tune after installing just a hpfp?

@FiveFiveGarage

3 жыл бұрын

No you don't need a tune after installing this.

Hey, I was wondering if I would need a tune after an air intake, Corksport cat back exhaust and CS hpfp

@FiveFiveGarage

3 жыл бұрын

Which air intake? If you are using a larger than stock (I am talking 3" or more) MAF? Yes. If not, No. HPFP doesn't need a tune. Cat-back doesn't need a tune.

@yavzeab9584

3 жыл бұрын

It’s a JBR short ram

Was wondering what the extra fuel was for? Great video, I'm ready to do it

@FiveFiveGarage

4 жыл бұрын

Why the upgrade? The stock HPFP can't keep up when you add mods and turn up the boost. If you are going to add performance parts, this is the #1 must do mod to keep from blowing the engine.

@markjoosten3693

4 жыл бұрын

No the extra fuel you had in the cap, I read corksport instructions (briefly) and watched ur video, didnt see you use the extra fuel in the cap, was wondering what is was for. Haven't bought the internals yet

@FiveFiveGarage

4 жыл бұрын

Ahh I got what you mean now! That was from when I opened the pump and the excess fuel came out and I had that there in case I needed to prime the pump. You won't need it. I had to go back and rewatch the video to see what you meant 😂

Is there a replacement piece on that installation tool with the grove

@FiveFiveGarage

2 жыл бұрын

Not that I am aware of. I got everything as a kit from Corksport.

Quick question if you know, would I need a tune if my only mods were hpfp, rece pipe (2nd cat delete) and cat back exhaust? Thanks!

@FiveFiveGarage

3 жыл бұрын

No, you wont need a tune for those.

Why do you want to not move the 17mm bolt, my 19 mm one is just rounding

@FiveFiveGarage

2 жыл бұрын

Its easier to apply torque on the larger nut. I didn't want to round off the 17mm because that would require fuel line replacement. If you are rounding that 19 mm, try a flare wrench.

I just did this process, after doing so my car fuel idle between 100-300 , And running real Rich , What can I do next ?

@FiveFiveGarage

3 жыл бұрын

Recheck all your connections, and make sure that all of your intake clamps are tight. Make sure the MAF is connected snugly.

My passengers engine mount just blow today. Very nasty. You should do it next

@FiveFiveGarage

5 жыл бұрын

Did it get everywhere? I am thinking about the Damond Motorsports mounts as a project next spring.

@fearandsmoking

5 жыл бұрын

I'm changing mine ASAP! Mine is collapsed but not completely done yet!!!

I just got mine install with the accessport i install the stage 1 sf map what afr do i suppose to have lol tbh i think i feel it less torque how do i know if the its receving enough fuel and its safe

@FiveFiveGarage

2 жыл бұрын

On your accessport, add the gauge for HPFP activation pressure. Go for a drive, when you get into boost it should go over 1600 psi. If it does your good. Your AFR should dip into 11s -12s in boost, 14.7 @ idle, and 15s in cruise situations. If you get into boost and your AFR is higher than 14 you have a boost leak somewhere and the car is leaning out.

Did this mod made your car run rich in fuel? What was the long term and short term fuel trim after the installation?

@FiveFiveGarage

3 жыл бұрын

No, the car didn't run rich after installation. As for the fuel trims, I can't tell you what they were then as the car was bone stock when I did this mod but LTFT should be in the 7-10 range for a stock car with HPFP after installation. If you have an intake or other air flow modifications it will vary as well.

I just bought one i need to know if mine has this ...... i only have intake and bov

@FiveFiveGarage

4 жыл бұрын

Do it come with an Accessport? If it did you can check HPFP activation pressure and if it is over 1600 psi in boost, then it has upgraded internals. There really isn't a way to tell other than opening the pump. If you are going to mod your car further, I highly recommend you go ahead and upgrade the fuel pump internals.

Do you guys think that installing these upgraded internals is worth it on a MS3 with 160K miles already? All I have right now it’s a K&N short ram intake. Will pushing the engine even harder just not worth it?

@FiveFiveGarage

2 жыл бұрын

Replace them. Chances are the rubber seals in the pump are in need of replacement so might as well.

I imagine I did something wrong if my check engine light came on. Any suggestions? First mod install.

@FiveFiveGarage

3 жыл бұрын

Do you have a code scanner? That will let you know what caused the CEL. Double check everything you did and make sure your couplers on the intake are tight. Might be a boost leak.

before starting the car did you prime the fuel pump at all?

@FiveFiveGarage

4 жыл бұрын

I let the pump cycle a few times (turning the ignition on and off a couple times without starting) to get some fuel to the pump, it then started right up.

Noob here could I add a fuel pump in line and remove the HPFP I am going E85.

@FiveFiveGarage

4 жыл бұрын

No. You need the HPFP, since these cars are direct injected. Inline pump won't be able to raise fuel pressure to the 1600+ psi needed for DI. If you are going E85, I would recommend deciding if you are gonna run an E30 tune. Straight E85 is bad for the HPFP in these cars, Google for "black death" and Mazdaspeed 3 for more info.

Do you have to tune it when installing this

@FiveFiveGarage

3 жыл бұрын

No, HPFP doesn't require a tune

U need a tune for this?

@FiveFiveGarage

2 жыл бұрын

No tune needed for HPFP internals.

👍🏽👍🏽

The tappet is not attaching to the shaft. Followed your video and instructions, but it's not working.

@FiveFiveGarage

3 жыл бұрын

It takes a couple taps and a bit of force but it will go on.

@pocketaas75

3 жыл бұрын

@@FiveFiveGarage it's assembled after about an hour. Not sure what was wrong.

@pocketaas75

3 жыл бұрын

You mentioned your pressures were at 1600 psi. Did it run the same before you swapped the internals? Just curious as it was mentioned to me that I would need a tune for this upgrade.

@FiveFiveGarage

3 жыл бұрын

Before I swapped internals my peak pressure was around 1450 psi. Now I can see them as high as 1900 psi. You do not need a tune for HPFP Internals. The pump is mechanical, the ECU does not control it.

@pocketaas75

3 жыл бұрын

@@FiveFiveGarage thanks for the replies back. You're big help!

As always, great video. How much for the kit?

@FiveFiveGarage

5 жыл бұрын

$349.99

@craigzilla100

5 жыл бұрын

@@FiveFiveGarage wow!. Thanks

😭 the torx screw is almost rounded and i cant get it off

@FiveFiveGarage

5 жыл бұрын

Be very careful. You may have to use an e-z out 😨

You already had mods on your car before you installed hpfp internals ?? Weren’t you worried about running lean and going boom?

@FiveFiveGarage

5 жыл бұрын

This video was actually the 2nd video I did after I got the accessport, but do to some audio issues, I had to re-upload it. Thanks for reminding me that I probably need to put this in the right order in the playlist!

@anonguy6453

5 жыл бұрын

Generally you can run bolt ons like exhaust (minus downpipe) and full turbo inlet before needing to do fuel pump internals. My car has been this way for months and I haven't had any problems to date. In any case I plan to do an etune within the coming months with or without hpfp internals and a downpipe. Better safe than sorry.

@FiveFiveGarage

5 жыл бұрын

@@anonguy6453 It depends on the generation. Gen 1's can get away with a couple mods, Gen 2's will start to run lean. After seeing so many of these cars run into issues of going lean and ZZB, I recommend to anyone starting with the fuel pump internals first. Unless you have an accessport or a wideband installed in the car, you can't see the AFR's and there is no warning light on the dash. Its better to be safe than sorry as DISI motors aren't cheap to replace.

Well... its a E-Torx... External Torx.