Convert
Ғылым және технология
Hello friends, today in this video I have shown you
how to make a 220v AC to 3v-6v-9v-12v-24v-36v
-48v-60v-98v-110v-120v.DC driver circuit,
How to make 220v to 1.5v-3v-6v-9v-12v-15v-24v multi output converter,
Convert #220v ac to 3v,6v,9v,12v,24v,36v,48v,60v,98v,110v,120v,150v DC Led driver,
DC converter without transformer Please note, this circuit is not isolated from mains so don’t touch any open wire in this circuit when the circuit is plugged in.
If you want to increase the brightness of the led use 10W led and 47uf ceramic capacitor in place of 5uf. This capacitor must be rated 400v or above.
Thank you very much for watching
Have a great day ❣️
Friends if the video is really helpful please Like Share 🙏 please don't forget to Subscribe the channel.
Thank You...
*************Ultimate Electronics*************
Пікірлер: 114
Greetings from Bahía Blanca, Argentina. Very good, GO LIKE
@UltimateElectronics
6 ай бұрын
Thank you sir
Good,,, وضح ارقام العناصر،،zooom pacather😉🙋
@UltimateElectronics
10 күн бұрын
Thanks for watching sir
@user-di2mf2fn7n
9 күн бұрын
High-heeled_convertar D. C, to A. C 😯
mantap bro, saya sudah buat 1perangkat dari mesin tv bekas voltage 0 - 125 volt
@UltimateElectronics
7 ай бұрын
Very 👍 good job
excelente seus vídeo gostei muito valeu
@UltimateElectronics
7 ай бұрын
Thank you sir 🙏 also thanks for visit our channel have a great day
Buen día gracias por el aporte saludos
@UltimateElectronics
2 ай бұрын
Thanks for watching
Rangkain yg sangat indah dan menarik . Mohon di tuliskan di kolom diskripsi komponennya .sukses selalu .trims
@UltimateElectronics
6 ай бұрын
Thank you sir
This circuit is very clear but it is so dangerous and then it can't be use for a long time.
@UltimateElectronics
4 ай бұрын
Thanks for watching sir ! Yes sir you are right please do this with proper safety thank you again.
In the block diagram 100 ohms Registance has been shown connected before the 15uf capicitor but while making the circuit 100 ohms Registance has been shown connected after the 15uf capicitor. Please clearify the correct connection Anil Kumar Goel
@UltimateElectronics
7 ай бұрын
Sir please see the full video you will understand everything thank for great feedback 🙏
obrigado amigo bom vídeo valeu
@UltimateElectronics
7 ай бұрын
Thanks for your great comment sir
What is the Ampere out put at DC voltage? You should have included an Indicator at both yhe Ac and Dc ends.
@UltimateElectronics
7 ай бұрын
Thank you sir 🙏 for visit
@oimoicuocsong-mcs6108
6 ай бұрын
A 100 ohm/1 watt resistor can only operate at a maximum of 0.1 amp. So the maximum LED current is 0.1 amp.
Nice and easy prj but a question..... in to video you write 2 x 150 k ohm but yellow purple yellow it s 470k not 150k........what kind of resistor i can put? thx a lot for help
@UltimateElectronics
4 ай бұрын
Yes this is a typing mistake thanks for watching
Super video also very useful 👌
@UltimateElectronics
7 ай бұрын
Thanks a lot
I have plan to use 160 LED RGB light convectively ,is this Circuit support..??
@UltimateElectronics
7 ай бұрын
Parallel or series
Nice
@UltimateElectronics
7 ай бұрын
Thank you sir
We can make this circuit by using only one pf and one Registance and same result can be achieved. Why another pf and resistance has been used on a 220 ac supply line. Anil Kumar Goel
@UltimateElectronics
7 ай бұрын
Sir there are different ways to make this circuit like this❤️
Necessito alimentar uma bobine que funciona a 60VDC, posso utilizar este esquema para alimentar essa bobine? Obrigado
@UltimateElectronics
Ай бұрын
At first thanks for watching . Sir the circuit is not isolated so please only use this circuit only to glow led light.
Devre basit ama çok iş görür
@UltimateElectronics
2 ай бұрын
Thanks for watching sir
Salve, bello il circuido posso collegare anche un voltometro e amperometro come grazie
@domenicodimatola7102
5 ай бұрын
Puoi mettere anche il valore delle resistenze
@UltimateElectronics
5 ай бұрын
Thanks for watching sir
debería medir con un voltímetro para verificar la caída de voltaje
@UltimateElectronics
6 ай бұрын
Thank you sir
We see a lot of dc voltages here. How can you explain that? The dc voltage gets enough according to the load?
@UltimateElectronics
5 ай бұрын
Due to low amps like 300 to 500mA the circuit is able to operate all the led like 1.5v to 120v
How it can output variable voltage level
@UltimateElectronics
6 ай бұрын
Sir there are few amps generated in the output section
Peace be upon you. If you would like a video about installing lighting for an object that moves around itself, such as a chandelier
@UltimateElectronics
7 ай бұрын
Ok sir I will try or my best please keep watching
the colour code of the resistors read yellow violet yellow ie 470k your video mentions 150 k . Confusing.
@UltimateElectronics
7 ай бұрын
You can use 150k
👍👍👍💡💡☕☕
@UltimateElectronics
7 ай бұрын
Thanks
Boa noite Moro no Rio de Janeiro Brasil e aqui a tensão de entrada da rede é 127 volts. Posso usar este circuito?
@UltimateElectronics
22 күн бұрын
Sir thanks for watching also thanks for your valuable comments, sir at first you need to know how is the purpose to use the circuit. This Circuit is not isolated and only it is used to glow led bulbs or lights,
@LEALZINHO660
20 күн бұрын
@@UltimateElectronics Sim eu quero usar para acender leds.
Can i use this diagram for my 60v amplifier?
@UltimateElectronics
4 ай бұрын
No sir it is only used as a led driver or up to 4v lead acid battery charger
@dr.black.2295
4 ай бұрын
@@UltimateElectronics so sir how to use my amplifier without any transformer and power Supplys......I'm from Bangladesh....i Don't have money to but 60v transformer/power supply......i want to use direct ac volt in my 60v transformer....tell me how?
sir fire alarm with relay i can use this 12v ac to dc driver circuit?? reply me sir🙏🙏🙏
@Megharaj_metrani
7 ай бұрын
sir pls reply me🙏🙏🙏
@UltimateElectronics
7 ай бұрын
Bro this circuit is not isolated and there are some electrical hazards so please don't connect to the fire alarm if you connect then please cover it be careful and a zener 9v -12v connects to the in between Capacitor thank you
@Nooman62
7 ай бұрын
kzread.info/dash/bejne/ZIR4lrirpcfKfJs.htmlsi=9oDWhc89E1TMbmmn
@paulovoador10
6 ай бұрын
Como converter para 110 v ?
@Nooman62
6 ай бұрын
Es lo mismo desde la bobina del relé protegida por la resistencia.
هل استطيع استخدامها tester leds
@UltimateElectronics
6 ай бұрын
Yes you can but be careful there are some electrical hazards don't touch anything during check
Volt nehi watts batiye kite kitne watts tak Led use karsakte.
@UltimateElectronics
Ай бұрын
Upto 18-25w thanks for watching
I don't think that it can supply that much current to regulate by the regulator bridge. The two main capacitors can not deliver even 1A. Even small bridge or four small rectifiers can do the job.
@UltimateElectronics
7 ай бұрын
Yes sir it can
@oimoicuocsong-mcs6108
6 ай бұрын
A 100 ohm/1 watt resistor can only operate at a maximum of 0.1 amp. So the maximum LED current is 0.1 amp.
Hola los resistores son de 470k
@UltimateElectronics
7 ай бұрын
Sir You can use this one
Kia is sy 3hp solar motar chaly ga 110v dc hy
@UltimateElectronics
6 ай бұрын
Sir is keliye vi 220v to 110v ac to ac converter bana dunga thanks for watching
Sir ji pf ki kya velue hai ...Kuch bata nhi sake to Hme kese pata chalega sry .Smj nhi aya ..Bol K batao
@UltimateElectronics
7 ай бұрын
450v 105j
@UltimateElectronics
7 ай бұрын
Polyester capacitor
@omprakashupadhyay1461
7 ай бұрын
@@UltimateElectronics Ha vo hi kitni velue ...Sb ki batao
Apa bisa buat cas aki
@UltimateElectronics
4 ай бұрын
You can charge 3.7v/4v Li-ion or Lead acid batteries but not charge high amps due to low amps of this circuit , Thanks for watching Sir
❤❤❤Ok
@UltimateElectronics
7 ай бұрын
Thank you sir
1960 style
@UltimateElectronics
4 ай бұрын
Thanks for watching sir
Что это за понты. два кондёра по 1 мкФ .? Как ни крути, а они включены последовательно, а значит ёмкость в два раза ниже. Можно один поставить на 0,5 мкФ и делов. а это классическая схема драйвера . Да ещё мост выпрямительный такой мощный для лэд не нужен.
@UltimateElectronics
7 ай бұрын
Thank for great ideas
But no amphere and watt
@UltimateElectronics
7 ай бұрын
Upto 18 watts
you are showing 470k and then calling it as 150k
@UltimateElectronics
7 ай бұрын
Video me dekhiye
@UltimateElectronics
7 ай бұрын
You can use any one of both
@miroslavbeno8584
5 ай бұрын
Na videu je : 105 J . Rezistor 150k 2x ahoj
It's 470K resistor not 150k yellow purple yellow= 470000 ohm
@UltimateElectronics
5 ай бұрын
Thank for watching sir you can use 150k also
You are showing 470k
@UltimateElectronics
6 ай бұрын
Thanks for watching
Ca se zerou
@UltimateElectronics
5 ай бұрын
Thanks for watching sir
just led minimum ampere 😛😛😛
@UltimateElectronics
5 ай бұрын
Thanks for watching
150 k resiztor diyorsun 470 k kullanıyorsun yani işi bilmediğin, direnç renk kodlarını bilmediğin ortada daha 12. saniyede izlemeyi bıraktım.
@UltimateElectronics
6 ай бұрын
This is 150k
⚠️💀⚠️☠️⚠️😡😡
@UltimateElectronics
4 ай бұрын
Thanks For Watching sir
Feku chand video 0000.1 mark
@UltimateElectronics
5 ай бұрын
Thank for watching
@UltimateElectronics
5 ай бұрын
This really works sir
👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎
@UltimateElectronics
Ай бұрын
Thanks for watching sir
@user-or7ik2tu6u
Ай бұрын
Что это
I have collected a copy! -- 2 capacitors 450v - 105, 150k between them to discharge these capacitances,I put them on a diode bridge change, supplied 220 volts from the other ends, put a barrel capacitor 450volt 12mkf from the diode constant to plus and minus, 150k between it for discharge, then put a load current resistance of 100 ohms to the plus of the diode bridge and I connected the LEDs - they just blew up! I looked at the output voltage -- 440 volts constant! YOUR SCHEME IS INITIALLY DIFFERENT FROM YOUR OWN ASSEMBLY! NOW ANSWER ME -- EITHER YOU'RE LYING OR WHAT DID I DO WRONG? LOOK AT YOUR DIAGRAM! -- IT HAS A RESISTANCE OF 100 OHMS TO THE CAPACITOR!What if I had connected to the digital probe? -- he would have burned down!
@UltimateElectronics
7 ай бұрын
It is working sir just like universal output