Configuring VoIP Phones in Cisco Packet Tracer
Do you want to know how to configure VoIP (Voice over IP) phone systems? Have you always wondered how to configure Telephony Services on a router to run VoIP on your networks? Have you wondered how to configure DHCP for your VoIP network?
Take my Cisco CCNA iOS Administration Labs Course for $10.00
www.udemy.com/cisco-ccna-rs-2...
Take my Subnetting - Become a subnet master Course for $10.00 (Best selling online subnetting course)
www.udemy.com/subnetting-beco...
DONT FORGET TO SUBSCRIBE AND LIKE THIS VIDEO!
LIKE US ON FACEBOOK:
/ learntechtraining
For more Courses visit www.learntechtraining.com
Buy the Cisco CCNA RS Complete Study Guide Here: goo.gl/8SpGcN
Buy the Cisco CCNA Voice Study Guide Here:
goo.gl/uy6qoU
Пікірлер: 327
I spent an hour on this lab until I came to your video which helped me figure it out in 8 minutes. The lab had the wrong source IP when configuring telephony on the router. SMDH! I was using the data vlan DFG. Thanks a bunch! Great video!!!
Great Job! Thank you for taking the time to make this lesson. I didn't mind the speed as I am able to pause the video and I appreciate you keeping the lessons lean and concise.
Straightforward and informative. I like it was complete and short.
thanks, I searched a lot, finally got what i need! Thank you for this video (Y)
So you were tabbing instead of entering in the command line parts for excluded address and encapsulation i feel so silly haha, very good video!!! thanks so much for helping not only me but my whole classroom to understand better the class of networks and computers :) You are so fast programming!!! good ability i hope i get like that one day, good vibes
It's really amazing and easiest way to get knowledge. For VOICE VLAN. Thanks a lot...
Very good tutorial. Thanks LearnTech. I subscribed to your channel in under three minutes.
This page is an absolute gold mine
multumim Ana Han! You the best! - From C3buc with love
Great session and .........speed doesn't matter. I think you saved my time also. Somebody may take 20-40 minutes(i have no doubt at capabilities of others too, it's the way of teaching) to explain in "SLOW" mode but you explained everything very nicely and smoothly. Thank you.
Huge thanks for this! I wasn't understanding the class I had too clearly but with your example it's making a lot more sense :D
Just completed the lab - thank you very much speed was fine for me
You have earned my subscription with this one bro. Many thanks !
Thank you for another great video. God bless and good luck, Mike
FYI, when using Packet Tracer, if you hold the control key down when selecting the straight through cable, you will not have to re-select it each time you make a connection.
@rulaneshedo2775
3 жыл бұрын
thanks a lot
@Drink_the_cool-aid
Жыл бұрын
Even 5 years later, this comment comes in handy.
This makes everything look pretty simple and easy to understand
Thanks for the video.. the command line or terminal works best for me for sure. Easy to track the moment you get to know the structure.
excellent video, easy and quick to learn :D
Absolutely amazing video. Thank you. Just incase someone is trying out the video in packet tracer and wonder why it is promoting them to configure the MAC address, I learnt from a few people in the comments section that we simply have to plug out the power supply to the phone and plug them in again. Do this twice and wait for the phone to be registered. Repeat the same procedure for the other ip phones after typing the button 1:n command. Great video! 👏🏾
@fredrickmumba8825
4 жыл бұрын
Where n is a number of the phone. If you have three phones like in the video then n can be 1,2 or 3.
@syronmacasadia6405
5 ай бұрын
this saves me haha.. ive been struggling to find the solution for that configure the ephone MAc address thanks a lot
Thanks a lot for this video.It's very helpull for me. Thx again
Thank you for the lesson, it was clear and brief, and to the people who complain about the pace, first its a video so you can rewind on the part you miss, plus you should have some basic knowledge on both R&S and voip before executing such labs. Good luck all
@LearnTechTraining
4 жыл бұрын
Thank you so much for the wonderful comment! I don’t take negative feedback any less than the goods after teaching as long as I have been ive learned that everyone learns differently. Hopefully my work helps to continue educate everyone.
Great video. Simple explanation!
i hope to be as savvy as U bro ASAP. that was bomb!!! just subscribed too thanks
Hi Keith! Very Informative video, Can you do QoS configuration next? Thank you very much! more power to you guys!
If you get the Need to configure ephone MAC address or VM station-Id error, just unplug your ephone as soon as you get the error. Make sure that both of the link lights turn red. You might have to unplug it twice. Once both are red just power your ephone back up and wait for it to register, then move on to the next ephone and repeat this process until you’re done with all three of them.
@bugraates478
3 жыл бұрын
thank you so much
@qtubetech8502
2 жыл бұрын
@@bugraates478 still showing unregistered
@judymileto1541
2 жыл бұрын
How do I configure the mac address pls
Thumbs up for training on VoIP configuration step by step with Cisco packet tracer. My question is if you have two or three Cisco switches how do you configure Voip and other vlans on the other switches
Many thanks for the video, it really useful to me. Actually I have 2911 and EHWIC ESG, I'm thinking to buy another 2960 switch to more easily configure the system.
Thanks 👍 for sharing this valuable information which I was looking for.
this is still great ! building my own network that emulates a school district and wanted to get a VOIP phone up and running.
Great job sir. Thank you very much for your time and sharing the knowledge.
Thank you for the video, appreciate it very much
thank you very much for this wonderful configuration keep doing
A very good presentation
Thanks for posting this video!
If I have two phones setup like you’ve instructed, is there a way I can program the buttons on the right of the screen so that they will call the other extension?
Hi Mr. Keith. I am attempting to register some phones with CME. Where you have the 2960, I have a 3560 in packet tracer and a 3750 in real equipment. Can you get the telephony-service with a layer 3 switch? My top router is from 2800 series in both packet tracer and the real equipment. Forgot to say. I am not using the router on a stick model.
Thank you for sharing sir new supporters here
I love this. Thanks.
wow nice! thanks very much indeed!
OK! i success ! thank you so much !! i can run VOIP on my CPTracer
Very helpful, thanks!!
Thank you A very good presentation
Hi. Thanks for the video. Where the phones already set to accept DHCP on the Voice VLAN ?
Very useful, appreciate it
this is very good for me
Great video!
Really Good Video
Good day i had hard time dealing with telephony service in my packet tracer seems it dosnt have a capability to do configuration for ip phone. Help! what should i do?
what if "switchport voice vlan " command is not available on the switch? should i configure a trunk for each port where a phone+pc are connected?
i'm following the video and have gotten up to the part where you're configuring vlan 50 as the native vlan. i'm getting an "invalid input" error? not sure why...switchport commands for the other vlans are working perfectly.
Nice video.
thakyou very much. helped me a lot
awesome video
wow awesome, thank you
So can this now be used to call regular telephone lines or are there additional configs required?
great video
But I have a seperate DHCP server for address pools so how do I config options and telephony if i'm not in dhcp?
Hi. Just a quick question. Will this topology work in the real environment without CUCME Installed on the server?
hi sir, thanks for the tutorial . but one thing that i dont understand when i dial 1020 from ip phone , the phone is connected by there is no ring there what i mean no sound of ring in the ip phone,, what is wrong with my setting ?
Great video - am not sure if I missed it , when setting up the vlan do you need to know which ports your using for the phones on the switch?
@LearnTechTraining
6 жыл бұрын
Yes, you will need to assign those ports to the proper vlans for both data and voice.
I have a question. How does the router or a dhcp server know which scope to handout to the dhcp requester. I mean the port had voice vlan and data vlan so initially when the phone boots ups its not tagging any packet so why doesnt the pc get ip from voice vlan scope and the phone from data scope?
This part is understandable and clear. i am searching for a video on how to create different subnet for computers. you have created 2 dhcp pools but phones and pc's are getting ip from one dhcp. can you extend this video to show how the pcs will get ip from .10 dhcp
@KavanMavati
4 жыл бұрын
just assigned PC to different vlan instead 10 , and make sure that vlan is part of router DHCP.
Thanks bro 😎
hi thank you but can i get extend voip document and how configer the simulation?
thanks! this was a good refresher. I am ccnp certified but I have forgotten the basics...how stupid i am now...even the connection between switch and router with subinterfaces i forgot...i just apply vlan ips to switch and communicate
@davidharrow9025
3 жыл бұрын
How long did it take you to study for ccnp before taking the exam.
@AmitThakorlovemeorhateme
2 жыл бұрын
@@davidharrow9025 I was pretty slow. I took over 2 years to prepare of the 3 modules(routing/switching/troubleshooting)
What happens if you dont set up the encapsulations for the 2811? Will the phones and desktops still work?
Do the VOIP phones strip out the vlan tags before sending the data to the computers?
i need help. what if there are 2 switches, how can i give extension to the phone connected to the other switch? they are getting the ip from dhcp but not the number. i must be missing something. the phones on only 1 switch are getting the extension
Thanks a lot, your video is very useful . I have a cisco C3900 router. when I type telephony-service it dose`t work. can I configure telephony-service in cisco 3900 router?
for some reason, his voice is very satisfying !
good job
So I'm looking on getting some Cisco phones and can you comment if you can every thing I need to do please?
im at 3:10 and im not getting the same output as you. when i enter "switchport native vlan 50" it tells me "invalid input detected at "^" marker" pointing at the "A" in Native. as far as i can tell i did everything you did a couple times. Native wouldn't appear on the "switchport ?" command because its just a name right? can you elaborate one what this command is doing? i thought you were trying to assign Fa0/1 to vlan 50 but then i seen that later on in the video it was still in default. or if you have any source that yo u can point me to about learning this it would help. im just a beginner a couple weeks into class and i want try and learn as much as i can as soon as possible.
@LearnTechTraining
6 жыл бұрын
Use command “switchport trunk native vlan 50”... the older iOS in this packet tracer allowed some legacy commands. Native vlan is required over antrunk link which helps carry non tagged vlan traffic or traffic to non Cisco devices that may or may not support tagged vlan traffic. Check out my video “understanding vlans, native vlans, trunks and .1q” on this channel.
Thank you
Hi, I am trying to learn packet tracer and this video has helped me, but can you please slow down as it's quite difficult to follow when it's going quickly. Other then that, very informative!
@jerseysama
6 жыл бұрын
play back at .75 speed. thats what i did.
Hi why I'm having problem like Configuring CM List on my packet tracer? Thanks in advance
where did you get the port 2000? From the dhcp server?
Thank you for the amazing tutorial can you please confirm if i can use the same configurations for IP telephone in ISR4331 router.
hi, y name is jorge, and i have a question in relation with switching packets between vlans, my problem is I need to segment a lan in diferent vlan one for video CCTV and other for data and even one for wifi, and my doubt is, in some PCs the user need to see the cctv control and access to the data Vlan as well, I was tinking to configure as a trunk port the interface wich connet the pc but does not work, any sugestion that avoid me to use a switch layer 3?
@LearnTechTraining
6 жыл бұрын
Hey Jorge, unfortunately there is no way to segment a network without some sort of layer 3 device. That can be a layer 3 switch, a router, or even a firewall (to a certain degree and pending iOS versions). Layer 3 switches can be found by 3rd party resellers at a fairly reasonable price (considering their cost new, of course). Your other low cost option would be having a router implemented to carry the segmented traffic to the other networks. I’m assuming cost is your concern?... if so, the only real question I’d be asking myself is per the price your willing to pay on hardware, vs the reliability. Find a used refirbished layer 3 switch with a dual power supply would be your most reliable solution for a one switch setup. Ideally, having two switches both running dual power supplies would be a cheap, redundant option for small business or home office style set up.
Very nisss splein thanks
When I was following along in the lab when I got to the part where I did the buttons it was telling me that I needed to configure the mac address or VM station-id. I don't know what I did wrong I followed the lab along with you. How do you configure the mac address for the phones?
@LearnTechTraining
5 жыл бұрын
Power off the phones and power them back on.
Hi, how can i configure the Telephony service on a layer 3 switch?
@liladounas9639
3 жыл бұрын
Hi , are you find solution ,i sech but I don't find anything 😓
Thank's
Thank you for this video. I have a packet tracer question. How did you get the gui of the telephone to be so large. Mine are small even if I click zoom. I'm thinking it's because of my screen resolution, but thought I'd ask.
Hi There: Ran into a problem while following along, When I entered the button 1:1 command for the ePhone, I got an error: Looking for a way to handle printing services and voice services in one device. Any ideas? thanks
Hi, first of all thank you so much for this , you just saved my project . Second, I'm having a bit of a problem with the 'switchport native vlan 50' command. It generates an 'invalid command' error. Can you please help?
@paolameraz1348
5 жыл бұрын
Use switchport trunk native vlan 50
great video what is the button, what is button 1: line 1 and ephone-dn 3? thanks
I have done as really physical and it works perfectly thanks good work.
greAT STUFF
Hi! Could you help me? If I write "button 1:1" it says : "Need to configure ephone mac address or VM station-id". How can I do it?
@claire_brooks
6 жыл бұрын
same prblm
@shep1sean
6 жыл бұрын
If you get the Need to configure ephone MAC address or VM station-Id error, just unplug your ephone as soon as you get the error. Make sure that both of the link lights turn red. You might have to unplug it twice. Once both are red just power your ephone back up and wait for it to register, then move on to the next ephone and repeat this process until you’re done with all three of them.
Hello Sir, I frome in Algeria. Please answer my questions. Can we give an IP address to an IP phone, so where exactly? Or the IP phone has always been forced to connect to the computer. and I'm really sorry if I have some writing errors. thank you
I have a problem with my packet tracer, when I click on the IP Phone to connect I get an error message "ALL TABS ARE IN HIDE MODE". How do I solve this?
thanks
@LearnTechTraining
5 жыл бұрын
You’rewelcome. Check out our new playlist series on Data Encapsulation!
Where can I get this program you're using? It looks like software you one uses to model different setups.
Whether this lab will come on the CCNA certification exam?
Need to configure ephone mac address or VM station-id .....that is the sms that i am receiving after configure ephone 1 and button 1:1 or 1:2 . help
@ismailsamathar4705
4 жыл бұрын
i had same problem like you how you solve it
@chriskelly4466
4 жыл бұрын
I also have the same problem. And at the end, my IP-Phone doesn't work, the director-number doesn't even appear on the IP-Phone screen. If you someone find a solution for that issue, please post it. Thanks !
@NguyenHuy-wn6es
4 жыл бұрын
@@chriskelly4466 You need to config the PC ip configuration to DHCP
I'd like to get a call centre project off the ground. Need the technical help and advice
@LearnTechTraining
6 жыл бұрын
I wish I could help you with this in more detail but that is a very loaded question. Many factors to take into consideration. My suggestion is to read up on VoIP, and Cisco Voice / Collaboration material.
3:16 I'm having issues it states error under native under letter a. I've copied the transcript exactly
hello, just one question why is the connection between the phone and the switch configured as access and not trunk??
Can i conect if i have router on a stick setup ?