Comprehensive Onewheel GT Transformation Complete Teardown and Heavily Modded Rebuild. (Pre-Update)
Ойындар
*****THIS IS FOR ENTERTAINMENT AND EDUCATIONAL PURPOSES ONLY, PLEASE DO NOT ATTEMPT****
So I've tried to make an incredibly comprehensive video on a stock to not so stock OneWheel GT transformation. This includes basic info on the Onewheel, a full tear down, and rebuild with aftermarket parts.
Pardon the rambling, this was completely unscripted, just decided to record the complete overhaul of my Onewheel GT. I tried to break it down into as many chapters as I could in order to allow for easy references back to the video. Please leave any likes, dislikes, questions, concerns, or anything else (except spam) down in the comments below. Thank you for watching.
MODIFICATIONS:
Tech-Rails 357-t skeleton rails
Tech-Rails carbon fiber rail guards
Tech-Rails Halo pads
1wheel parts Gold underlays
1wheel parts 4mm Ignite Hex tape
Version 3 sensor
The Float Life (TFL) Enduro tire
The Float Life (TFL) Lifesavers
Tech-Rails Motor plug retainer
Land-Surf Fangs (i know shut up)
CHAPTERS:
0:00 Introduction
1:38 Onewheel GT Closer Look and Features
3:51 Aftermarket Part Overview and Explanation
7:30 Tech-rails 357-T Skeleton Rails and Carbon Fiber Rail Guard Overview
9:43 Tools used explained
12:13 Factory Onewheel GT Disassembly and Teardown
20:29 Factory Onewheel GT Completely Disassemble Parts overview
21:13 Removing Factory Treaded Tire
25:12 Installing The Float Life Live Savers and Enduro Soft Compound Tire
34:04 Installing Axle Hangers
41:22 Cutting 3m Adhesive for 356 Carbon Fiber Rail Guards
53:16 Stock Treaded Tire Vs Soft Compound TFL Enduro
54:12 Installing 357t Skeleton Rails
59:33 Adding Silicone to the Sensor and Motor plug
1:02:30 Installing V3 Sensor, Gold Underlay, and 4mm Ignite HEX tape onto the Tech-rails Halo Pads
1:17:19 Installing Tech-Rails Motor Plug Retainers (DO THIS BEFORE INSTALLING THAT RAIL)
1:18:48 Video Cutout Apology. Front Sensor was tested, Grip installed like the rear, both pads installed just like factory.
1:20:43 Flight-Fin System Installed
1:32:41 Installing Rear Bumper and Fang
1:34:53 Adjusting Flight-Fins to Feet
1:36:19 Leveling the Board with new 357-t Skeleton rails using NRF connect
1:40:03 Flight Shield Install attempt (it doesn't clear the tire with 357-t's at lowest setting)
1:41:26 Overview of the Final Form
1:41:55 Outro and Thank you
I know the video is long and rambling, but I hope it helps some people out. Thanks for watching, and I hope you subscribe for more randomness.
Пікірлер: 5
For the tire removal, if you use the groove in the hub you can get the tire off without needing any tools. The tire irons can help but put a lip of the tire in that groove to get a lot more room to fit over the rim. Also recommend putting the axle block back on for better wire harness protection. A 5 gallon bucket can work for a tire restraint also. Nice build and like the continuous style you show everything in real time
SICK DUDE!!!!! That is a beautiful board! Much appreciation on grabbing the Tech Rail 357s and the Ignite Foam Grip Tape! Lets get it!
Glad you finally put this out, looks sick!
That looks so sick dude! Thanks for sharing.🤙🤙
Glad you have a thorough video man! Alot of them cut out some important stuff. Will use this video to get my WTFs on the GT-S! Since it's updated I'll level with custom shaping nose tilt. I dont usually ride backwards so not concerned about backwards unlevelness.