I was locked out of my safe just before leaving house to travel by plane ...so I panicked until I found out you don't need passport and id for kids when traveling domestic....so that saved me...but just back from vacation and I checked out all the ways this safe could be opened and I didn't want to give up...battery change, hammering on door etc etc...until I found this video which saved me an expensive visit from the locksmith...thank you!!!!! pulling out that wire from the chip and inserting it was the magic trick... however, I emptied the box and locked again and what do you know...safe is not to open again... It's getting dumped for good but I am so happy for this video :)... I have an LG353715

I had a Guardall safe with a digital La Gard keypad that was refusing to unlock following a battery change. This solved the problem. Thank you!!

Fixed our problem. Thanks!

You are a hero, thank you so much!

Worked on stack on keypad. Thanks.

Worked perfect thank you!!

Thanks so much for this video, it is very helpful and it works for me. Thanks again. God bless.

Not all keypads slide up I had to remove plastic keypad cover to access screws which destroyed it, but I was replacing the keypad and lock anyway

Awesome, you just saved me a lot of money! This fixed my problem very quickly. Thank you for the great work and keep on!

My safe I had wires corroding and I wanted to replace the wires tried removing the key pad as this video shows but after opening it and taking the inside cover off I just wound up beating and prying the key pad off found out the pad itself needed to be removed as the key pad is glued to the base that is screwed to the door of the safe I looked for video showing my key pad but did not find any. Replaced it with this style .

Woohoo. It just worked on my Winchester safe. Thanks

This just worked for the same issue on my winchester. But the ribbon cable is pretty flimsy, try to only pull on the connector and not the ribbon. I had to disconnect the ribbon for about 30 seconds for it to work. Otherwise only half the numbers would work. I hope this doesnt put me in a bind in an emergency

What’s the wiring sequence for the black red green and yellow coming from the safe to the mother board? Broke mine

Wow thanks worked perfect.

It this the same key pad as on the Winchester safes

Good afternoon , I have a sentinel 18 vault electronic gun safe , the key pad not working ,I use the key to unlock still doesn't unlock ,what can be the issue ?

Si le quitas el teclado puedo hacerlo funcionar con la tarjeta??

I have a 3802 and the keypad doesn't just slide up (thank goodness the safe is OPEN), do I have to unscrew the panel at the back of the door to remove the keypad?

Ok my lock in the door not the key punch on out Side of door. In days battery gos dead new ones go dead i think its in the door need a one is a sceurram pad just bought it 1 week ago can you help or by new all this happens in 3 days

Allan here , safe with a laGard which has the 2 flash bulbs at the bottom , stop working , changed out battery , still did not work , now Am locked out still , tried resetting combo , the problem they want you to have the door open , no matter what I have tired the door is still locked on me , will not open

Hello I have a lock and I can't change the password. Is set to just 1 and I want to set it to 6 numbers. This will hard reset the lock?

This actually helped me I’ve not been able to open my gun safe in almost a month and I’ve tried to reset it before but it didn’t work then I tried it this way and it finally opened

now does this work if you changed the factory combination and forgot the combination that you put it as?

@dlevi67

3 жыл бұрын

Nope. It only resets the processor for the keypad. The code is stored in the lock itself, inside the safe.

@jayonez137

3 жыл бұрын

@@dlevi67 Yes sir

First pointer- do this with the door OPEN and test it before you close it!

I encountered problem with la gard safe lock. I forgot my code and can't open the safe lock. How can I resolve this problem?

Is this the way to unlock this type of lock when it quits working? A friends Winchester safe with same lock quit working and won't open now, common issue apparently. But the support line is never answered and cant even leave a message because it's full so they dont want to hear from their customers unless it's to sell a new safe. I hope this can work with his. Thanks for the video!

@fritzs1207

2 жыл бұрын

yep >>> they are the real safe thief

Hi I don't know if this is the place to ask this.I have a safe that uses the lg basic 3710. The keypad has stopped working and the safe is locked. There is no power going to the key pad even though I've replace the 9V battery with a new one. The supplier is charging me more than the cost of a new safe to get access to my contents (I feel as if I'm held to ransom). Can I peel off the existing keypad and replace it with a new electronic Lagard keypad, get the safe door opened opened, get access to my contents and have a working safe? Thanks

@roycheney5573

5 жыл бұрын

Did you ever finda solution? I'm having the same problem!!

@htcones99

5 жыл бұрын

Maybe the wires of the battery are broken

@donc9751

5 жыл бұрын

Wow. This question is 2 years old and no answer! I guess I better not hold my breath for mine to be answered .

@johnciszewski578

4 жыл бұрын

@@roycheney5573 I had problem remove battery wait 10 seconds press 0 wait 5 seconds and replace battery and see if that works. Worked for me

@johnciszewski578

4 жыл бұрын

@@donc9751 I had same problem remove battery wait 10 seconds press 0 wait 5 seconds and replace battery and see if that works. Worked for me

I tried this method but unfortunately it didn't work for me. My situation before trying out this method was some of the number doesn't make a beep (I assume that means it doesn't register). After trying this method the all numbers (at least the ones I need) now beep but it's still not opening. Is it possible the number I press and the and the actual numbers that register could be different? I'm 100% sure I got the right combination, I have used the same number for 10 years and only I have access to this safe.

@CP-ux9zd

Жыл бұрын

if you have a particular number press not beeping, then that membrane is bad. You can replace just the keypad .. all from the outside of the safe. Should get you going

Mine is hard to come off should I tap it with something ?

@CP-ux9zd

Жыл бұрын

heel of your hand. Bump up sharply. Be ready to catch it so the small wires dont get damaged if it detaches

I have a Liberty electronic panel safe that the keypad doesn't respond even with a new battery. Unfortunately it is in a locked position. How can I get this thing open? At one time today the small led light did blink a few times.

@roycheney5573

5 жыл бұрын

Did you ever get this resolved? I have the same problem!!

@arrowhunter2

5 жыл бұрын

did you get this fixed? mine is the exact same way

@Supranforever

4 жыл бұрын

Same here.

@doncena7193

2 жыл бұрын

I have a Winchester and when I started to replace the 9v, the lead wires for the 9v to the lock mechanism were spliced together. I found that to be weird. So when I took off the wire cap from the 9v, I saw the spliced wires were connected by a small piece of masking tape and the red wire had come loose. I started to examine and couldn’t believe both red/black the wires were spliced. Why they didn’t make both the red and black wires just one whole lead wire is surprising to me. Anyways they both ended up coming apart and trying to re wire them is a pain because there’s not enough wire in that small area to do it! Mind you these wires are the thinnest ones. So I jimmy rigged it just to get a connection and used a cheap 9v. After so many tries for 1-1/2 hours, I read online that these safe locks only use Duracell or Energizer 9v batteries. So I actually found a Duracell in the kitchen drawer and it actually freakin worked! Omg! A lot of these safes only work with Duracell batteries! Might have to replace all the wire leads to one grade thicker. And if I eff that up, then I would have to replace the entire keypad! I’m not looking forward to this project at all! Damit

@CP-ux9zd

Жыл бұрын

@@doncena7193 someone probably pinched and damaged the wires rehanging the combo onto the pins. Or, they removed the lock and let it fall yanking the wires apart. They are always continuous from battery to inside lock mechanism

didn't work

Winchester 24 gun safe, La Gard keypad just quit working. How do I remove the cover plate? Slide it, tap it? Changed batteries 3 times, it's dead.

@assassin18530

4 жыл бұрын

When this does not work, here is a solution that will; I found articles where the keypad on the LaGards start to go out. You can try this and it may work, when it does not work though, gently pull the keypad off of the metal housing (yes, it is lightly glued to that housing), You will need to pull the ribbon cord out of the control board, just as in the video. After you have removed the keypad itself, put some painters tape onto the surface of the housing where the keypad was adhesively attached to. Cover the entire surface of the area with the tape where the keypad was. Now, put the keypad back onto the area you just applied painters tape too, you can tape the edges of the keypad or you can use another adhesive. Connect the ribbon cable back to the control board, then attach the battery, and test. If you are entering the correct code, it should open. The keypad is touching the housing or the adhesive is causing the contacts to not read correctly. The tape will insulate from this affect. I hope this helps

@Eddie_the_Husky

3 жыл бұрын

@@assassin18530 thank you for this.

@clifflowery9559

2 жыл бұрын

@Richard Eubanks You’re the man! Fixed my Winchester safe

How does that model not have a 5 minute lock out penalty for removing the battery?

@TOMVUTHEPIMP

5 жыл бұрын

It only lock you out of you put in the wrong code.

@loodeytunes

3 жыл бұрын

Not an expert on this at all but by logic there is no need to lock you out because it doesn't change your code in anyway.

You dont have to do all of that. Unplugging battery has same result.

@CP-ux9zd

Жыл бұрын

maybe sometime

What was you trying to achieve ? There was nothing wrong with the keypad anyway ... I'm not aware of disassembling and reassembling a keypad to reset or fix any problems.. Its usually the membrane on the key pad