Very nice Video, Dominator 85 became pretty rare. Especially in this great condition.

Awesome ! Brought back my childhood memories of dad harvesting :)

This Claas Dominator 85 looks great! I myself have a Ihc321 harvester! MfG LandFreak

I like the colour coordinated shirt !

Au début des années 1970 1975 j'ai battu au coté de ces machines là , en entreprise , avec SOMECA M 152 ... C'était la guerre au bout des champs , à qui voulait faire ses moissons avant l'autre ! SOMECA ou CLASS peut importe, des machines de même gabarit , fallait-il satisfaire les clients ! Parfois nous autres les chauffeurs nous étions menacés ?! Les gens venaient jusqu'à courir le risque sur la route de passer la machine et s"arrêter net en travers devant la barre de coupe puis monter avec menace de coups , nous obligeant à faire demi tour pou aller faire leur champ . l"époque était à la rude concurrence des machines et des bons chauffeurs de conduite ; MERCI de cette belle vidéo ! J B ( Vesoul ) FRANCE le 26/12/17

@martinejoseph1644

6 жыл бұрын

PARDON pour la faute de frappe de la marque qui est > je vous prie de bien vouloir m'en excusé ....

woow, exelent video

Great!

Nice

I'm impressed from the speed of that combine do its work! :D I was joking :) it is good to be yet there at work!

@steigerpower

5 жыл бұрын

One does question with the growth of hi tech combines n their huge capacity just how few farm hands will be employed each harvest compare to the combines of this era.

He better get some ear-muffs, or he'll end up like my grandpa, damn near def.....

it is very funny I like

Hello I would like to know how to adjust the claas 85 for wheat harvest, because I worked a campaign and there was a clogg between the 2 sites ( the mall one and the big one ) and it made it dirty. I would like to know at what rpm is optimal for wheat harvest.

@ASPCOT

5 жыл бұрын

Hedesan Efrem Run the cylinder about 1100-1350 rpm, use wheat sieves if you have them ( 7/ 32" oblong holes ). When using sieves, remove the chaffers from the combine and install the adjustable sieves where the chaffers were and install the finishing sieves below. Without finishing sieves, open the chaffers 3/8" and the adjustable sieves only just open. Observe the tailings, which will be heavy, and slowly open the sieves until the tailings are at a minimum without putting too much trash in the grain tank. Wind blast should be 80. Preliminary concave adjustment to be made outside the combine, observed through inspection ports. Cylinder/concave clearance at the front should be 1/2" with adjustment lever in cab placed at the second hole from the top of the quadrant. Rear clearance should be 3mm. If not feeding steady and slugging the cylinder, try additional auger flighting at the center of The auger, to push the crop farther into the center, into a tighter pile, so the fingers can grab it and throw it into the feed rake. Raise the beater flap to throw the straw farther out onto straw walkers if you have green weeds, or they will be pulverized and end up on the sieves and make separation difficult. If white caps appear, try engaging the auxiliary threshing plate , and/or close the sieves and increase the tailings until the grain begins to crack.

I thought the same.

Sounds like a V8

harvest machine rate of cost

Does that have a two-cycle Detroit Diesel in it?

@johnplagge7928

8 жыл бұрын

+trackhoe23 120HP Mercedes

@denischambrelent8286

Жыл бұрын

@@johnplagge7928 is a Mercedes OM 352??

Habe gleiche Maschine mit vollhangausgleich

@zzzzzz1220

3 жыл бұрын

Wir hatten auch mal so einen ohne hang Ausgleich mein Vater saget im Hang teilweise ging dann das schneidwerk über die ehren aber mit Kabine und Klima aber die nicht funktionierte ;)

Oliver

O