Changing a heater resistor on 2002 Citroen Xsara Picasso
Жүктеу.....
Пікірлер: 52
@gazhammer82173 жыл бұрын
Just want to say a big Thank You having found this video. My 2006 Xsara Picasso heater blower had packed up on all bar the number 4 setting. Ordered a replacement heater resistor which cost about £9 and after following your advice it was changed in about 40 minutes. The fan unit just twisted straight out on mine really easy with no lug to faff about with. The hardest part was getting the wiring connector off the old resistor unit as you have to feel your way, whilst contorting your body, on the connection and squeeze both the lugs and off it comes. Popped the new one back in really easy and bingo a working fan on all settings again. I might add there are some sharp bits where your head has to go where the glovebox was so be careful out there. Other than that Brilliant - Thank You!
@neilsmith6663 жыл бұрын
I looked everywhere on the internet for these type of instructions, none in my opinion were logical and easy to understand EXCEPT for this one. Absolutely brilliant, thank you so much for sharing your video with everybody, first class.
@phil_paine5 жыл бұрын
This is BRILLIANT! Thank you for showing and by doing this I saved a load of time, money and effort. The Haynes manual tells you nothing except to take off the lower fascia. I followed this and by removing the glove box, take off the panel below first, then the door, the 10mm nut and washer below the glove box. Then I removed the 4 T20 screws on the lower part of glovebox and the rubber stopper T20 screws at the top and wit a gentle lift out it came. Now I could see the motor and a gentle amount of tugging removed the connector and slid it upwards over a cable to keep it out of the way. I used a flat blade screwdriver gently under the lock clip of the motor and it turned easily clockwise. It is as fiddly as anything to get it out but gently does it and it's out of place. Carefully (I bashed my head and it did hurt!) look and see where the resistor pack is and using one hand rotate it and it drops down enough to squeeze the clips on top and prise the connector off with one hand as there is NO WAY to get 2 hands in here! I ordered a replacement from eBay and waited overnight, took the dog out for a walk this morning and on return the resistor pack was delivered. Easy to fit in place and twist to lock in position. The motor is carefully jiggled back into place and locked, connector fitted, ignition switched on and engine running and YES the fan now works properly wit 4 proper speeds which it never did before. Cleaned up all the bits of the glovebox and replaced in position and checked the glovebox lamp was working. Re-stashed CD's, paper cups and lids, napkins, picnic knife, fork and spoons and replaced the McD's salt, pepper, ketchup and BBQ sauces and we're ready to go. Thank you so much BlackCatEveG for this as I would have been trying to figure it out for ages! My Citroen Xsara Picasso, 2.0HDi (90kw) is a 54 plate so 2004 and is our best vehicle for travelling distances and taking our lovely big dog with us too. Off to take it out for a trip now - taraa
@danielroberts15595 жыл бұрын
A big thank you - AC suddenly stopped working. Got gas coolant levels checked and as they were fine the garage (Kwik-Fit) reckoned it was the heater motor at fault. A browse through KZread led me to this video and within no time I had the motor out. Before buying a new one I tried refitting the old one to check I could and amazingly it worked when refitted! My glove box has an AC vent leading into it but this just clipped out with the help of a screwdriver. Thank you - super helpful video.
@onlyKentrop5 жыл бұрын
I honestly cannot thank you enough for this. Just changed the one on mine (2007 N86 variant, but has the exact same setup), and I'm just a lowly IT nerd whose knowledge of cars basically used to be changing a tyre, and knowing which liquid goes where. That said, it's an unmitigated pain in the shoulder to do, but it's done, and I now have a working variable blower again. If I knew where to send it, there's a pint with your name on it!
@richardmounfield78223 жыл бұрын
Magic got one to do this afternoon at work . Glad I found your video
@wheelsofrust14 жыл бұрын
Great help thanks! Re, Terry Crick's comment below, after freeing the motor, I took off the loom connection plug on the bottom right (its on a clip on the bulkhead and can be slid off), the one with a green and yellow earth looking wire in your video, and that made it much easier to get the motor out. Finding the little tags on top of the old resistor pack to squeeze was the hardest part as you can't see and there is only about 1" of loose cable.
@terrycrick36005 жыл бұрын
Saved me a lot of money,last time the garage replaced the whole unit! Had to struggle a bit with the tight space but got there in the end! Many thanks.. Terry.
@johnholland29624 жыл бұрын
Great video, never even realised what was causing the problem til I watched the video, well explained too! thanks a lot!
@pauldirlea59613 жыл бұрын
Just done mine. 2010 model xsara Picasso. Everything went exactly how you described it and it was a roughly 30 minute job. Thank you ever so much! 👌
@skellyking95 жыл бұрын
Very useful video. Can do the next 1 a lot quicker now. So straight forward to understand what this chap is saying
@Kev24286 жыл бұрын
Thanks very much. Like Jason said, the only decent guide I could find for this job.
@jonathanmay45264 жыл бұрын
Excellent vid, it was a great help, later facelift models are the same.
@ulotsukit6 жыл бұрын
Thanks to your vid I fixed mine today. 👍
@MrTrudgian15 жыл бұрын
Brilliant, only instructions I could find anywhere. Longest bit was getting the glove box out and working out how to twist the motor. Managed to break the tab but still seems secure, easier for next time. Managed to get my head right under to see the resistor connector which made it easier. Motor working ok on all settings. Thank you! Ps there are 11 X T20 Tork screws and 1 X 10 mm bolt in the glovebox to get it out
@gerrydance49
5 жыл бұрын
Agree with mark R Trudgian. Super, very well explained and filmed instructions. Many thanks BlackCatEveG! I did the same thing and broke tab on the motor, it's an easy thing to do with not much access & lying on the shingle drive. Much easier to do up on ramps standing upright! Motor fixed in place & all works great. Before I started the job I was quoted £200 from local garage to replace the motor because that's the fault. Oh no it's not, it's a £10 resistor!
@neilsmith666
3 жыл бұрын
@@gerrydance49 Could you easily turn the motor clockwise ok after lifting the tab or breaking off the tab ??, It seems pretty tight ? Is there a need to remove the shiny torx screw on the front of the casing as shown in the video. I dont want to remove it and something falls off inside !! Would be great if you could let me know.
@gerrydance49
3 жыл бұрын
@@neilsmith666 I did exactly as instructed. The Motor will turn clockwise after lifting the tab, with a little persuasion. I believe I did need to remove the torque screw as instructed to enable me to remove the glove box for full access to motor. Nothing should fall inside. ( put a small rag to stop the torque nut falling behind carpet if you're concerned.) Good luck & let me know how you get on. It is a simple job. Just make yourself comfortable on the passenger floor leaning upside down!
@neilsmith666
3 жыл бұрын
@@gerrydance49 Many thanks for your reply, its very kind of you.I've ordered the resistor , that was a challenge within itself !! and will fit it at the weekend, I will let you know the outcome and how many times i have banged my head LOL !!
@gerrydance49
3 жыл бұрын
@@neilsmith666 Hi Neil, Hope it all goes OK. Have a good torch, it will prove very useful. Once the glove box is removed. You'll see the motor. I didn't need to be too heavy handed lifting the tab on the motor, lifted it with a flat bladed scewdriver. The motor should rotate OK. Have the paracetamol to hand : ))
@suemayedgar21585 жыл бұрын
Did mine today thanks so much for your vid, if I have done a vid there would be a lot of blepps put in lol
@jasond49657 жыл бұрын
Thanks, only video i could find that showed me right information for my car
@evegilly5404
7 жыл бұрын
Your welcome Jason Davage
@jasond4965
7 жыл бұрын
unfortunately for me, its not the resistor, put new 1 in today but fan still only works on full :(
@glynduffield23832 жыл бұрын
If you break the tab when removing the motor (shown at 1 :32), don't worry. When you refit the motor there is a screw hole at about the 1 o'clock position that you can just start a self tapping screw in. Don't screw in tight, it's there to stop the motor rotating
@aninterviewwith...17023 жыл бұрын
Thank you for this video. Really helped.
@hugonilsson6067 Жыл бұрын
My motor seems to be facing the steering wheel side since i have the steering wheel on the left, not sure how i will däget this done now
@paulmortimer64246 жыл бұрын
the black tab is hard to get at so I threaded a bit of old throttle cable and used that to pull it much easier. Plus make sure you need a resistor pack not a controller.
@versys5192
6 жыл бұрын
Paul Mortimer ttull L
@AccessRealityTruth3 жыл бұрын
Thanks a lot!
@damjan95487 жыл бұрын
My blower sometimes stops for 30 sec and then starts again... usaly when car is cold... is ti resistor? please help me
@darkoblazevski84986 жыл бұрын
De se nalazi sirena na citroen pixaso 2005 godina i gde se nalazi osigurac za sirenu
@ivicacorak90735 жыл бұрын
Where is sensor air themperature on Picasso 2001. 1.6
@spassser4 жыл бұрын
thanks on my car that is left hand steering this is a bit harder..
@jancarstens4262
4 жыл бұрын
Fik du den ud i venstre side ved rattet uden de store problemer? Jeg skal til samme manøvre :(
@spassser
4 жыл бұрын
@@jancarstens4262 ja det faktisk ikke så slemt men du skal have ratstammen af foroven for at få blæser ud sørg for at du låser rattet ewt med en bagege elastik ting så rattet ikke drejer imens du arbejder for så sprænger du ledninger til airbag blæser er låst fast med en lille plastik lås der kan vippes ud med en lille skrue trækker så kan blæser lige drejes ud havde begge mine arme virket vil jeg tro man kunne gøre det på en god halv time
@jancarstens4262
4 жыл бұрын
@@spassser Hmm lyder sgu lidt træls med ratstammemanøvren, men må se på det når jeg kommer hjem. Og det er ikke muligt at kringle den ud, uden at afmontere den foroven (og hvor er det,- er det nemt at spotte hvad du mener, når man ser det?)
@spassser
4 жыл бұрын
@@jancarstens4262 ratstammen har en blind stråle.. Kan kun sidde på en måde den er ikke noget problem det hele kan fint lade sig gøre..
@jancarstens4262
4 жыл бұрын
@@spassser ok,- jeg må se på det. Bare sådan noget med rat, det skal være samlet sådan nogenlunde rigtigt, så er ikke så meget for at rode med det. Men er det ligetil som du skriver, så er det vel ikke så svært.
@jamesburton3172 Жыл бұрын
Fk that, i have 1, 2, an 3 working.... ill pass on getting 4 working.
Пікірлер: 52
Just want to say a big Thank You having found this video. My 2006 Xsara Picasso heater blower had packed up on all bar the number 4 setting. Ordered a replacement heater resistor which cost about £9 and after following your advice it was changed in about 40 minutes. The fan unit just twisted straight out on mine really easy with no lug to faff about with. The hardest part was getting the wiring connector off the old resistor unit as you have to feel your way, whilst contorting your body, on the connection and squeeze both the lugs and off it comes. Popped the new one back in really easy and bingo a working fan on all settings again. I might add there are some sharp bits where your head has to go where the glovebox was so be careful out there. Other than that Brilliant - Thank You!
I looked everywhere on the internet for these type of instructions, none in my opinion were logical and easy to understand EXCEPT for this one. Absolutely brilliant, thank you so much for sharing your video with everybody, first class.
This is BRILLIANT! Thank you for showing and by doing this I saved a load of time, money and effort. The Haynes manual tells you nothing except to take off the lower fascia. I followed this and by removing the glove box, take off the panel below first, then the door, the 10mm nut and washer below the glove box. Then I removed the 4 T20 screws on the lower part of glovebox and the rubber stopper T20 screws at the top and wit a gentle lift out it came. Now I could see the motor and a gentle amount of tugging removed the connector and slid it upwards over a cable to keep it out of the way. I used a flat blade screwdriver gently under the lock clip of the motor and it turned easily clockwise. It is as fiddly as anything to get it out but gently does it and it's out of place. Carefully (I bashed my head and it did hurt!) look and see where the resistor pack is and using one hand rotate it and it drops down enough to squeeze the clips on top and prise the connector off with one hand as there is NO WAY to get 2 hands in here! I ordered a replacement from eBay and waited overnight, took the dog out for a walk this morning and on return the resistor pack was delivered. Easy to fit in place and twist to lock in position. The motor is carefully jiggled back into place and locked, connector fitted, ignition switched on and engine running and YES the fan now works properly wit 4 proper speeds which it never did before. Cleaned up all the bits of the glovebox and replaced in position and checked the glovebox lamp was working. Re-stashed CD's, paper cups and lids, napkins, picnic knife, fork and spoons and replaced the McD's salt, pepper, ketchup and BBQ sauces and we're ready to go. Thank you so much BlackCatEveG for this as I would have been trying to figure it out for ages! My Citroen Xsara Picasso, 2.0HDi (90kw) is a 54 plate so 2004 and is our best vehicle for travelling distances and taking our lovely big dog with us too. Off to take it out for a trip now - taraa
A big thank you - AC suddenly stopped working. Got gas coolant levels checked and as they were fine the garage (Kwik-Fit) reckoned it was the heater motor at fault. A browse through KZread led me to this video and within no time I had the motor out. Before buying a new one I tried refitting the old one to check I could and amazingly it worked when refitted! My glove box has an AC vent leading into it but this just clipped out with the help of a screwdriver. Thank you - super helpful video.
I honestly cannot thank you enough for this. Just changed the one on mine (2007 N86 variant, but has the exact same setup), and I'm just a lowly IT nerd whose knowledge of cars basically used to be changing a tyre, and knowing which liquid goes where. That said, it's an unmitigated pain in the shoulder to do, but it's done, and I now have a working variable blower again. If I knew where to send it, there's a pint with your name on it!
Magic got one to do this afternoon at work . Glad I found your video
Great help thanks! Re, Terry Crick's comment below, after freeing the motor, I took off the loom connection plug on the bottom right (its on a clip on the bulkhead and can be slid off), the one with a green and yellow earth looking wire in your video, and that made it much easier to get the motor out. Finding the little tags on top of the old resistor pack to squeeze was the hardest part as you can't see and there is only about 1" of loose cable.
Saved me a lot of money,last time the garage replaced the whole unit! Had to struggle a bit with the tight space but got there in the end! Many thanks.. Terry.
Great video, never even realised what was causing the problem til I watched the video, well explained too! thanks a lot!
Just done mine. 2010 model xsara Picasso. Everything went exactly how you described it and it was a roughly 30 minute job. Thank you ever so much! 👌
Very useful video. Can do the next 1 a lot quicker now. So straight forward to understand what this chap is saying
Thanks very much. Like Jason said, the only decent guide I could find for this job.
Excellent vid, it was a great help, later facelift models are the same.
Thanks to your vid I fixed mine today. 👍
Brilliant, only instructions I could find anywhere. Longest bit was getting the glove box out and working out how to twist the motor. Managed to break the tab but still seems secure, easier for next time. Managed to get my head right under to see the resistor connector which made it easier. Motor working ok on all settings. Thank you! Ps there are 11 X T20 Tork screws and 1 X 10 mm bolt in the glovebox to get it out
@gerrydance49
5 жыл бұрын
Agree with mark R Trudgian. Super, very well explained and filmed instructions. Many thanks BlackCatEveG! I did the same thing and broke tab on the motor, it's an easy thing to do with not much access & lying on the shingle drive. Much easier to do up on ramps standing upright! Motor fixed in place & all works great. Before I started the job I was quoted £200 from local garage to replace the motor because that's the fault. Oh no it's not, it's a £10 resistor!
@neilsmith666
3 жыл бұрын
@@gerrydance49 Could you easily turn the motor clockwise ok after lifting the tab or breaking off the tab ??, It seems pretty tight ? Is there a need to remove the shiny torx screw on the front of the casing as shown in the video. I dont want to remove it and something falls off inside !! Would be great if you could let me know.
@gerrydance49
3 жыл бұрын
@@neilsmith666 I did exactly as instructed. The Motor will turn clockwise after lifting the tab, with a little persuasion. I believe I did need to remove the torque screw as instructed to enable me to remove the glove box for full access to motor. Nothing should fall inside. ( put a small rag to stop the torque nut falling behind carpet if you're concerned.) Good luck & let me know how you get on. It is a simple job. Just make yourself comfortable on the passenger floor leaning upside down!
@neilsmith666
3 жыл бұрын
@@gerrydance49 Many thanks for your reply, its very kind of you.I've ordered the resistor , that was a challenge within itself !! and will fit it at the weekend, I will let you know the outcome and how many times i have banged my head LOL !!
@gerrydance49
3 жыл бұрын
@@neilsmith666 Hi Neil, Hope it all goes OK. Have a good torch, it will prove very useful. Once the glove box is removed. You'll see the motor. I didn't need to be too heavy handed lifting the tab on the motor, lifted it with a flat bladed scewdriver. The motor should rotate OK. Have the paracetamol to hand : ))
Did mine today thanks so much for your vid, if I have done a vid there would be a lot of blepps put in lol
Thanks, only video i could find that showed me right information for my car
@evegilly5404
7 жыл бұрын
Your welcome Jason Davage
@jasond4965
7 жыл бұрын
unfortunately for me, its not the resistor, put new 1 in today but fan still only works on full :(
If you break the tab when removing the motor (shown at 1 :32), don't worry. When you refit the motor there is a screw hole at about the 1 o'clock position that you can just start a self tapping screw in. Don't screw in tight, it's there to stop the motor rotating
Thank you for this video. Really helped.
My motor seems to be facing the steering wheel side since i have the steering wheel on the left, not sure how i will däget this done now
the black tab is hard to get at so I threaded a bit of old throttle cable and used that to pull it much easier. Plus make sure you need a resistor pack not a controller.
@versys5192
6 жыл бұрын
Paul Mortimer ttull L
Thanks a lot!
My blower sometimes stops for 30 sec and then starts again... usaly when car is cold... is ti resistor? please help me
De se nalazi sirena na citroen pixaso 2005 godina i gde se nalazi osigurac za sirenu
Where is sensor air themperature on Picasso 2001. 1.6
thanks on my car that is left hand steering this is a bit harder..
@jancarstens4262
4 жыл бұрын
Fik du den ud i venstre side ved rattet uden de store problemer? Jeg skal til samme manøvre :(
@spassser
4 жыл бұрын
@@jancarstens4262 ja det faktisk ikke så slemt men du skal have ratstammen af foroven for at få blæser ud sørg for at du låser rattet ewt med en bagege elastik ting så rattet ikke drejer imens du arbejder for så sprænger du ledninger til airbag blæser er låst fast med en lille plastik lås der kan vippes ud med en lille skrue trækker så kan blæser lige drejes ud havde begge mine arme virket vil jeg tro man kunne gøre det på en god halv time
@jancarstens4262
4 жыл бұрын
@@spassser Hmm lyder sgu lidt træls med ratstammemanøvren, men må se på det når jeg kommer hjem. Og det er ikke muligt at kringle den ud, uden at afmontere den foroven (og hvor er det,- er det nemt at spotte hvad du mener, når man ser det?)
@spassser
4 жыл бұрын
@@jancarstens4262 ratstammen har en blind stråle.. Kan kun sidde på en måde den er ikke noget problem det hele kan fint lade sig gøre..
@jancarstens4262
4 жыл бұрын
@@spassser ok,- jeg må se på det. Bare sådan noget med rat, det skal være samlet sådan nogenlunde rigtigt, så er ikke så meget for at rode med det. Men er det ligetil som du skriver, så er det vel ikke så svært.
Fk that, i have 1, 2, an 3 working.... ill pass on getting 4 working.