Thanks for the video. I had no idea the priority was based on the MAC addresses!

@networktutor640

3 жыл бұрын

Glad it was helpful!

@iankz4144

2 жыл бұрын

I think its based on uptime first then it looks at the priority number and if ita not set then it would look at the MAC

very good video, straight to point

@networktutor640

Жыл бұрын

glad it helped

Thank you very much sir.. easy way understand it m

@networktutor640

3 жыл бұрын

Always welcome

Thank you sir

Thank you so much!

@networktutor640

Жыл бұрын

You're welcome!

Thanks for your great contents. I have a question. Say we add a third switch to our two members switch stack which its mode is "Bundle" and we want to make it as "Install" mode so it can join our "Install" mode stack. Do we have to change its mode individually and before putting the stack cables on and then connect it to the stack or we can add it as is and make a V-mismatch and then console to the new member and change its mode and reload it ? This area is kinda vague to me. Could you please explain? And sorry I have to pose my second question that just sparked in my mind. How about the license mismatch? How do we match them? And why the license has to be the same? Thanks beforehand.

@JKRowl

Жыл бұрын

Hello. I’m not familiar with your question regarding bundle/install mode. May you please let me know where did you study this from? Which course?

Thanks from india.

@networktutor640

2 жыл бұрын

you are welcome

thank you , document of de Cisco , no understand , the video is very simple is the explication easy of the understand

@networktutor640

2 жыл бұрын

Glad it was helpful!

Another question? Are all the files in all the stack members' flashes autogrnarated once the stack is forming? So if we format all switches flashes and only having the .bin Image file, we shouldnt run into any problems right?

@rafay1708

2 жыл бұрын

hi, yes, u can delete all file but do not delete the (.bin) or (.tar) because it is the OP of it. one suggestion, before to delete all try to backup all file in case of lose. you can do it with TFTP-Server software.

if i have 6 stack switch and 2nd switch has been down than how to find the faulty switch ?

Here did you say if I had two switches for example 9200 and I would like to put hem in stack I just need to connect the stack cable and the swtiches automatically formed the stacking? Don't I need to make a previous configuration?

@networktutor640

2 жыл бұрын

if you are adding a second switch to the existing 9200 switch, the second switch will get the config from the already running 9200. Look at this video and you will understand well. kzread.info/dash/bejne/mqGnlpZuhavLf7A.html Hope this helps.

Great 👍🏼👍🏼

@networktutor640

2 жыл бұрын

Thank you 👍

Hello Network Tutor Nice video.. i'm new on networking, i'm planning to add a new cisco 2960x on existing stacks. The switch i will add is not new. Do i need to reset it to factory default before it to the stack?thanks..

@sanjayk4356

3 жыл бұрын

No, just add and set a priority level only , thn it will detect

@networktutor640

Жыл бұрын

it is better if you reset it to factory default. You need to erase the vlan.dat and write erase. This will make all the old vlans goes away. See this video - kzread.info/dash/bejne/YouT1bGTmbDUZNI.html

what about the configuration please ? does the master configuration apply to all other switches ?

@networktutor640

3 жыл бұрын

All stack members store a copy of the configuration settings. If a stack master becomes unavailable, any stack member assuming the role of stack master will operate from the saved configuration files. Say if you have 2 switches in stack, issue the command - sh flash2: and see - you will have the same config file there too.

Sir. Do we have to reload both switches in order for the change of priority to work?

@networktutor640

Жыл бұрын

if you are adding a new switch - you don't have to reboot the stack. for example if you are adding a second switch to the stack - set the second switch priority to 14 (assuming your first switch is @ priority 15) and just add it to the stack. no reboot needed. let me know if this is what you are asking?

Thank you

@networktutor640

Жыл бұрын

You're welcome

Sorry to ask, I'm just new to this kind of set up. . May I ask What will you get for doing this kind of set up.

@networktutor640

10 ай бұрын

In short - when you need more ports than a single switch then you need to add more switches to the stack to add more capacity. If you are new i would recommond to google it and learn more on switch stacking. Do you wanted to be a network tech/engineer ?

how do you identify which physical switch is member 1 or 2?

@TheEricLancaster

2 жыл бұрын

In global config mode: switch renumber

@networktutor640

2 жыл бұрын

Did you try this cmd -- Switch#sh switch - this will list all the switches in the stack and tells you which one is master and which ones are member.

how to see running configuration in this stack and how to take console in this stack

@networktutor640

3 жыл бұрын

you use #sh run to see the running config of the entire stack and with regards to console access you can console into any switch in the stack. Running config will be copied to all the switch in the stack

@sanjayk4356

3 жыл бұрын

Show running-config - u can see all details here Show switch details - stack details

existing stack how can we add the switch.!?

@networktutor640

4 жыл бұрын

If you have a new switch, just power off the stack and add it using the stacking cable. Before add the switch, make sure to set the slot priority. Also when you power up the stack, turn on the master first. But if you have each switch priority set correct, master election happen automatically.** Main think - don't turn on the blank switch first. it will blank all the stack config. by becoming the master switch.Sorry for the late response.

@ajithm1138

4 жыл бұрын

@@networktutor640 thank you for your response.

got this message Both links down, not waiting for other switches

@networktutor640

Жыл бұрын

sorry that i didn't respond earlier. hope you figured it out.

Please reply 1.Highest priority 2. Lowest mac

hey show your topology