How to change an axle shaft on a chevy or GMC truck.
Жүктеу.....
Пікірлер: 22
@Sandshredder23 ай бұрын
Couldn’t replace the sway bar bushings, on both sides?
@calholli3 ай бұрын
If you're doing this on your own car and you're poor :) ... Buy a little bottle of PR-40.. It's super strong at glueing rubber back togther. You Squirt a good bit of grease back in there and glue it back together with some clamps holding it.. and pour a little bead over the cut again later.. It will likely out last the bearings at that point
@jeffreykreft54423 ай бұрын
Seriously I got to say that’s the easiest axle swap I’ve ever seen, good job to the engineers that engineered this design. Now Ford boys,take note!
@DoubleTap1115
3 ай бұрын
Replace often. Weaknesses is the way.... GM boys!!
@Lost10mm.
3 ай бұрын
Subaru has some pretty easy axles.
@BWalker-yg9en
2 ай бұрын
@@DoubleTap1115my ford went through 2 CV axles in 50k miles. The vacuum actuated hubs ford uses are garbage and a pain in the ass when changing the axle. Chevy switched from torsion bar's to coil springs so they're not that easy to change anymore either because it's in the way now. They're both weak.
@markchidester62393 ай бұрын
That was an easy one!
@user-oc8xc1eo4i3 ай бұрын
I done that before
@ypicklegreen55973 ай бұрын
Must be nice to work on a rust free truck
@calholli
3 ай бұрын
Just move away from there.. There's a huge country down here without salt problems
@Dickey662 ай бұрын
Simple fix
@thomascoker36003 ай бұрын
Why does every job on the net seem easy until you try it yourself?
@markhuyette85093 ай бұрын
Me too 😂
@USSinGen902 ай бұрын
My only question is why don't you power wash all that stuff because now you got all that dirt I'm not judging I'm just saying
@blairarcher89523 ай бұрын
Super glue
@arod7623 ай бұрын
Get a car wash
@pjstpierre2340
3 ай бұрын
Maybe the “owner” will take your advice
@michaelfranklinwhibley29353 ай бұрын
No comment
@jerrydawg44343 ай бұрын
No lube on the sway bar bushings? Squeek much?
@Admiral_Potato41
3 ай бұрын
I've honestly never lubed up the bar or bushings on any of my trucks/cars and I've never dealt with a squeak. Could be the insta-new england-rust that forms on anything immediately. Lol
Пікірлер: 22
Couldn’t replace the sway bar bushings, on both sides?
If you're doing this on your own car and you're poor :) ... Buy a little bottle of PR-40.. It's super strong at glueing rubber back togther. You Squirt a good bit of grease back in there and glue it back together with some clamps holding it.. and pour a little bead over the cut again later.. It will likely out last the bearings at that point
Seriously I got to say that’s the easiest axle swap I’ve ever seen, good job to the engineers that engineered this design. Now Ford boys,take note!
@DoubleTap1115
3 ай бұрын
Replace often. Weaknesses is the way.... GM boys!!
@Lost10mm.
3 ай бұрын
Subaru has some pretty easy axles.
@BWalker-yg9en
2 ай бұрын
@@DoubleTap1115my ford went through 2 CV axles in 50k miles. The vacuum actuated hubs ford uses are garbage and a pain in the ass when changing the axle. Chevy switched from torsion bar's to coil springs so they're not that easy to change anymore either because it's in the way now. They're both weak.
That was an easy one!
I done that before
Must be nice to work on a rust free truck
@calholli
3 ай бұрын
Just move away from there.. There's a huge country down here without salt problems
Simple fix
Why does every job on the net seem easy until you try it yourself?
Me too 😂
My only question is why don't you power wash all that stuff because now you got all that dirt I'm not judging I'm just saying
Super glue
Get a car wash
@pjstpierre2340
3 ай бұрын
Maybe the “owner” will take your advice
No comment
No lube on the sway bar bushings? Squeek much?
@Admiral_Potato41
3 ай бұрын
I've honestly never lubed up the bar or bushings on any of my trucks/cars and I've never dealt with a squeak. Could be the insta-new england-rust that forms on anything immediately. Lol
@calholli
3 ай бұрын
The squeek lets you know it's still attached