Well done! One of the best step by step videos on this topic. Thank you for posting this. Update: Finished mine today. Went well but finding a 41/64th drill to ream out the push rod to the same diameter as the original one was tough. The 2011 hydro-boost that I installed in my 2006 is a big improvement on braking. But the hole on the push rod is slightly undersized. Hence the 41/64th drill. Once we got that done, it went well. Thanks again!!
@DownNDirty_OffRoad
2 жыл бұрын
Thank you!!!
@mr.nobody68
2 жыл бұрын
Thanks for the tip
@heywatsup671
2 жыл бұрын
notice any improvement in steering feel? easier to turn when stopped?
@wolfsmane
2 ай бұрын
Maybe a dumb question, can the rod be taken out and swapped? I haven't done this repair yet and was curious.
@jimsjacob
2 ай бұрын
@@wolfsmane I can't say definitively as I didn't even try, but I don't think the playoff is worth the squeeze. Seals and so forth involved I'd think. Just ream that hole out and wa-la
@MrStaybrown2 жыл бұрын
By far the best tutorial! Thanks I'll be doing my LB7
@DownNDirty_OffRoad
2 жыл бұрын
Thank you!!
@kseries20-24only Жыл бұрын
Great video! We need to also change the high pressure lines on the 04 Duramax we rescued from the auction. Fluid all over our fresh suspension job!🙃
@DownNDirty_OffRoad
Жыл бұрын
Thank you!!😃
@jamesdevore44432 жыл бұрын
The brake pedal clip was kicking my butt thanks I know the rest of the job snag thanks
@theruffhousedogs3 жыл бұрын
Perfect! Working on this now and needed to know about that clip
@120acrewood7
3 жыл бұрын
Subscribed to you from both our channels here in thanks for the information that helped us get that clip
@picwick573 жыл бұрын
FYI the studs holding the master reservoir are right hand removable & gives way more room when removing hydroboost
@DownNDirty_OffRoad
3 жыл бұрын
Good to know!!!
@Dead-Goldstar Жыл бұрын
How do you know if your hydroboost is no longer working my pedal is soft pads are good pushed the rear pistons in when doing the parking pads wonder ifI need to lead the breaks my service brake system warning message is on as well.
@DownNDirty_OffRoad
Жыл бұрын
Normal reasons for changing are it is leaking and or steering issues is why I did mine. Couldn't steer while braking.
@osvaldomoraleos22798 ай бұрын
I just replaced mine and the brake pedal vibrates when I step on it I’m thinking the air got in to the system can you can give me some info?
@DownNDirty_OffRoad
8 ай бұрын
Did you bleed it out like the video shows?
@johnadams47089 ай бұрын
Excellent job, thanks for the inf.
@DownNDirty_OffRoad
9 ай бұрын
Thank you!!
@aronsantos99667 ай бұрын
My mechanic. He helps replace Tha this weekend
@brianhopkins66572 ай бұрын
Great informative video.
@DownNDirty_OffRoad
2 ай бұрын
Thank you!!😀
@freddygonzales69992 жыл бұрын
did upgrade on my 06 duramax with 2011 hydro boost went on no problem But now no brake lights any ideas how to fix thanks
@DownNDirty_OffRoad
2 жыл бұрын
Has to been the plastic brake switch that goes on the pin for the brake peddle. I had to replace mine, but it was awhile after doing the swap. It kicks the cruise control off as well.
@freddygonzales6999
2 жыл бұрын
Thanks I’ll give it a shot 👍
@SteveHearne-oj1pm3 ай бұрын
I didn't hear you say why you were changing out the hydro boost or how to diagnose a problem with it. I have an 06 GMC dump truck and am not sure if I need a new master cylinder or a new hydro boost or both.
@DownNDirty_OffRoad
3 ай бұрын
I changed because of steering issues. When they go bad in the trucks you loose the ability to steer well while braking. It took care of the problem
@joe83193392 жыл бұрын
Thanks Buddy.
@bibektamang250510 ай бұрын
Best informative video
@DownNDirty_OffRoad
10 ай бұрын
Thank you!!🙂
@brianhopkins66572 ай бұрын
Can I use the 2011 Hydroboost for my 2006 LBZ 3500 Dually.
@DownNDirty_OffRoad
2 ай бұрын
Yes, but the hole for the brake peddle pin is slightly smaller and will need to be opened up
@brianhopkins6657
2 ай бұрын
@@DownNDirty_OffRoad What drill bit size is it to make hole larger.
@sullyduramax Жыл бұрын
changed my 03 gmc booster and it does shift out of park ok but the brakes seem like they are applied barely moves! Also the throw on the pedal is right there when you touch them with no to little play. Any ideas!
@DownNDirty_OffRoad
Жыл бұрын
Sounds like the wrong booster, or a bad one. It should have play.
@ricardoestevis66907 ай бұрын
Subscribed 🎉
@DownNDirty_OffRoad
6 ай бұрын
Thank you!!
@filibertovargas8354 Жыл бұрын
Good job did you needed to bleed the brakes with this job?
@DownNDirty_OffRoad
Жыл бұрын
I did not since nothing was done with the master cylinder.
@filibertovargas8354
Жыл бұрын
Thankyou so much
@Tyronewoodleysgrandson445 Жыл бұрын
Changed mine on a 2002 gmc any reason why it won’t shift out of park?
@DownNDirty_OffRoad
Жыл бұрын
Brake switch for sure
@jackstrawfromwitchita59786 ай бұрын
DO you drain the fluid out before starting this job?
@DownNDirty_OffRoad
6 ай бұрын
I didn't
@danielmagyari Жыл бұрын
thank you .very professional
@DownNDirty_OffRoad
Жыл бұрын
Thank you!!
@danielmagyari
Жыл бұрын
@@DownNDirty_OffRoad i gut change mine but the brake pedal is all the way down. i get pressure only when i lift up the brake pedal. I don't know what i did wrong. Can you please give me an advise
@DownNDirty_OffRoad
Жыл бұрын
@@danielmagyari Did you bleed all the air out of the system? Sounds like air.
@danielmagyari
Жыл бұрын
@@DownNDirty_OffRoad thank you for taking time to respond.i have missing the brakes rod so I took from the old one
@FansSports2 жыл бұрын
Thought I had the only 2006 Chevy Duramax LBZ CC with only one thousand miles on it.
@cesargalache2054 Жыл бұрын
What do you do if air does get in the lines pump or w.e mine is making noise I'm sure it's that and not the belt
@DownNDirty_OffRoad
Жыл бұрын
Just follow the purging procedure I did here with a hose. All of the air will blead out.
@cesargalache2054
Жыл бұрын
@@DownNDirty_OffRoad sounds good appreciate it
@MalikWong Жыл бұрын
Is it normal to have black oily dusty mudgy all over the master cylinder and underneath the turbo resonator? I have a LLY, it looks just like yours
@DownNDirty_OffRoad
Жыл бұрын
It is not. Some thing is leaking and needs repaired. Clean everything off and watch where it is coming from.
@carlitosortiz2870
10 ай бұрын
Is your power steering hard at certain times?
@lukegumm5792 Жыл бұрын
Can you show where the hydro boost was leaking from?
@DownNDirty_OffRoad
Жыл бұрын
It wasn't leaking. I changed it because of a weak pedal and hard to steer
@jeanramey6332 жыл бұрын
great video!
@DownNDirty_OffRoad
2 жыл бұрын
Thank you!!
@melthebarber88552 жыл бұрын
Thank you!
@brianholzworth72703 жыл бұрын
What size are those tires, and wheels?
@DownNDirty_OffRoad
3 жыл бұрын
33x12.5x20
@brianholzworth7270
3 жыл бұрын
@@DownNDirty_OffRoad could you also share the offset of the wheel? I have the same truck as you, and love the look
@DownNDirty_OffRoad
3 жыл бұрын
@@brianholzworth7270 I will check
@mr.nobody682 жыл бұрын
Doing a 2013 GMC 2500HD right now. Wish I didn't take the master cylinder completely off the truck. Looked like it wouldn't be far enough away
@DownNDirty_OffRoad
2 жыл бұрын
There is room and the studs connecting them unscrew as well giving more room if needed
@mr.nobody68
2 жыл бұрын
@@DownNDirty_OffRoad strongly recommend everybody out there to get an OEM boost. Aftermarket didn't have the brake push rod, spring, and star looking retaining washer. Nobody sells em separate. Broke the old star washer Went OEM Also The one I worked on, the clip on the brake pedal was a whore to remove. There's a 10mm bolt which has plastic around it where it fits into the clip. DO NOT FUCKING REMOVE THE BOLT! Doing so ruins the clip but you won't know that until you try to drive it and the fucker falls off. Lastly, there is a brake pedal position sensor way up in there that you won't see at first. In 2 miles, I couldn't get up to 40mph. Didn't understand why it threw a check engine light. The truck thought I was standing on the brakes.
@DownNDirty_OffRoad
2 жыл бұрын
@@mr.nobody68 I only buy OEM!!
@josejulianperez74253 жыл бұрын
What is the size for take off the line?
@DownNDirty_OffRoad
3 жыл бұрын
3/8 ID clear hose from Lowes. I stated that in the video.
@YourMom-zf5rt Жыл бұрын
What size flare nut wrench is that
@elviscavey4915
Жыл бұрын
I know this is late but the line on the driver side is a 15mm and the line on the passenger side is an 18mm. I managed to get away with being very careful and using the open end of my wrenches to break them loose and remove them
@jamesdevore44432 жыл бұрын
I'll come back to see how you bled the lines
@zombieskillforcoler
2 жыл бұрын
Raise the front of the vehicle only and turn the steering wheel lock to lock about 20 times it’ll get the air out. Not that hard.
@MNicehole2 жыл бұрын
Got to use the correct power steering fluid or it will take out the seal on your brake booster, just saying. happened on my 85 chevy.
Пікірлер: 80
Well done! One of the best step by step videos on this topic. Thank you for posting this. Update: Finished mine today. Went well but finding a 41/64th drill to ream out the push rod to the same diameter as the original one was tough. The 2011 hydro-boost that I installed in my 2006 is a big improvement on braking. But the hole on the push rod is slightly undersized. Hence the 41/64th drill. Once we got that done, it went well. Thanks again!!
@DownNDirty_OffRoad
2 жыл бұрын
Thank you!!!
@mr.nobody68
2 жыл бұрын
Thanks for the tip
@heywatsup671
2 жыл бұрын
notice any improvement in steering feel? easier to turn when stopped?
@wolfsmane
2 ай бұрын
Maybe a dumb question, can the rod be taken out and swapped? I haven't done this repair yet and was curious.
@jimsjacob
2 ай бұрын
@@wolfsmane I can't say definitively as I didn't even try, but I don't think the playoff is worth the squeeze. Seals and so forth involved I'd think. Just ream that hole out and wa-la
By far the best tutorial! Thanks I'll be doing my LB7
@DownNDirty_OffRoad
2 жыл бұрын
Thank you!!
Great video! We need to also change the high pressure lines on the 04 Duramax we rescued from the auction. Fluid all over our fresh suspension job!🙃
@DownNDirty_OffRoad
Жыл бұрын
Thank you!!😃
The brake pedal clip was kicking my butt thanks I know the rest of the job snag thanks
Perfect! Working on this now and needed to know about that clip
@120acrewood7
3 жыл бұрын
Subscribed to you from both our channels here in thanks for the information that helped us get that clip
FYI the studs holding the master reservoir are right hand removable & gives way more room when removing hydroboost
@DownNDirty_OffRoad
3 жыл бұрын
Good to know!!!
How do you know if your hydroboost is no longer working my pedal is soft pads are good pushed the rear pistons in when doing the parking pads wonder ifI need to lead the breaks my service brake system warning message is on as well.
@DownNDirty_OffRoad
Жыл бұрын
Normal reasons for changing are it is leaking and or steering issues is why I did mine. Couldn't steer while braking.
I just replaced mine and the brake pedal vibrates when I step on it I’m thinking the air got in to the system can you can give me some info?
@DownNDirty_OffRoad
8 ай бұрын
Did you bleed it out like the video shows?
Excellent job, thanks for the inf.
@DownNDirty_OffRoad
9 ай бұрын
Thank you!!
My mechanic. He helps replace Tha this weekend
Great informative video.
@DownNDirty_OffRoad
2 ай бұрын
Thank you!!😀
did upgrade on my 06 duramax with 2011 hydro boost went on no problem But now no brake lights any ideas how to fix thanks
@DownNDirty_OffRoad
2 жыл бұрын
Has to been the plastic brake switch that goes on the pin for the brake peddle. I had to replace mine, but it was awhile after doing the swap. It kicks the cruise control off as well.
@freddygonzales6999
2 жыл бұрын
Thanks I’ll give it a shot 👍
I didn't hear you say why you were changing out the hydro boost or how to diagnose a problem with it. I have an 06 GMC dump truck and am not sure if I need a new master cylinder or a new hydro boost or both.
@DownNDirty_OffRoad
3 ай бұрын
I changed because of steering issues. When they go bad in the trucks you loose the ability to steer well while braking. It took care of the problem
Thanks Buddy.
Best informative video
@DownNDirty_OffRoad
10 ай бұрын
Thank you!!🙂
Can I use the 2011 Hydroboost for my 2006 LBZ 3500 Dually.
@DownNDirty_OffRoad
2 ай бұрын
Yes, but the hole for the brake peddle pin is slightly smaller and will need to be opened up
@brianhopkins6657
2 ай бұрын
@@DownNDirty_OffRoad What drill bit size is it to make hole larger.
changed my 03 gmc booster and it does shift out of park ok but the brakes seem like they are applied barely moves! Also the throw on the pedal is right there when you touch them with no to little play. Any ideas!
@DownNDirty_OffRoad
Жыл бұрын
Sounds like the wrong booster, or a bad one. It should have play.
Subscribed 🎉
@DownNDirty_OffRoad
6 ай бұрын
Thank you!!
Good job did you needed to bleed the brakes with this job?
@DownNDirty_OffRoad
Жыл бұрын
I did not since nothing was done with the master cylinder.
@filibertovargas8354
Жыл бұрын
Thankyou so much
Changed mine on a 2002 gmc any reason why it won’t shift out of park?
@DownNDirty_OffRoad
Жыл бұрын
Brake switch for sure
DO you drain the fluid out before starting this job?
@DownNDirty_OffRoad
6 ай бұрын
I didn't
thank you .very professional
@DownNDirty_OffRoad
Жыл бұрын
Thank you!!
@danielmagyari
Жыл бұрын
@@DownNDirty_OffRoad i gut change mine but the brake pedal is all the way down. i get pressure only when i lift up the brake pedal. I don't know what i did wrong. Can you please give me an advise
@DownNDirty_OffRoad
Жыл бұрын
@@danielmagyari Did you bleed all the air out of the system? Sounds like air.
@danielmagyari
Жыл бұрын
@@DownNDirty_OffRoad thank you for taking time to respond.i have missing the brakes rod so I took from the old one
Thought I had the only 2006 Chevy Duramax LBZ CC with only one thousand miles on it.
What do you do if air does get in the lines pump or w.e mine is making noise I'm sure it's that and not the belt
@DownNDirty_OffRoad
Жыл бұрын
Just follow the purging procedure I did here with a hose. All of the air will blead out.
@cesargalache2054
Жыл бұрын
@@DownNDirty_OffRoad sounds good appreciate it
Is it normal to have black oily dusty mudgy all over the master cylinder and underneath the turbo resonator? I have a LLY, it looks just like yours
@DownNDirty_OffRoad
Жыл бұрын
It is not. Some thing is leaking and needs repaired. Clean everything off and watch where it is coming from.
@carlitosortiz2870
10 ай бұрын
Is your power steering hard at certain times?
Can you show where the hydro boost was leaking from?
@DownNDirty_OffRoad
Жыл бұрын
It wasn't leaking. I changed it because of a weak pedal and hard to steer
great video!
@DownNDirty_OffRoad
2 жыл бұрын
Thank you!!
Thank you!
What size are those tires, and wheels?
@DownNDirty_OffRoad
3 жыл бұрын
33x12.5x20
@brianholzworth7270
3 жыл бұрын
@@DownNDirty_OffRoad could you also share the offset of the wheel? I have the same truck as you, and love the look
@DownNDirty_OffRoad
3 жыл бұрын
@@brianholzworth7270 I will check
Doing a 2013 GMC 2500HD right now. Wish I didn't take the master cylinder completely off the truck. Looked like it wouldn't be far enough away
@DownNDirty_OffRoad
2 жыл бұрын
There is room and the studs connecting them unscrew as well giving more room if needed
@mr.nobody68
2 жыл бұрын
@@DownNDirty_OffRoad strongly recommend everybody out there to get an OEM boost. Aftermarket didn't have the brake push rod, spring, and star looking retaining washer. Nobody sells em separate. Broke the old star washer Went OEM Also The one I worked on, the clip on the brake pedal was a whore to remove. There's a 10mm bolt which has plastic around it where it fits into the clip. DO NOT FUCKING REMOVE THE BOLT! Doing so ruins the clip but you won't know that until you try to drive it and the fucker falls off. Lastly, there is a brake pedal position sensor way up in there that you won't see at first. In 2 miles, I couldn't get up to 40mph. Didn't understand why it threw a check engine light. The truck thought I was standing on the brakes.
@DownNDirty_OffRoad
2 жыл бұрын
@@mr.nobody68 I only buy OEM!!
What is the size for take off the line?
@DownNDirty_OffRoad
3 жыл бұрын
3/8 ID clear hose from Lowes. I stated that in the video.
What size flare nut wrench is that
@elviscavey4915
Жыл бұрын
I know this is late but the line on the driver side is a 15mm and the line on the passenger side is an 18mm. I managed to get away with being very careful and using the open end of my wrenches to break them loose and remove them
I'll come back to see how you bled the lines
@zombieskillforcoler
2 жыл бұрын
Raise the front of the vehicle only and turn the steering wheel lock to lock about 20 times it’ll get the air out. Not that hard.
Got to use the correct power steering fluid or it will take out the seal on your brake booster, just saying. happened on my 85 chevy.