Cheap and easy H3 hummer lift
Автокөліктер мен көлік құралдары
H3 Hummer lift kit !
With no H3 Hummer lift kits available anymore. Here I will show you how to lift your H3 well past the 23.5” limit cost effectively without the risk of blowing CV’s
With Rancho dropping the support and supply of the 4 inch lift kit there aren’t a lot of options available for off the shelf lifts.
Torsion key lift kits marketed as a viable lift can be an absolute waste of money if you are only intending to lift to the factory maximum of 23.5 inches measured from centre of hub to under the fender opening.
This limit is due to the maximum amount of angle the CV joints are capable of running.
The factory lift keys are more then capable of lifting to this limit. So many will that you have wasted your money if you bought a lift key setup. While this is true if only going to factory hight they do in fact have a use when you want to go higher than what the factory torsion keys allow you to crank. To go past the factory limit you will need to correct the CV drive shaft angles. I will show you how to do that and allow you to lift your H3 Hummer past the factory limit.
Пікірлер: 19
Thanks!
@hsvh3hummer942
2 жыл бұрын
My pleasure. Hope it was helpful
Great video, thanks. Would you know if one can fit 37in tires on a (zero offset) 18x9in rim with the 38mm diff drop and 1in body lift? I guess for many of us the goal of that whole exercise will be 37s.
@hsvh3hummer942
6 ай бұрын
Yes with the addition of a body lift it has been done successfully.
What exactly do you mean when you say "TOP" ? Are you talking about where the differential mounts to the transfer case? Or "FRONT 2 MOUNTS?
@hsvh3hummer942
Жыл бұрын
Front two mounts
Great post! !! How many centimeters is the spacer?
@hsvh3hummer942
2 жыл бұрын
3.8cm
What was done for the rear diff bushing and was there any adverse effects on the tierod angles?
@hsvh3hummer942
Жыл бұрын
Tie rod ends do run at a higher angle but not so much as they effect steering. Simple tie rod spacers are available online to correct the angles but I have never tried them. Not sure what you mean about the rear differential bushings as there was no need to change them unless worn.
Can u put a 6 inch lift on a h3 ?
So to clearify you didn't show the front diff Mount, but both the front and rear can be dropped about 1.5in or (32mm)?
@hsvh3hummer942
Жыл бұрын
Hi mate. The h3 has a mount either side as seen in the pictures that you need to space down. The 3rd mounting point is under the differential pumpkin to the cross members which is spaced down using four plates to lower the cross member Hope that clears it up for you.
Do you have a spacer kit for sale? Thanks for the vid post.
@hsvh3hummer942
2 жыл бұрын
Hi Blake. I don’t sell the kit. Being based in Australia with most of the Market being overseas the shipping makes it not viable. It’s is a simple enough kit to put together from local hardware suppliers in your area. Or if you showed this video to any decent mechanic they could do it for you.
@beurownboss1554
Жыл бұрын
Check out this one, its what I just ordered. www.badlandindustries.com/product-page/differential-drop-05-10-h3-h3t
@SystemCrasher113
Жыл бұрын
kzread.info/dash/bejne/oaKLuJp9dKa7lJs.html
Hi! How can you see the drawings?
@hsvh3hummer942
Жыл бұрын
Sorry no drawings available