Everyone chill😂 I JUST bought the jeep, had no idea about their weird oil filters. I am not a expert just a diyer man! This thing is diff then every other vehicle I own
@cyrusmakowski1644
Жыл бұрын
Try to return it, jeeps are garbage
@coyotearmory
Жыл бұрын
Something to note, check on that O-ring in the housing every few oil changes, they do leak over time and it's a cheap and easy part to fix
@cyrusmakowski1644
Жыл бұрын
@@coyotearmory i believe you have to change it every time
@OHHyaKnow
Жыл бұрын
Don’t diy if you don’t know what you’re doing.
@cyrusmakowski1644
Жыл бұрын
@@OHHyaKnow that and don't make videos "teaching" other people
@OneWayMX38 Жыл бұрын
Inflation is crazy so taking you vehicle gets expensive so your better off doing it yourself! Have a good day everyone, stay safe!
@oye6124
Жыл бұрын
you were always better off doing it yourself
@OneWayMX38
Жыл бұрын
@@oye6124 100%
@foojub6907
Жыл бұрын
@@oye6124always? You see dumb shit on the regular in a workplace “trained” environment… now imagine someone with no experience or supervision…yeah
@austingutierrez2709
Жыл бұрын
It’s like 120+ for a full synthetic at my local pip boys, jiffy lube and valvalean…thank god I barely pay 50$ doin it myself 💀
@bryanmercado8755
Жыл бұрын
Pretty sure it’s always that way
@court5975 Жыл бұрын
Check your oil cooler they always leak. It will run down the top of the bell housing if its bad enough. Jeeps make me alot of money 🤑👩🏻🔧 love the content.
@UltraMagaFan
Жыл бұрын
No wonder your making money off of them. Jeeps are complete junk. I saw a video of one, I can’t remember what model, that had plastic throttle body, plastic intake, plastic valve covers, and a plastic oil pan. There’s way too much plastic in those engines.
@OhCorny
Жыл бұрын
It’s not difficult to replace but it’s a daunting task. If you see oil dripping between the inspection holes of the trans it’s 90% the oil cooler or someone left oil in the valley of the v6 when you accelerate it will slosh back and look very similar to a bad rear main seal
@user-white007
Жыл бұрын
@@UltraMagaFan3.6 is junk but it’s not the plastics fault. Every modern car has switched to durable high temp plastics for a lot of things cause it’s totally okay for some things
@UltraMagaFan
Жыл бұрын
@@user-white007 Plastic isn’t durable. It warps over time and causes oil leaks. Plastic oil pans and plastic valve covers are known to fail prematurely.
@Dane-bootsNcatsN
Жыл бұрын
Yes ive just done this job on my grand caravan. Easy enough except for trying to get all the oil out the valley after removing the housing. That took me longer than actually replacing the part
@leonardocalvillo7029 Жыл бұрын
Two things not mentioned in this video, make sure you replace the o-ring on the oil filter cap, and don’t check your dipstick the first time you take it out, pull it out, wipe it clean, put the dipstick back in then pull it back out for an accurate reading
@user-vw4cg1xq7r
Жыл бұрын
Pre fill some oil in the filter too if you can
@jessepickar3297
Жыл бұрын
That’s true but you wanna start the engine before so it pressurizes the filter and gives you an accurate reading.
@stephm0
Жыл бұрын
Also lubricate the new o-ring with some oil before installing. Also replace the washer on the drain plug
@TravelogsIndia
Жыл бұрын
Yeah correct bro..
@RGV2300 Жыл бұрын
That thing gotta be really tall to be able to put that bucket beneath.
@dominicekezie2011
4 ай бұрын
This is the comment you decided to leave
@ChillyJD26 Жыл бұрын
make sure to change your oil filter canister seals too!
@blakexie5209
Жыл бұрын
Was gonna say the same thing
@THE_GOLDEN_JET
Жыл бұрын
Just called a o ring
@ryanallen5334
Жыл бұрын
It's not a cannister. It's a cartridge. A cannister is an old style metal oil filter that looks like a CAN. Lol
@zsteppin8249
Жыл бұрын
@@ryanallen5334 metal ones the you replace are called spin ons
@drcannibalclown7497
Жыл бұрын
looks similar to some bmw oil filters designed similar
@joshbanuelos6441 Жыл бұрын
It’s actually a 13mm, works at the Chrysler dealership for a while
@cyrusmakowski1644
Жыл бұрын
13mm fits but technically it is supposed to b 1/2in. American vehicle, American sizes. 13mm tends to strip those plugs. Whenever I do these I swap the plug for a 16mm head with the same thread/gasket so they don't strip.
@chexlemeneux8790
Жыл бұрын
@Cyrus Makowski Not a single imperial bolt on it. They are all metric.
@theyoungrob7151
Жыл бұрын
When you tell the tech and he’s like no it’s not but we’ve been working for years wtf do we know lol
@cyrusmakowski1644
Жыл бұрын
Really? I honestly assumed it was supposed to be SAE because of how often those garbage plugs strip with a 13. Poorly designed like the rest of the vehicle I suppose 🤣
@7kzone
Жыл бұрын
Can you guys please make a god damn vehicle that makes it over 13k miles?
@paulherrington5837 Жыл бұрын
Always be sure to not over tighten the oil filter housing cap when reinstalling it. The plastic housing is usually brittle from heating and cooling cycles and crack very easily leaving you with a oil leak and a days worth of work to replace the oil cooler 😂
@obslegend674
Жыл бұрын
Yessir 25nm only
@richbrown8174
Жыл бұрын
A good investment would be a torque wrench think the oil filter housing might be 25Nm or wherever in Imperial it may say on the housing 🤔 You can also torque the sump plug correctly too 😉
@kevindunn175 Жыл бұрын
I like your style as a kid growing up ( I’m 38 ) watching my dad cut a 2 liter soda bottle in half and using it as a funnel this too me back to nostalgialand!
@frost-bittenpunk2019 Жыл бұрын
Make sure you follow torque specs. 18-19 foot pounds for the filter, 20 for the oil pan drain plug.
@1customermaniac Жыл бұрын
Man, you made that look so easy. Appreciate the chill approach to it. Looking forward to more!
@will_mcdermott4 ай бұрын
You’re the first dude I’ve ever seen who looks like you
@zoranmaricic7679 Жыл бұрын
Well, fogot to take the oil cap off at the beginning. Also forgot to put the replacement gasket on the filter housing/cap
@bushkangarutha7849
Жыл бұрын
And the copper washer/Teflon/sealant on the sump plug
@michaelscott2481 Жыл бұрын
You just have such a contagious positive energy. Love it
@ethanbrush2089 Жыл бұрын
Man forgot to replace the rubber seal ring on the filter
@marswrld2489 Жыл бұрын
Yea honestly you save so much more money when you do it yourself plus you don’t have to worry about someone rounding out your drain bolt or stripping the threads😭
@badazz2969 Жыл бұрын
no cars after 99 have standard bolts or nuts its all metric now and never use 12 point sockets bad things happen only use them on 12 point bolts
@JellyeatsJams Жыл бұрын
Colorado native here welcome brotha
@MikeClowder Жыл бұрын
When changing the oil filter, make sure to change the o ring on the filter cap as well.
@tristonmurdock609 Жыл бұрын
that funnel adds 12 horsepower guaranteed
@06wrx_ Жыл бұрын
Only thing i’d add, if your doing it on a different vehicle with the filter mounted on the bottom, Make sure you pour oil into it and on the lip before install.
@Smithson52 Жыл бұрын
Wow i had no idea Jeep moved the filter to the top, much more convenient.
@Pedro-ke6xp Жыл бұрын
You didnt mention it but remember to change the crush washer in the oil pan and the seals on the oil filter housing
@Devo1987 Жыл бұрын
im geting a saved by the bell vibe here
@coltonmullins2274 Жыл бұрын
Welcome to CO man! Where did you end up settling?
@TheSuperaaron219 Жыл бұрын
Crustier 3.6 liter pay attention to oil leaks around the transmission that oil filter and oil cooler housing are just plastic over time they crack and cause a huge oil leak the requires a fair amount of work to fix. Also never forget to lube that o ring in the filter housing you can just use old oil or new works too if your bougie like that.
@benjamindabson7592 Жыл бұрын
I hope you changed the oil filter o rings as well
@gradyflinn6765 Жыл бұрын
helps to have the fill cap open before draining too
@51-FS Жыл бұрын
Oil drain is a 13mm
@mikeirwin5891
Жыл бұрын
Negative it’s a 1/2 you’ll eventually round out the drain plug if you use a 13.
@51-FS
Жыл бұрын
@@mikeirwin5891shows that you don't know what your talking about......
@51-FS
Жыл бұрын
It's a 13. If you use a 1/2 inch you will round out the bolt over time? Like you did in your dodge
@51-FS
Жыл бұрын
Lol pay attention to the socket he used to tighten the drain bolt... its not the 1/2 he used to take it off.... he probably switched to the right size because it was rounding off when he tightened it....
@southernseth449 Жыл бұрын
I would recommend getting a torque wrench and look up the torque specs for the drain plug. I work in an oil change shop and I can’t tell you how many people do their own oil change and then overtorque the drain plug and blow the threads out. For your keep it should be 20 or 25 ft pounds but that’s just my recommendation.
@gubbtratt1
Жыл бұрын
Nah, tighten it until it starts going easy and then a half revolution back.
@merrickbiondolillo7961 Жыл бұрын
What happened to the wagoneer?
@Matrix-_-404 Жыл бұрын
This guy is every dads dream son,
@liamreid Жыл бұрын
Grand wagoneer should be back from pain this month!
@silvercar07
Жыл бұрын
back from p a i n
@lilbossking4869
Жыл бұрын
that things gunna be minty👍👍
@kasmith_ Жыл бұрын
Drain plug is a 13mm, not a 1/2, and yes, overtime it makes a difference
@OfficialNakatsuMegami Жыл бұрын
Nothing like seeing a collapsed oil filter when you pop it out.
@hugomuxic7043 Жыл бұрын
Forgot to unscrew oil cap first. That oil cap vacuum prevents proper draining.
@blueblaze9800 Жыл бұрын
I use to work at a oil shop and I recommend not to go to one these days since their expensive and they at times will scam you and on the other hand the people working downstairs may use power tools for your drain plug so please try not to take your vehicle there too often
@mxtrend114 Жыл бұрын
Everybody should change their own well it’s a rip off to go take it to the mechanic
@OneWayMX38
Жыл бұрын
For sure with inflation as well
@guesswho36
Жыл бұрын
Yea so let all the mechanics become jobless!
@andrewferguson9478
Жыл бұрын
The reason you take it to a mechanic to do. It is because they usually do a general inspection of the vehicle and let you know if anything else is bad
@foojub6907
Жыл бұрын
@@andrewferguson9478they ain’t inspecting shit unless you ask or it’s blatantly obvious
@foojub6907
Жыл бұрын
@@BlackLung87 Most are like that is the point.
@CaydenSavitch-pq5vu Жыл бұрын
No one is talking about the wagoner?
@coyoterob2839 Жыл бұрын
Where do u take /dump the oil at?
@dportwz2280 Жыл бұрын
I usually turn my truck on while its drainning it helps getting all the oil out
@macse7en
Жыл бұрын
please tell me you’re not serious lmfao
@bushkangarutha7849
Жыл бұрын
I do this but make sure it's on redline and drain the coolant at the same time. Works great!
@new_simsons
Жыл бұрын
I usually drive my car really hard until the head gasket blows up. Now the only thing to do is replace it, replace the oil filter and put oil. Really useful!
@dportwz2280
Жыл бұрын
@@new_simsons nice 🤙🏼
@dportwz2280
Жыл бұрын
@@bushkangarutha7849 heck yeah! This is another great option
@pearbearhd4737 Жыл бұрын
The only jeep owner that does their own oil change
@rickkrnjaic4806
Жыл бұрын
This comment isn’t being showed enough love 😂😂
@pearbearhd4737
Жыл бұрын
@@rickkrnjaic4806 thank you bro 😂 it’s probably my name
@pearbearhd4737
Жыл бұрын
@@Tensentities I don’t really care that much bro
@jonathanshiflett8877 Жыл бұрын
Just make sure to always replace the O-ring on those types of oil filters and lube it before installing it to prevent O-ring failure, also always start the engine after putting the oil in and then turn off the engine let it sit for about a minute and then check the oil level. Otherwise great video. Also don’t forget to replace the crush washer on the drain plug if your car has one to prevent leaks, this car doesn’t it uses a rubber seal but still always replace the crush washer when needed. One last important tip always run the correct oil for your engine to prevent long term damage.
@eddominiczak669 Жыл бұрын
No new washer or O-ring, nice to see he installed the self lubricating chassis system
@cookingwithellett Жыл бұрын
love the shirt!
@itz.Lutendo Жыл бұрын
Bro looks like John cena
@johnjohnfofohniam Жыл бұрын
I know I've been exposed to too much of the Mineblock when I heard "creeper." 😂😂 Thanks, daughter.
@arnavsharma6657 Жыл бұрын
hey man, making the oil filter wet in the engine oil before fitting it in is recommended.
@kodybardot9827 Жыл бұрын
Do you drink a lot of coolrs because your bike got a coolrs can for the rear shock and now a funnel😂
@toiletgaming2005 Жыл бұрын
with cartridge style oil filters you ALWAYS unscrew the filter housing before the sump plug so it lets the oil drain down into the oilpan or youll be left with half a quart of dirty oil if you dont believe me leave the sump plug off and crack the filter loose 👍
@SketchyWhiteBoy Жыл бұрын
No new o ring on the filter housing?
@theactualdarthvader Жыл бұрын
don’t forget the replace and lube the o ring seal on the filter housing
@2thgun Жыл бұрын
That drain was smooth tho man props
@CorbinOutdoors Жыл бұрын
Good to know 👍
@Silveradoss Жыл бұрын
1/2 socket on an American made vehicle makes sense get a 13mm do it right
@WattsGemini323 Жыл бұрын
I recommend taking a trip down to your local autoparts and pick up a honda pilot or odyssey oil drain plug/bolt Same thread pitch but you can use a 17mm instead of 13mm i was a lube tech 4 years
@JerraredTheTard Жыл бұрын
Does it have the 3.8 or the 3.6? And is it the 6 speed or the auto? I had the 6speed blew at 120k miles with routine maintenance.. putting a 5.3 and an 8 speed in my 09 2 door now since It was gonna cost the same to do the swapp then to get a refurbished one..
@roofcamper3473
Жыл бұрын
Chrysler moment
@andrewandrew4791 Жыл бұрын
That house looks like the KZreadrs house that had that slammed out corvette
@tribbs79 Жыл бұрын
Always remember to change the rubber piece on the oil filter and lube is too
@ryanrobbins25796 ай бұрын
And here I am fighting my liberty’s oil filter
@The333Wanderer Жыл бұрын
After the oil change, run the engine for five minutes. Then check for leaks. Then check the oil level again-that’s after about five to ten minutes without the engine running.
@danielkingery2894 Жыл бұрын
So glad that wasn't a janky Bud Light funnel.👍
@nolankostka Жыл бұрын
Not replacing that O-Ring is making my OCD flare
@benjaminabel8596 Жыл бұрын
Hey that Valvoline Advanced was on clearance at Autozone. $20/5qts.
@phoenixproductions5358 Жыл бұрын
It’s a 13mm not half inch, make sure you also change gasket on filter cup and don’t over tight or else you’ll crack the housing
@sagethemage7 Жыл бұрын
When you're drawing the oil, Crack open the oil filter cap, more oil will fall through from pressure.
@panchoelquededejaelculoanc3512 Жыл бұрын
Its a 13 mm
@BikerBenny Жыл бұрын
Colorado must have epic enduro spots! 😀😀 i need to move 😭😭
@alexk4661 Жыл бұрын
should’ve included instructions on the o-ring unless you forgot. Very VERY critical part.
@jasonsharpbucks Жыл бұрын
not having to jack it up or even pull out ramps is nice
@amerlin388 Жыл бұрын
Cutting down an empty 1-quart oil bottle also makes a good funnel and it will hold the quart you're pouring if you want to let it thoroughly drip empty.
@archuleta1000 Жыл бұрын
Quick tip you always wanna takeoff your oil cap first because if you can’t get it off the drain all the oil out you’re screwed has it happened once or twice not good
@BoDiggity69 Жыл бұрын
You have to start it before you check the level so it gets in the filter and pump
@ajpino1627 Жыл бұрын
In what town do you live in Colorado?
@Max-Fabs.247 Жыл бұрын
Now that you’re out in Colorado maybe we could go riding man!
@andybee4236 Жыл бұрын
Check the oil after running it and letting it stand. Oil filters keep some oil, less in this type, than canisters.
@jefflong1839 Жыл бұрын
No criticism, just curious because i've never had a vehicle with an inverted filter. Will it take a portion of the oil to fill it like a standard filter?
@mikepettit4822 Жыл бұрын
don't forget to change the o ring on the filter housing
@VastSpy031 Жыл бұрын
The classic beer can or water bottle funnel. I’ve used a plastic file rolled up super tight and with duck tape. 😂😂😂 worked great
@ngarmy6602 Жыл бұрын
Time to shine ❤️👏👍💪🔥
@kevinhamlett1400 Жыл бұрын
I would replace the oil filter housing with the metal one.
@kashi94479 күн бұрын
I recommend starting it wait 5-10 mins to get best reading
@daisydodge8536 Жыл бұрын
its a 13 mil drain plug and he didnt replace the O-ring on the canister. dont listen to this guy
@alexwyatt7800 Жыл бұрын
Oil change required? Required for what?
@Alex-nq3hw Жыл бұрын
What happened to the jeep series
@zacharyrodriguez8795 Жыл бұрын
You forgot to change out the O ring for the oil filter
@prototype_0xD1 Жыл бұрын
That's that Mercedes/ BMW oil filter housing type. Careful about torquing on it. It can crack.
@Landon_N Жыл бұрын
Replace the crush washer on the plug in addition to the oil filter o ring
@tensebro1 Жыл бұрын
It would help it drain better if you remove the oil cap and dip stick
@scotthummel4248 Жыл бұрын
2 things 1) don't forget to replace the oring on the filter lid. And 2) don't use a bud lite can, your jeep will run funny afterwards
@TheFatNinja21 Жыл бұрын
I ran to to the comments after he didn’t say to replace the seals on the filter housing
@lioneljasondsouza767 Жыл бұрын
Remember u should always lubricate the new oil ring in the drain plug if ur putting a new one and u should lubricate with the oil for the top of the oil filter
@mimis-accessories Жыл бұрын
Try pressing the Unlock Button twice then lock then unlock again. The Jeep will do a light show for you, but remember that you’ll have to do this simultaneously. This only works with Dodge, Jeep, and RAM vehicles Plz try it and make a vid about it… I subscribed already
@Noah_McLain Жыл бұрын
Where do you get rid of the oil?
@jaywattman199 Жыл бұрын
I'd loosen the oil filter first then drain. By the time it's done draining the filter won't make such a mess
@BBQandStreetCars Жыл бұрын
Screech from saved by the bell forgot to replace the oil filter housing o-ring
@jessesward9429 Жыл бұрын
Next video: “how to change the oil cooler and thermostat on your keep wrangler”
@xx_knobitv_xx5378 Жыл бұрын
Did you change the washer at your drainbolt?
@thomasdonachy6407 Жыл бұрын
You forgot to replace the gasket on the oil filter.
@obslegend674 Жыл бұрын
You forgot to start check it and verify there's no leaks at the plug or filter sir
Пікірлер: 536
Everyone chill😂 I JUST bought the jeep, had no idea about their weird oil filters. I am not a expert just a diyer man! This thing is diff then every other vehicle I own
@cyrusmakowski1644
Жыл бұрын
Try to return it, jeeps are garbage
@coyotearmory
Жыл бұрын
Something to note, check on that O-ring in the housing every few oil changes, they do leak over time and it's a cheap and easy part to fix
@cyrusmakowski1644
Жыл бұрын
@@coyotearmory i believe you have to change it every time
@OHHyaKnow
Жыл бұрын
Don’t diy if you don’t know what you’re doing.
@cyrusmakowski1644
Жыл бұрын
@@OHHyaKnow that and don't make videos "teaching" other people
Inflation is crazy so taking you vehicle gets expensive so your better off doing it yourself! Have a good day everyone, stay safe!
@oye6124
Жыл бұрын
you were always better off doing it yourself
@OneWayMX38
Жыл бұрын
@@oye6124 100%
@foojub6907
Жыл бұрын
@@oye6124always? You see dumb shit on the regular in a workplace “trained” environment… now imagine someone with no experience or supervision…yeah
@austingutierrez2709
Жыл бұрын
It’s like 120+ for a full synthetic at my local pip boys, jiffy lube and valvalean…thank god I barely pay 50$ doin it myself 💀
@bryanmercado8755
Жыл бұрын
Pretty sure it’s always that way
Check your oil cooler they always leak. It will run down the top of the bell housing if its bad enough. Jeeps make me alot of money 🤑👩🏻🔧 love the content.
@UltraMagaFan
Жыл бұрын
No wonder your making money off of them. Jeeps are complete junk. I saw a video of one, I can’t remember what model, that had plastic throttle body, plastic intake, plastic valve covers, and a plastic oil pan. There’s way too much plastic in those engines.
@OhCorny
Жыл бұрын
It’s not difficult to replace but it’s a daunting task. If you see oil dripping between the inspection holes of the trans it’s 90% the oil cooler or someone left oil in the valley of the v6 when you accelerate it will slosh back and look very similar to a bad rear main seal
@user-white007
Жыл бұрын
@@UltraMagaFan3.6 is junk but it’s not the plastics fault. Every modern car has switched to durable high temp plastics for a lot of things cause it’s totally okay for some things
@UltraMagaFan
Жыл бұрын
@@user-white007 Plastic isn’t durable. It warps over time and causes oil leaks. Plastic oil pans and plastic valve covers are known to fail prematurely.
@Dane-bootsNcatsN
Жыл бұрын
Yes ive just done this job on my grand caravan. Easy enough except for trying to get all the oil out the valley after removing the housing. That took me longer than actually replacing the part
Two things not mentioned in this video, make sure you replace the o-ring on the oil filter cap, and don’t check your dipstick the first time you take it out, pull it out, wipe it clean, put the dipstick back in then pull it back out for an accurate reading
@user-vw4cg1xq7r
Жыл бұрын
Pre fill some oil in the filter too if you can
@jessepickar3297
Жыл бұрын
That’s true but you wanna start the engine before so it pressurizes the filter and gives you an accurate reading.
@stephm0
Жыл бұрын
Also lubricate the new o-ring with some oil before installing. Also replace the washer on the drain plug
@TravelogsIndia
Жыл бұрын
Yeah correct bro..
That thing gotta be really tall to be able to put that bucket beneath.
@dominicekezie2011
4 ай бұрын
This is the comment you decided to leave
make sure to change your oil filter canister seals too!
@blakexie5209
Жыл бұрын
Was gonna say the same thing
@THE_GOLDEN_JET
Жыл бұрын
Just called a o ring
@ryanallen5334
Жыл бұрын
It's not a cannister. It's a cartridge. A cannister is an old style metal oil filter that looks like a CAN. Lol
@zsteppin8249
Жыл бұрын
@@ryanallen5334 metal ones the you replace are called spin ons
@drcannibalclown7497
Жыл бұрын
looks similar to some bmw oil filters designed similar
It’s actually a 13mm, works at the Chrysler dealership for a while
@cyrusmakowski1644
Жыл бұрын
13mm fits but technically it is supposed to b 1/2in. American vehicle, American sizes. 13mm tends to strip those plugs. Whenever I do these I swap the plug for a 16mm head with the same thread/gasket so they don't strip.
@chexlemeneux8790
Жыл бұрын
@Cyrus Makowski Not a single imperial bolt on it. They are all metric.
@theyoungrob7151
Жыл бұрын
When you tell the tech and he’s like no it’s not but we’ve been working for years wtf do we know lol
@cyrusmakowski1644
Жыл бұрын
Really? I honestly assumed it was supposed to be SAE because of how often those garbage plugs strip with a 13. Poorly designed like the rest of the vehicle I suppose 🤣
@7kzone
Жыл бұрын
Can you guys please make a god damn vehicle that makes it over 13k miles?
Always be sure to not over tighten the oil filter housing cap when reinstalling it. The plastic housing is usually brittle from heating and cooling cycles and crack very easily leaving you with a oil leak and a days worth of work to replace the oil cooler 😂
@obslegend674
Жыл бұрын
Yessir 25nm only
@richbrown8174
Жыл бұрын
A good investment would be a torque wrench think the oil filter housing might be 25Nm or wherever in Imperial it may say on the housing 🤔 You can also torque the sump plug correctly too 😉
I like your style as a kid growing up ( I’m 38 ) watching my dad cut a 2 liter soda bottle in half and using it as a funnel this too me back to nostalgialand!
Make sure you follow torque specs. 18-19 foot pounds for the filter, 20 for the oil pan drain plug.
Man, you made that look so easy. Appreciate the chill approach to it. Looking forward to more!
You’re the first dude I’ve ever seen who looks like you
Well, fogot to take the oil cap off at the beginning. Also forgot to put the replacement gasket on the filter housing/cap
@bushkangarutha7849
Жыл бұрын
And the copper washer/Teflon/sealant on the sump plug
You just have such a contagious positive energy. Love it
Man forgot to replace the rubber seal ring on the filter
Yea honestly you save so much more money when you do it yourself plus you don’t have to worry about someone rounding out your drain bolt or stripping the threads😭
no cars after 99 have standard bolts or nuts its all metric now and never use 12 point sockets bad things happen only use them on 12 point bolts
Colorado native here welcome brotha
When changing the oil filter, make sure to change the o ring on the filter cap as well.
that funnel adds 12 horsepower guaranteed
Only thing i’d add, if your doing it on a different vehicle with the filter mounted on the bottom, Make sure you pour oil into it and on the lip before install.
Wow i had no idea Jeep moved the filter to the top, much more convenient.
You didnt mention it but remember to change the crush washer in the oil pan and the seals on the oil filter housing
im geting a saved by the bell vibe here
Welcome to CO man! Where did you end up settling?
Crustier 3.6 liter pay attention to oil leaks around the transmission that oil filter and oil cooler housing are just plastic over time they crack and cause a huge oil leak the requires a fair amount of work to fix. Also never forget to lube that o ring in the filter housing you can just use old oil or new works too if your bougie like that.
I hope you changed the oil filter o rings as well
helps to have the fill cap open before draining too
Oil drain is a 13mm
@mikeirwin5891
Жыл бұрын
Negative it’s a 1/2 you’ll eventually round out the drain plug if you use a 13.
@51-FS
Жыл бұрын
@@mikeirwin5891shows that you don't know what your talking about......
@51-FS
Жыл бұрын
It's a 13. If you use a 1/2 inch you will round out the bolt over time? Like you did in your dodge
@51-FS
Жыл бұрын
Lol pay attention to the socket he used to tighten the drain bolt... its not the 1/2 he used to take it off.... he probably switched to the right size because it was rounding off when he tightened it....
I would recommend getting a torque wrench and look up the torque specs for the drain plug. I work in an oil change shop and I can’t tell you how many people do their own oil change and then overtorque the drain plug and blow the threads out. For your keep it should be 20 or 25 ft pounds but that’s just my recommendation.
@gubbtratt1
Жыл бұрын
Nah, tighten it until it starts going easy and then a half revolution back.
What happened to the wagoneer?
This guy is every dads dream son,
Grand wagoneer should be back from pain this month!
@silvercar07
Жыл бұрын
back from p a i n
@lilbossking4869
Жыл бұрын
that things gunna be minty👍👍
Drain plug is a 13mm, not a 1/2, and yes, overtime it makes a difference
Nothing like seeing a collapsed oil filter when you pop it out.
Forgot to unscrew oil cap first. That oil cap vacuum prevents proper draining.
I use to work at a oil shop and I recommend not to go to one these days since their expensive and they at times will scam you and on the other hand the people working downstairs may use power tools for your drain plug so please try not to take your vehicle there too often
Everybody should change their own well it’s a rip off to go take it to the mechanic
@OneWayMX38
Жыл бұрын
For sure with inflation as well
@guesswho36
Жыл бұрын
Yea so let all the mechanics become jobless!
@andrewferguson9478
Жыл бұрын
The reason you take it to a mechanic to do. It is because they usually do a general inspection of the vehicle and let you know if anything else is bad
@foojub6907
Жыл бұрын
@@andrewferguson9478they ain’t inspecting shit unless you ask or it’s blatantly obvious
@foojub6907
Жыл бұрын
@@BlackLung87 Most are like that is the point.
No one is talking about the wagoner?
Where do u take /dump the oil at?
I usually turn my truck on while its drainning it helps getting all the oil out
@macse7en
Жыл бұрын
please tell me you’re not serious lmfao
@bushkangarutha7849
Жыл бұрын
I do this but make sure it's on redline and drain the coolant at the same time. Works great!
@new_simsons
Жыл бұрын
I usually drive my car really hard until the head gasket blows up. Now the only thing to do is replace it, replace the oil filter and put oil. Really useful!
@dportwz2280
Жыл бұрын
@@new_simsons nice 🤙🏼
@dportwz2280
Жыл бұрын
@@bushkangarutha7849 heck yeah! This is another great option
The only jeep owner that does their own oil change
@rickkrnjaic4806
Жыл бұрын
This comment isn’t being showed enough love 😂😂
@pearbearhd4737
Жыл бұрын
@@rickkrnjaic4806 thank you bro 😂 it’s probably my name
@pearbearhd4737
Жыл бұрын
@@Tensentities I don’t really care that much bro
Just make sure to always replace the O-ring on those types of oil filters and lube it before installing it to prevent O-ring failure, also always start the engine after putting the oil in and then turn off the engine let it sit for about a minute and then check the oil level. Otherwise great video. Also don’t forget to replace the crush washer on the drain plug if your car has one to prevent leaks, this car doesn’t it uses a rubber seal but still always replace the crush washer when needed. One last important tip always run the correct oil for your engine to prevent long term damage.
No new washer or O-ring, nice to see he installed the self lubricating chassis system
love the shirt!
Bro looks like John cena
I know I've been exposed to too much of the Mineblock when I heard "creeper." 😂😂 Thanks, daughter.
hey man, making the oil filter wet in the engine oil before fitting it in is recommended.
Do you drink a lot of coolrs because your bike got a coolrs can for the rear shock and now a funnel😂
with cartridge style oil filters you ALWAYS unscrew the filter housing before the sump plug so it lets the oil drain down into the oilpan or youll be left with half a quart of dirty oil if you dont believe me leave the sump plug off and crack the filter loose 👍
No new o ring on the filter housing?
don’t forget the replace and lube the o ring seal on the filter housing
That drain was smooth tho man props
Good to know 👍
1/2 socket on an American made vehicle makes sense get a 13mm do it right
I recommend taking a trip down to your local autoparts and pick up a honda pilot or odyssey oil drain plug/bolt Same thread pitch but you can use a 17mm instead of 13mm i was a lube tech 4 years
Does it have the 3.8 or the 3.6? And is it the 6 speed or the auto? I had the 6speed blew at 120k miles with routine maintenance.. putting a 5.3 and an 8 speed in my 09 2 door now since It was gonna cost the same to do the swapp then to get a refurbished one..
@roofcamper3473
Жыл бұрын
Chrysler moment
That house looks like the KZreadrs house that had that slammed out corvette
Always remember to change the rubber piece on the oil filter and lube is too
And here I am fighting my liberty’s oil filter
After the oil change, run the engine for five minutes. Then check for leaks. Then check the oil level again-that’s after about five to ten minutes without the engine running.
So glad that wasn't a janky Bud Light funnel.👍
Not replacing that O-Ring is making my OCD flare
Hey that Valvoline Advanced was on clearance at Autozone. $20/5qts.
It’s a 13mm not half inch, make sure you also change gasket on filter cup and don’t over tight or else you’ll crack the housing
When you're drawing the oil, Crack open the oil filter cap, more oil will fall through from pressure.
Its a 13 mm
Colorado must have epic enduro spots! 😀😀 i need to move 😭😭
should’ve included instructions on the o-ring unless you forgot. Very VERY critical part.
not having to jack it up or even pull out ramps is nice
Cutting down an empty 1-quart oil bottle also makes a good funnel and it will hold the quart you're pouring if you want to let it thoroughly drip empty.
Quick tip you always wanna takeoff your oil cap first because if you can’t get it off the drain all the oil out you’re screwed has it happened once or twice not good
You have to start it before you check the level so it gets in the filter and pump
In what town do you live in Colorado?
Now that you’re out in Colorado maybe we could go riding man!
Check the oil after running it and letting it stand. Oil filters keep some oil, less in this type, than canisters.
No criticism, just curious because i've never had a vehicle with an inverted filter. Will it take a portion of the oil to fill it like a standard filter?
don't forget to change the o ring on the filter housing
The classic beer can or water bottle funnel. I’ve used a plastic file rolled up super tight and with duck tape. 😂😂😂 worked great
Time to shine ❤️👏👍💪🔥
I would replace the oil filter housing with the metal one.
I recommend starting it wait 5-10 mins to get best reading
its a 13 mil drain plug and he didnt replace the O-ring on the canister. dont listen to this guy
Oil change required? Required for what?
What happened to the jeep series
You forgot to change out the O ring for the oil filter
That's that Mercedes/ BMW oil filter housing type. Careful about torquing on it. It can crack.
Replace the crush washer on the plug in addition to the oil filter o ring
It would help it drain better if you remove the oil cap and dip stick
2 things 1) don't forget to replace the oring on the filter lid. And 2) don't use a bud lite can, your jeep will run funny afterwards
I ran to to the comments after he didn’t say to replace the seals on the filter housing
Remember u should always lubricate the new oil ring in the drain plug if ur putting a new one and u should lubricate with the oil for the top of the oil filter
Try pressing the Unlock Button twice then lock then unlock again. The Jeep will do a light show for you, but remember that you’ll have to do this simultaneously. This only works with Dodge, Jeep, and RAM vehicles Plz try it and make a vid about it… I subscribed already
Where do you get rid of the oil?
I'd loosen the oil filter first then drain. By the time it's done draining the filter won't make such a mess
Screech from saved by the bell forgot to replace the oil filter housing o-ring
Next video: “how to change the oil cooler and thermostat on your keep wrangler”
Did you change the washer at your drainbolt?
You forgot to replace the gasket on the oil filter.
You forgot to start check it and verify there's no leaks at the plug or filter sir