Changing A Front Axle U-Joint In A Jeep Cherokee XJ
Автокөліктер мен көлік құралдары
In this video I change out a U-Joint on the front Axle on my Jeep Cherokee XJ. The axle u-joint on the #spookyjeep has been making a little noise so its time to change it before it completely fails. This video includes different methods on how to change out the u-joint and also includes torque specs for all the hardware. No video next week as I am taking the week off to spend quality time with my family. Hope you like this video and have a wonderful Christmas. Thanks for watching.
Jeremy Frye
P.O. Box 801
Mojave CA 93502
Follow me on Instagram : itsprojectventure
Please e-mail itsprojectventure@gmail.com for all business inquiries.
DISCLAIMER:
This video is intended for entertainment purposes only. The creators of this content and any affiliates are not liable or responsible for any property damage or injury as a result of any information contained in this video. Some links above are affiliate links which there may or may not be a small commission on the use of these links.
Пікірлер: 35
"I don't have a torque wrench that goes that high. So I am going slap it in, give it a few ugga dugga's and call it good." I am totally using this now anytime I need to tighten something.
@maddog45732
2 жыл бұрын
I've got a 2000 Jeep cherokee that I need to replace the front u joints in. Found a 250 ft lbs torque wrench on Harbor Freight. Now just need for it not to be so hot to replace it.
@ProjectVenture
2 жыл бұрын
I’ll have to look, how much was it?
@laurenceperkins7468
29 күн бұрын
Wheel bearings are one of the spots where you pay attention to what the book says. Because too tight can be as bad as too loose. If you *have* to do without the proper tools, the old-fashioned way is to tighten it until it just starts to drag, and then loosen it until it just spins freely. But with modern bearings the amount of leeway is pretty unforgiving.
Great video!
Liked and saved! I'll be doing this repair in a few days, I appreciate the detailed and informative video!
Great job. It was a very nice refresher. I need to do mine and it’s been years since I’ve done that. Thank you very much
Excellent job Mate. Thank you so much and I about to change my U-joint too.
Very informative video! I wasn't sure what the job would entail for sure but just found out during my last alignment that my driver's side u joint is very close to breaking and needs replaced. Thank you for your time sir!
Nice job I appreciate it
thanks big help
Thanks for this video it was extremely helpful
@ProjectVenture
3 ай бұрын
Glad I could help. 😁
When replacing the hub assembly always clean the knuckle really good and liberally use antiseize, I've had my current zj for 270k miles and plan have a long time yet, so whenever working underneath it use antiseize a lot, and even for living in the rust belt after the 1st time whenever have done anything things remain easy to disassemble for repairs
You should also note that Jeeps WITH ABS fitted are 30mm caps by 83mm in length. WITHOUT ABS fitted UJs are 27mm caps by 83mm length. So make sure you buy the correct size new UJs, as not one size fits all Jeep models.
What are we going to do without a week of Project Venture. Just kidding, hope you have a great time with your family.
Amazing 👏 video thanks
@buildingusa9604
2 жыл бұрын
Merry Christmas 🎅 🎄 for you and your family 👪 God Bless
It is so easy when you do those repairs :D
Grab front drive shaft and turn it back and forth and if your joints moving around it’s bad.
Just about to do my right hand side on my XJ... Im doing a full replacement of shaft/cv etc... hope it vomes out Nicely 😊🚙🇦🇺
@ProjectVenture
6 ай бұрын
Nice XJ. It’s so clean.
Can I check with you if the U-joint for the front axle and main shaft are the same?
@ProjectVenture
Жыл бұрын
In its stock form they are not the same.
nice video, did you drain the differential oil ?
@ProjectVenture
2 жыл бұрын
I did not drain the differential oil when I did this.
@orangek5
2 жыл бұрын
@@ProjectVenture did you use the spicer 5-760x-6 u joint? , i have an 2000 xj with abs, limited 4 door version, or are they all the same?.
@ProjectVenture
2 жыл бұрын
I’m not exactly sure.
@orangek5
2 жыл бұрын
@@ProjectVenture clear thanks
Will this be the same for a 2001 xj?
@ProjectVenture
9 ай бұрын
It should be.
@sparkythetraveler
9 ай бұрын
@@ProjectVenture damn, I appreciate the fast reply! 💪🏼
@ProjectVenture
9 ай бұрын
No problem. Good luck.
U-joints are in the driveshafts, proper nomenclature for the axle shaft ones is wheel joint,, the cherokee and grand cherokee took the same u-joint in all 7 positions until the model year when the manufacturer switched to cv type shaft in the front axle