How to easily change a CV boot, using a first price expander and an universal joint boot. All stages step by step
Жүктеу.....
Пікірлер: 27
@elmergarrett822 Жыл бұрын
today's date: 5-14-23. Just changed mine on 2006 jeep grand cherokee two days ago. Used a long funnel, trimmed the top to fit the cv joint, then boiled a pot of water, removed from heat and tossed in boot for 20-30 minutes. Worked great. Be sure and turn boot inside out, take large end and pull over funnel all the way, then when you pull boot back toward you, it unfolds itself, outside out...
@markiacono51772 жыл бұрын
The tool is definitely a easier way to go, but you installed a new boot on a birty and contaminated bearing. I like the tool for a fast fix but I'll still remove the joint Clean,inspect, and re lube it.
@azishaikh8500 Жыл бұрын
Very good work done big brother, you are having so much fun watching me too
@amethqal55302 жыл бұрын
Thank you very much i just replaced my cv axil boot on my minivan three days ago using your trick with the cola bottle to extend the tool
@fizumi1h1
11 ай бұрын
can you tell me about the trick?
@hoffmanscarab20102 жыл бұрын
Bro wtf this would have saved me so much time, so many of times😩
@tugberksongar2 жыл бұрын
Very good work friend ☺️
@geostorm9351 Жыл бұрын
Would only work for soft boots that don’t last long. Hard plastic boots will not stretch like that
@dean-gm1lg
7 ай бұрын
Bowl of warm water and always clean grease away from the boot seating faces before putting clips on
@richarddiaz8248 Жыл бұрын
Cool nice job
@ederangelo218 ай бұрын
My friends, what price an mechanic want to change an CV BOOT in USA AND Europe ? Some can reply me ?
@1776FreedomNow Жыл бұрын
how much psi is needed?
@SlackersIndustry Жыл бұрын
If going the easy route why not just use an easy boot?
@garypeatling7927 Жыл бұрын
Hitting end of shaft with welding hammer risky business
@freddytait7726 Жыл бұрын
Price of boot machine and name and where to get
@grisleigh4 ай бұрын
Did I see the ABS pick up ring on the Hub end? it appeared to smothered in the additional grease & Grime from use & the repair?? would this impede on the ABS functionality? I suspect it could be a potential safety issue?
@HGVCraig
2 ай бұрын
Just wipe the grease off so debris doesn’t collect around it. It’ll be absolutely fine
@sdyuk41452 жыл бұрын
ни рулевой ни шаровую можно было не откручивать а открутить только амортизатор и все нормально вытаскивается
@bobbyu899111 ай бұрын
Nobody does this anymore axle shaft is 50 bucks last one i did was in 1993
@eoinmurphy2109 ай бұрын
i just use split boots no bother
@chenmengqing2457 Жыл бұрын
Our brand would like to invite you to test our products for free, how can we get in touch with you?😄
@armedfarm34293 ай бұрын
No way would I ever hit the threaded end of the axel with a hammer, maybe a brass hammer, never a hardened steel hammer. yer asking for screwed up threads or an expanded end. But hey.
@ryanchenier-poulin85708 ай бұрын
goes over ring tone lol
@ryanchenier-poulin8570
8 ай бұрын
redacted lol
@boostedwolfie10 ай бұрын
This is a dead practice.
@johncollins830416 күн бұрын
Remove track rod end. Remove lower ball joint. Remove axle. Simples! Everyone else removes the vertical connecting bar and the brake assembly!! You've just shown you don't need to! Or am I missing something??
Пікірлер: 27
today's date: 5-14-23. Just changed mine on 2006 jeep grand cherokee two days ago. Used a long funnel, trimmed the top to fit the cv joint, then boiled a pot of water, removed from heat and tossed in boot for 20-30 minutes. Worked great. Be sure and turn boot inside out, take large end and pull over funnel all the way, then when you pull boot back toward you, it unfolds itself, outside out...
The tool is definitely a easier way to go, but you installed a new boot on a birty and contaminated bearing. I like the tool for a fast fix but I'll still remove the joint Clean,inspect, and re lube it.
Very good work done big brother, you are having so much fun watching me too
Thank you very much i just replaced my cv axil boot on my minivan three days ago using your trick with the cola bottle to extend the tool
@fizumi1h1
11 ай бұрын
can you tell me about the trick?
Bro wtf this would have saved me so much time, so many of times😩
Very good work friend ☺️
Would only work for soft boots that don’t last long. Hard plastic boots will not stretch like that
@dean-gm1lg
7 ай бұрын
Bowl of warm water and always clean grease away from the boot seating faces before putting clips on
Cool nice job
My friends, what price an mechanic want to change an CV BOOT in USA AND Europe ? Some can reply me ?
how much psi is needed?
If going the easy route why not just use an easy boot?
Hitting end of shaft with welding hammer risky business
Price of boot machine and name and where to get
Did I see the ABS pick up ring on the Hub end? it appeared to smothered in the additional grease & Grime from use & the repair?? would this impede on the ABS functionality? I suspect it could be a potential safety issue?
@HGVCraig
2 ай бұрын
Just wipe the grease off so debris doesn’t collect around it. It’ll be absolutely fine
ни рулевой ни шаровую можно было не откручивать а открутить только амортизатор и все нормально вытаскивается
Nobody does this anymore axle shaft is 50 bucks last one i did was in 1993
i just use split boots no bother
Our brand would like to invite you to test our products for free, how can we get in touch with you?😄
No way would I ever hit the threaded end of the axel with a hammer, maybe a brass hammer, never a hardened steel hammer. yer asking for screwed up threads or an expanded end. But hey.
goes over ring tone lol
@ryanchenier-poulin8570
8 ай бұрын
redacted lol
This is a dead practice.
Remove track rod end. Remove lower ball joint. Remove axle. Simples! Everyone else removes the vertical connecting bar and the brake assembly!! You've just shown you don't need to! Or am I missing something??