chainsawbars.co.uk - breaking and mending a chainsaw chain
Chainsawbars, advanced selectors for chainsaw bars, chains and sprockets - www.chainsawbars.co.uk/
Chainsawbars Selector - www.chainsawbars.co.uk/chainsa...
Carving Arena Selector - www.chainsawbars.co.uk/carving...
Custom & Bulk chain area - www.chainsawbars.co.uk/custom-...
Using our unique chainsawbars selector, it’s easy for you to find the right chainsaw guide bars, chainsaw chains, chainsaw sprockets and accessories for your chainsaw. We supply the largest selection of chainsaw guide bars and chainsaw chain for Stihl, Husqvarna, Echo, Dolmar and other chainsaw makes and models.
Пікірлер: 33
Well done sir, Thanks for a very well executed tutorial. Easy to understand and follow with good photography.
You are a scholar and a gentleman. Thank you for sharing this information, and what a great video.
Excellent explanation. Thank you.
Nice video, thanks for posting.
Excellent. Thank you for posting
Great video. Thanks.
Thank you, learned a lot
Thanks for the vid.
i always wondered what was used for this thanks for posting
Thanks great vid !!
Very nice video, cheers thanks for sharing
Just got one off eBay, now I know how to use it!
waoo i didn't know that it cot be done thanks for shearing. greetings from DK
I rate this completely Pensioner proof,, easy to understand Just what Doctor Rob ordered , only need the kit now, xmas coming,,, ""the old Buffer""
great post and instructional video! products made from my home state Oregon!
@skylerslideways6761
10 жыл бұрын
The bar says made in Oregon , its at least cool to see that even if it is made in Italy. Just saying .
@andys8718
2 жыл бұрын
Maybe Oregon, Italy? Kidding...
Wheere do you buy the chain role. All sites [ebay/aliba ] expensive
How do you get the rivet head to flatten out? Is there a special rivet tool that holds the rivet central when you spin a new one in? The rivet head is not flat on the new rivet installed but is rounded, not like the original. The one i got from Harbor Freight was real sloppy in the spinner shaft and real sloppy in the threaded thrust hole. I found the spinner head in this tool to waver off the rivet head on turning it even though i held the thrust handle centered tight to the rivet head. I feel there should be a new type spinner rivet socket that has a small center hole to align it correctly before starting the spin and as it spins in the hole keeps the rivet straight and the socket should have a flat center with beveled solid rounds with angle ridges around the bevel to roll the sides of the rivet head down accurately, but of course i am not the one that designs them but if i did it would be this way.
@chainsawbars
8 жыл бұрын
+John Doe If the rivet tool is worn then this can cause it to slip. A new anvil does have a small center to align it and this anvil should be replaced as and when.
@JohnDoe-go2fc
8 жыл бұрын
I think i got it now but what was happening was when i did the turn it would rotate off center and i found the alignment was off horizontally. I bent the tool and it screwed straight.
one of the best video I've seen so far in my quest. I was wondering,can i break and mend a chainsaw chain manually (i have no specialized tools) ty
@bodders1029
8 жыл бұрын
+Aurélien Carnoy its a bit of a fiddle with the right tools unless you are doing a chain a fortnight i would just get your shop to sort it.
@chainsawbars
8 жыл бұрын
+Aurélien Carnoy Sort of but you can make a mess of it as the rivets are so small. Much better as said below - get the right tools or take to your garden repair shop.
@aurelienyonrac
8 жыл бұрын
+chainsawbars thanks
@segsepuloni9795
7 жыл бұрын
just grind broken links off using angle grinder, put new ones on using a ball pein hammer. just hit the centre of the preset to mushroom it over, and done.
I have a new punch (#26870) and it seems too long as I can't place the rivet under the Oregon breaker
@chainsawbars
4 жыл бұрын
Not sure the punches we well work fine. Rob
I like the up close video but don't hold the camera because it shaking all over the place mount it so it stationary
Is it worth making your own chain?
@jonmuck6161
3 жыл бұрын
Depends on your situation. If you have multiple length bars you can just keep a roll of chain and make whatever length you need. Also great for odd length bars.
Think we have all made a tight one and just set it up the bar abit and let the saw loosen it up lol
Travail parfait et Oregon made in Italy parfait, maintenant Oregon made in China=0