Great instructional learning video. What is an IPA brush that is mentioned at the 4:20 mark? Fantastic flights.

@sandfac3427

7 ай бұрын

Thanks. IPA = isopropyl alcohol. Here's the process, which is outlined (I think) on the Easy Built Models website: 1. cut oversized square of tissue over entire insignia "footprint" 2. Liberally apply gluestick to back of tissue and allow to dry 3. Put tissue glue-side down over a cutting mat, tape a paper template over, and cut out insignia with a #11 x-acto blade 4. Use a piece of painter's tape or something similar to align letters on wing or wherever, and place each letter on then soak through with a brush and 70% or 91% isopropyl to re-activate the glue stick and adhere the marking. I often have to do a little touch-up with glue stick after to get all the corners stuck down, but this works pretty well.

One of the best - if not the best- rubber fligths I've seen on YT. Amazing job!

Sends me back to 1970's !

I've been into aeronautical hobbies for 30+ years. Never understood the rubberband group until seeing this. That sir was extremely impressive and I applaud you on your build, and flight!

Very nice model! Seems to fly better and longer than many single prop models.

Watching high level stick and tissue models flying, restores my faith in humanity; not everyone has to buy RTF planes made out of foam.

Must be pretty light, Oliver! Excellent build and flights!

Proud to know you and fly with you young man. This is how I started 2024 - watching you work magic. Thank you..

@sandfac3427

7 ай бұрын

thanks VG. Happy new year and you know that your mentorship and flying of jumbo small-nacelled ships was essential for this project!

I love the simple artistry of rubber band powered flight.

Amazing ! ....... I sat mesmerised through the whole thing, whilst my breakfast went cold over on the counter.

Nice. Hope to see it at Geneseo in 2024!

Great work Oliver!

Fantastic airplane! I would love to build one and convert it to electric power. I just don't have the patience!

Really impressive, congratulations!

Great video, super project, even really nice music. GOOD for you ! I am goofing with just flying models not scale and love the idea of the multi-motor "A" frame since I was a kid (60's) Left hand props were a bugger... but now with UAVs LH props are everywhere. Still have to convert them over and they are dense and heavy but that helps in a tractor project but gawsh awful in pushers. Keep'em flying.

@sandfac3427

12 күн бұрын

Thanks for the comment. I'd be interested to hear how a twin pusher with drone props flies, I'll bet you could get it going. There are many ways of doing left hand props that are less time-intensive than the traditional carving method -- laminated-fan, formed over a cylinder, or there are even people 3D printing out there... however you choose to do it, go for it.

Really enjoyed your video! There are a lot of excellent techniques in your build, each worthy of its own video. Bending balsa for the tail, adding the bass lamination, formula and technique for the prop build, applying wet tissue, and the list goes on.

Very cool congratulations!

That would make a gorgeous light R/C park flyer! Suggest having the props counter-rotate outwards (at the top) for more stable flight. Several full -scale aircraft do this- the Lockheed P-38, Henschel 129, and Convair Model 48 Charger.

@sandfac3427

12 күн бұрын

Thanks for the comment. I switched this plane from two RH plastic props to counter-rotating over the top balsa, and the climb was much more straight.

Such beautiful work, and classy choice of music. Thanks so much!

Congratulations Oliver, great project! I have fond memories of the first FAC Nats you attended. We shared George White’s shade. I was impressed with your enthusiasm and how much you had been able to learn from the internet. Again, great job!

@sandfac3427

4 ай бұрын

Thanks Gene, great to hear from you! Coming up on 10 years since that Nats in 2014. Your and George's mentorship that week was really special and a huge help, had never been to an FAC contest before and I remember almost losing a Moth by the end after your trimming suggestions! Multiple people told me and my dad afterwards that we'd found the best 2 guys to share tents with as newcomers. Planning on going back to Geneseo this summer with more models to fly, hope you are doing well.

Great job! That glide was dialed in!

Nice build. Nice flying bird. I was building rubber powered paper (Japanese Tissue) and stick planes back in the middle 50s (I'm now 79 years old). I don't remember a single one flying as good as what I've seen in this video. These days I fly RC foam and foamboard planes but not stick. Stick planes tend to break into too many pieces when crashed. 😢

anyone whoe can build something this great is a genius, an artist, and a fine craftsman!

@sandfac3427

6 ай бұрын

Thanks for the kind words.

@petermach8635

6 ай бұрын

Aren't they just !

Amazing!

@sandfac3427

6 ай бұрын

Thanks! Glad you made it over here, love your videos. Balsa and tissue will always be a great medium, I get a ton of enjoyment out of these builds.

good glad to help. flu rubber band for years

very nicely done your smile says it all

Amazing flight...! Thanks for sharing

Great ! Nice work and flight !

beautiful build beautiful flight.

Fantastic build and flight! A real masterpiece of engineering and handcraft. It is so hard to get even a single engine plane to fly and here you are flying a fantastic twin engine even without the cockpit! Thank you for inspiring!

@sandfac3427

6 ай бұрын

Thank you! Many great videos on your channel, subscribed and looking forward to seeing your next projects.

@downwindchecklist6567

6 ай бұрын

@@sandfac3427 Thank you!

Great tutorial on a very interesting model. I love how floaty your planes are trimmed to fly- must be very light. Could you consider a tutorial on what you've learned on keeping it light, techniques, and some baseline examples of what your models weigh with and without motor? Thanks!

@sandfac3427

6 ай бұрын

Thanks for the suggestion. I tried to keep this one light, and its big wing helps a lot to keep the wing loading down. A lot of keeping it light comes down to using light balsa (sub-8 lb/ft^3), light structure, and not painting too heavily, if at all. Looking at a Guillow’s kit vs most dime scale plans will give you an idea of the structural difference im talking about. Some of my other videos have weights listed for the models too, but more comprehensive is a good idea. I’ll keep that in mind for future videos

Excellent work! :)

My planes always fly WORSE with handmade props! Wonderful project. 😊

Perfect.

Excellent flight. Maybe use a rudder timer to control turn to help in recovery. 👍

@sandfac3427

6 ай бұрын

Thanks. I thought about making it removable-RC, and adding a DT, but ended up going for simplicity since the plane is a lot to handle as it is. Rudders on timers is always an interesting thought.

Excellent 😊👍👍

Nice ! You guys have to come down to Tuckahoe this year

@ericbitzer5247

17 күн бұрын

Where exactly is that? I remember going through it with my old boss, but don't remember where it was.

Bravo. Love seeing people building unique projects and making it happen! What’s next?

@sandfac3427

6 ай бұрын

Thanks. Working on a large RC towline glider and free flight peanut canard.

Only way to fly. Free Flight forever.

Nice build, smooth editing and great flights. Did it look a bit beaufighter-ish in profile when the nose fell off to you too? Loved the music.

My models fly much worse than yours WITH their noses and nose weight attached... I like the horizontal keels on the nacelles. Using that on my next rubber multi.

@sandfac3427

7 ай бұрын

Thanks Monz, Dave knew what he was doing using a minimum of balsa to achieve a 3D shape. Excited to see what you have in the works!