Good video. Note that this centrifugal clutch kit is intended for use on one of several Chinese--made bicycle motors. These are all made with a manually-operated dry-plate clutch similar to that on a motorcycle. However, with a tiny engine and no gear shift it's rather difficult to start off, for the engine likes to stall. The centrifugal clutch allows you to get off to a very smooth start, for those three big clutch shoes are meant to slip (and they get hot.) The centrifugal clutch rotates the old dry-plate clutch, and that dry-plate clutch rotates the front drive sprocket. Yes, it requires a certain amount of work and a certain amount of mechanical experience as well. In general, if you can repair a bicycle or a lawmower you'll have enough skill to work on a motorized bike, which requires quite a bit of tinkering just to keep it running even without a fancy clutch.

@peterkay7458

5 жыл бұрын

TY Mark I was honestly wondering what the point was and you helped me remember someone esle said they lack the torque to start from a complete stop unless you pedal.

@markkinsler4333

5 жыл бұрын

Yes. I should add that the stock clutch--the one that's lever operated--probably works much better with the 49cc engine if you're a 100 pound kid rather than a 200 pound senior citizen. It can happen to any of us, I suppose.

@pauls5745

5 жыл бұрын

+Mark Kinsler but of course you have to pedal to about 8mph. these are not similar to motorcycle/atv clutches where you can rev and dump the clutch. they have very little gripping force

@doctorspice1557

5 жыл бұрын

Wow thank you for telling us what it does cause for people who dont know what it does will now know an explanation should have been in the video. The video was a bit too long for my taste tho

Great video Fabian. Your attention to detail is second to none. Good timing also, I am installing mine next week so that gives me time to order 4 more gaskets. So easy for one like my self with no experience to follow your tutorials and feel confident about doing a top notch job.

Great job. I love working on these engines. They are cheap enough for me to practice my tuning and modification ideas on. I think this is a great idea.

@integrationofmanandmachine4714

4 жыл бұрын

What

This guy and his content is bloody amazing! Has anybody ever come across a guy as clear in his instruction as him? He is by far the best bicycle mechanic out there and the wat he teaches is the gold standard... In 2021 bicycle engines are all the rage now and only going to get bigger yet none of my pals from my club have heard or seen this guy! I'm sharing this to everybody and I hope this fella gets what he deserves and he might become a leading voice for the masses on mechanical issues. Awesome channel!!!

After you've installed your certificate clutch do you need the clutch cable anymore

Very well put together this video I've learned a few tricks I wouldn't have thought of.

I am so thankful for this video. 8yrs old and still helping others! I’m finding that the 3 alignment posts on my clutch assembly appear to be longer than yours…too long to allow the cover to fit. I’m tempted to remove them and grind them short enough for the cover to seat properly.

I'm considering doing this mostly because my stock clutch is slipping and this seems like the only decent upgrade that would permanently fix it. I already did the shift kit, and pull start, and upgraded intake. As a side note, I'd tighten the crap out of the flower adjustement nut before sticking the new cover on just so you don't get any more slippage from the original clutch.

Good video. I just ordered a centrifugal clutch for my bike and now I know how to install it

@shabibhajab7092

Жыл бұрын

where did u order it?

@briggsmechanicalservices

Жыл бұрын

@@shabibhajab7092 off of eBay at the time, have no idea if they still have them

Thank You for this video..! I followed your steps to the letter. You'll need those diamond bits from Harbor Freight on your wiz wheel to cut a hole in the gear. I thought this would work without the hand clutch nah unless the "2 positions" made it too tight? It does pull way better off the line, No more bogging .. the out put shaft bolt is 8mm fine thread less than 1-3/4" my kit came with the wrong install bolt.... peace

great tutorial, can't wait to do this to mine

Good morning, I have the same clutch installed on a 48cc engine. What no one mentions is that the nut (plug) on ​​the stock clutch side housing is for charging oil into the system. Yes, this clutch is hydraulic. It needs lubrication and the oil it uses is centrifugal clutch oil, SAE 20W30. It must be filled with this oil up to the edge of the fill hole. Both the original clutch and the centrifugal clutch are in an oil bath and work perfectly. Greetings from Argentina!

Great tutorial, i dont have a motor at all. But i watched it all as it was very informative. Only thing is please put some more lumens on the subject. A Led headlight would be the way to go. Thanks.

thanks Fabian I thought that the centrifugal clutch replace the regular, because on the vid. you removed the set screw by the flower but and then you tight it ,so that engaged the clutch and the centrifugal clutch will do the job if you can ..can you explain the reason to keep it thanks for your vid. I'm going to get a engine gt5 ported and add the jack shaft I owed a trek 660 mountain bike with hydraulic disc and the frame looks a bit small do you know the minimum space need it to attached a engine thanks for the help

hey fabian i just a got a clutch kit and does the extension sleeve just slide on all the way, cause mine stop and i cant get the second cover to go on when i put the clutch on

This video is great and helped me a lot with my own centrifugal clutch. I have a question: the one way bearing stop engaging after a ride. I have to pop everything open and clean the bearings (the five small pieces) to remove the grease in order to make it work again. Is this normal?

What engine do you recommend for the longest lifespan? And what components would you replace/upgrade to make it last as long as possible?

Probly put 1500 miles on mine over 3 years or so, the clutch is still good.

I'm glad that I am not the only one who has air leaks in his compressor.

I want to put one of these on my bike, I have an 80cc Roadstar kit bought off of Amazon. What happens with the old clutch? It just stays there? like a secondary, if I want to manually release the clutch? (it'll just run normally like an automatic clutch until I pull the lever in which case it will release and no power will be applied to the wheel?) Also, will I need to buy a pull start?

Can you tell me where I can buy that kit for installing a centrifugal clutch on my bike? Mainly the extension housing for the clutch. Thank you in advance!

Great vid very helpful. But what are the pros and cons of doing this

Hey,do you know anyone that works on these motors. I have a zbox with sickkit but dont have the expertice to fix a suspected clatch issue.... Thanks!!

The best way to drill the little oil hole in the bell bushing is to use a 2mm diamond bit and a dremel tool. Takes about 5 mins. and the bits are very cheap. You wont break it easy like the carbide bit either. It works great, I've done it many times. 10 of the bits in a pack is only about 6 bucks. Try it, Very easy..

Does anyone know if this kit from JNMotors includes the gaskets, especially for the new round cover? Their website picture does not show any gaskets. Also, how does this kit compare with the kit on PistonBikes website?

Hi. I have this classical cruiser I'm working on, I see all these centrifugal clutches, but which did you use? My engine is the same as yours

This is great for people with knee problems that have trouble peddling on take off . I've been riding this style bike for a year and a half and I've never seen or knew the need for such an attachment . I love my bike and it requires much maintenance . This isn't for me now , but maybe later . Good video !

Once the engine is started can you accelerate from a dead stop our do you need to pedal 1st, and how long does the clutch last once properly installed

Please write me where you bought

Do you know if on the JNM website where they sell these for $45, if the kit comes with the crankshaft extension sleeve?

In which direction do you rotate the flower nut 2 index points? Clockwise or counter-clockwise? Thank you.

ALLOT of work to just install a centrifigal clutch! Is it really worth it?

so what is the purpose of the small wire on the bearing casing, inside the clutch bell? Does it need to be there?

to free a stuck clutch 66cc all videos say clockwise hammer the 3 pins mine will not free. please help

Hello again I did what you said about putting 4 gasket onto the clutch extension housing that did solve the problem I ran into another problem but was able to get that resolved that was with the small pins that goes into the clutch bearing what I would like to ask you now is when I turn the clutch where it's not engaging with the engine I notice that the drive gear turns do it suppose to do that also the clutch arm did you connect the clutch cable to that or you just left it alone without the clutch cable

@fabian F where do you find these parts in 2023? amazon isnt much help unless i am missing somthing

hi i have a gt7 pro racing motor how to hook up the clutch and the carb

Where do I get one of these centrifugal clutches?

What it's the Dyameter of the axle ? 3/4" or less ?

Awesome video very informative thank you

So I can still pedal and dump the clutch to start like normal but don't have to pull in the clutch to stop?

Thanks for the details. Im building my 4th bike. Will be installing centrifugal clutches soon.

@SuperRobvan

4 жыл бұрын

hey chon im starting to build bikes to when done what do you sell yours for? just kinda looking for idea to be at in price..

So ive read thru the comments and watched the video and just want to be sure i am doing this right before i screw up one of the last available centrifugal clutches im goin to abbreviate the clutches as CC and MC so does that flower nut get screwed counter clockwise or clockwise n my application is on a dirtsurfer i have built myself with a jackshaft n the right size gears to retain normal ratios of a 45t rear sprocket so that i can use an internal 3 speed hub to help with hills n high speed n eliminate the need to move the chain from sprocket to sprocket n it keeps the chain from going thru my right ankle and instead raised up to go over my right foot toes i dont have any means to pedal it n wont always have a hill to jumpstart it so i have a pull start but im trying to keep down the number of cables that run to a sawed off handlebar i have one for gas one for brake n one to shift the rear hub so i really only want to have the centrifugal clutch operating is there anything i need to do to make sure the MC is engaged or allowed to spin freely at all times n allow the CC to only engage when given gas should i just remove the MC gear completely since i have a pull start and couldnt pedal start if i wanted to basically all the reasons i saw u had suggested to keep it are irrelevant to my application or will it interfere with the operation of the CC n about that flower nut if u suggest that i do remove the MC that would be gone correct n if u suggest that i keep MC gear does the MC need to be engaged constantly so that it will spin freely n how can i accomplish this without an extra cable and a clutch hold on the lever

hey all question to those who build them and sell them,,i just started building mine so what ball park figure do you sell yours at? don't see them to much on craigs list except the whizzzzer ..I just wanna price mine accordingly

Would it be possible to modified with gear system

Given the relative ease of removing the clutch shoes, and the fact you mentioned you can go about 100km before replacing the lubricant, wouldent it be easier to just remove the clutch bell for regreasing when the time arives? similar to a car oil change?

very well explained.

where can i find a centrifugal clutch kit for the new ztmoto phantom 85 v3 ??

Does the centrifugal clutch make the bike take off faster from a stop?

Hi I have a question. I have a 80cc bike motor ok when I. Pedal and released the clutch the motor has to. Turn on right mine doesn't it don't turn on so if guys know how to fix it I will really appreciate that

Great job,thank you

how do you loosen the centrifugal screw mines not coming out

Hi I am installing a centrifugal clutch on my motorize bike however I ran into a problem that I am not sure about when I install the extension housing my flower nut is hitting against the burge in the extension housing what I would like to know did you run into this problem when you installed your extension housing if so how did you fix the problem

can you tell us where u got the kit great vid!

Hi.can i kno something ..i also have this engine ..am i need to put engine oil for before use.

fab thank you for your clear info.

Where can I buy the centrifugal clutch kit?

How do you remove crankshaft bolt

Nice, very informative. But I was wondering, since you already greased up the extension sleeve, is it really necessary to drill the gear and case for lubrication? I mean I know you'd want to periodically check to make sure everything is a go, and with regular motor bike maintenance wouldn't be too much out of the ordinary no? I'm just asking because I'm trying to find out if it's absolutely a necessity thank you for the very informative video. ☺️

Does this mean that the original clutch is locked in place permanently so it doesn't slip or spin does that mean you don't need the clutch lever either or am I wrong.

i love this video

This is a very nice and meticulous job but id like to know if you yourself manufactured all those parts?

Do you know where can i get a kit , centrifuga clutch or the extension

@kxlucifer

6 жыл бұрын

juan vera ebay boygofast

Cool video 👍

This is a good design.

Can you replace this centrifugal clutch with a bully clutch.

would this work on a fat tire bike??

Where did you get your centrifugal clutch?

Hi, great video. how did you remove the flat head bolt that held on the small gear?

@integrationofmanandmachine4714

4 жыл бұрын

Come

I must hand it to you Fabian you really know your shit, when I was looking up the shift kit I could never find anything on how to put it in on KZread, then I found your video and it was a grate help in making me decide if I wanted one or not, everyone was saying they are a waste of money, but they just didn't know what they where doing, and again with this clutch, you really make it easy for everyone thank you, YOU'RE THE SHIT! XD

@cryptopyro

8 жыл бұрын

+Crying Angel I'm happy to be of any help. The shift kit and centrifugal clutch are the best thing since sliced bread, and from what i understand SickBikeParts have the "Ultra Heavy Duty Freewheel Bearing" system for their shift kit, as an optional accessory, not that the shift kit isn't bullet proof with the White Industries heavy duty (rebuildable) freewheel bearing system.

@Ozzy-DRZ-Adventures

8 жыл бұрын

Cheers, I live in QLD in very steep, dusty and rocky conditions and that's why I want a shift kit, and I seen the chain guides you made up on one of you video's for it, I'll be sure to copy it when I get my one. Oh and is the expansion chamber exhaust system from sick bike parts any good if u have one?

@cryptopyro

8 жыл бұрын

+Crying Angel The SickBikeParts expansion chamber is very good, but i haven't put it on the bike, as it makes the bike look like a motorbike, and there is no way that you would get away with it if the police pulled you over. Unfortunately, there is no way to easily hide an expansion chamber on the bike, so i'm just using the standard exhaust system, though with slightly modified baffles in the standard exhaust system. The chain guides are absolutely essential if the bike is going to be bouncing around over rough terrain.

@Ozzy-DRZ-Adventures

8 жыл бұрын

Lol it will and a lot, my place is all hills and rocks, the standard drive chain has popped off of the guide pulley once already I was lucky i was going slow, the chain got stuck up in the drive sprocket I'm lucky it didn't crack the engine case, but I modified it and its good now, thanks again for the helpful advice man really appreciate it.

@mick7793

6 жыл бұрын

the expansion chamber exhaust system is the best thing for the money !!!

how do you get yours started so easy just by turning it, i have to go on the otherside with a drill or pull start to get mine to start

@cryptopyro

5 жыл бұрын

It's simple technique. Work the engine to just over top dead centre and then start the engine.

Where do u buy that

Do they make one for a BT 100cc?

where can you buy everything you need for this mod

I found out that the newer kits (possibly even the old style) do not need a hole drilled for grease Fabian. Cleverly enough they machined a bit of the gear part of the clutch bell so they could press it into the bell, they leave enough teeth at the pressed portion that the teeth actually act as full blown channels for the same grease that lubes the gear work, at engine speeds this actually presses lube directly to the one way bearing.

@cryptopyro

7 жыл бұрын

The issue, is not the one way bearing. The issue is lack of lubrication between crankshaft extension sleeve and the clutch bell riding surface. The one-way bearing is "not" a load bearing part of the clutch bell.

@jacobschmoyer7630

7 жыл бұрын

The bearings push lube down into the sleeve do they not? Unless the design of the kit I have is different from yours. Did your sleeve come with a hole drilled into it from the outside, about midway, to the inside, comming through the puller tools threads.

@jacobschmoyer7630

7 жыл бұрын

Threads for the puller, I mean.

@jacobschmoyer7630

7 жыл бұрын

And as an additional question, if a person were to drill a couple smaller holes instead of just one larger, could the force of the gears meshing push grease through and onto the shaft reliably

@jacobschmoyer7630

7 жыл бұрын

My gear and bell all appear to be stainless steel material, they should be able to stand up to a couple holes right

Can I make it a wet clutch just like a bt80?

I am unable to get the crankshaft extension sleeve on the crank shaft far enough to have the clutch housing to recess as much as is needed. I cleaned both the shaft and the extension as prescribed by you. Do I have a bad extension or am I missing something? Thank you.

@kxlucifer

8 жыл бұрын

maybe you forget to remove the wood draft key?

How does the extension sleeve mate with the crankshaft? Is there a keyway inside that sits in with the keyway slot on the crankshaft?

@markkinsler4333

5 жыл бұрын

No. Extension sleeve is bolted onto the end of the crankshaft with a single center bolt. The designers omitted both key and keyway, probably because there is insufficient room available and the torques involved with the centrifugal clutch are smaller than those when you're using only the disk clutch.

I thought those clutch kits come with a pull-starter, do you just pedal to start it like normal?

@TacticalPhoenixYT

11 ай бұрын

yep, one way bearing.

thanks bro good video

What is the name of that clutch I've been looking for one

But now you have to have a pullstart right?

were did you get that cluch?

What is the purpose for the clutch ?

I'm having trouble with this kit. I thought this would be more or less universal, right? Well that's wrong, and now I need help, because I can't return it... I'm having two major issues. The crankshaft is too large, so the sleeve doesn't fit on it, and the manual clutch housing is too shallow, so there's a half inch gap between the engine side and the cover for the centrifugal clutch. I know that comments for this vid are probably dead, but if Fabian could direct me on how to resolve these issues, it would be greatly appreciated. Btw I'm using the BBR tuning 80cc black engine.

@keeganhache6667

4 жыл бұрын

Meucas try taking it to a machinist shop and get it made to the proper sizing. Then it should slide over the crank shaft. Then try making a half inch gasket and put it in between the cover and the engine. Then put the bolts in. Hope this helps you. I have a Harley-Davidson motorized bike and I have to make brackets and clamps for it all the time. The crazy part is I’m only 11 and I know all this stuff. Good luck with your project!

@person-ce8cr

3 жыл бұрын

@@dave-oc6xk why are they junk? is it just the quality

I've been spending quite a lot of time, soaking up your great information tonight... Good job! I'm getting ready to buy a bike and engine and still wondering about the 66cc vs the Honda 49cc 4 stroke. One of the reasons I liked the 66cc Chinese engine was that it is less expensive but now that we're talking about adding another $80+ to the build.... It seems to me that the Chinese and the quieter 4 stroke are almost exactly the same price.....because the Honda, I believe, automatically has a stock centrifugal clutch ?? Do I make sense... Since you have thousands of miles on the 66cc engine, I'm very curious to ask for your opinion as to which engine I should buy and for what reason? Thank You!

@dangerousdoggo5465

5 жыл бұрын

2 stroke you can go 60km/h lol

@commandercody38

5 жыл бұрын

The 66cc engine gets better performance and less maintenance.

How do you get the clutch apart to file those edges Fabian. Mine is brand new and I do not want to force it. I have already broken enough stuff learning by trial and error on this build.

@cryptopyro

10 жыл бұрын

There are two ways of going about it. The first method is to use a pair of flat blade screw drivers to try and force the clutch shoe disk away from the crankshaft extension sleeve by placing screwdriver tips in between the clutch shoes and the inner face of the clutch bell. This is a tricky procedure because it can take a very long lime to slowly wiggle the clutch shoes so the disk frees itself from the extension sleeve. There is also a risk of bending the clutch bell housing, which will cause permanent damage to the clutch bell. The other option is to use the crankshaft extension sleeve extraction tool (supplied in the centrifugal clutch kit) to remove the extension sleeve, as well as the clutch shoes in one single operation.

@ramani1008

10 жыл бұрын

I used what was supposed to be a cobalt bit from eBay and a carbide and tungsten bit from home depot and only made a scratch on the surface. I guess I will have to forgo the oil hole unfortunately.

@cryptopyro

10 жыл бұрын

robert apple Typically the drill bits from eBay and Home Depot are only surface coated HSS drill bits. They are for the most part completely useless. A proper 2,5mm cobalt drill bit works out to be around $10 I also need to mention that a conventional single speed drill press spins too fast, and generates too much heat when trying to drill through hardened steel. You will need to use a multi-speed drill press, set to around 200 rpm, as well as continuously applying a light cutting oil (or transmission oil) on the drill bit and making sure you frequently pull the drill bit out of the hole to make sure it's filled with cutting oil. When starting the initial phase of the drilling process, you must be extremely careful because the very outside cutting tips of the drill bit (if stating out with a 2.5mm drill bit) will dig into the angled faces of the gear, and can tear away the outer cutting tips, causing the drill bit to become completely useless, in an instant. The hardest part of the drilling process is to very, very slowly cut into the angled faces of the gear teeth, till you reach the bottom outside face of the gear, i.e. till the drill bit just bites into the floor of the gear teeth. This very slow process can take up to 10 minutes - it's an agonisingly slow process, and the whole drilling process can take from 30 minutes to 45 minutes, just to drill one single hole.

E possibile avere traduzione per centrifuga l 80cc.

Is this an 80cc kit or a 49cc kit?

Your video only has a link for the chain lube where can I get the centrifugal clutch?

@SuperRobvan

4 жыл бұрын

amazon or bikeberry or kingsmotor bikes

How do we order this kit?

on this video you see the chain tentioner well it has aluminum guides with holes in them its those,s i,m talking about did you modify them where can i buy them

@cryptopyro

10 жыл бұрын

Those guides (or idler wheel flanges) are just the original flanges that have had the cream coloured powder coat removed from the aluminium; to give it a brushed aluminium appearance. I simply drilled holes in the flanges to improve the appearance of the flanges.

@stingray300m5

10 жыл бұрын

ahhh i see well you did one hell of a job on those they look professionally built

@cryptopyro

10 жыл бұрын

stingray300m You can easily achieve the same effect by using a hole saw to drill out an appropriately sized (bare aluminium) disk out of 1mm aluminium sheet, or alternatively make a trip to a bolt and washer store and purchase some aluminium washers with a 5mm centre hole. Marking and drilling out the 8 peripheral holes is also easy. Simply use a ruler to mark a horizontal line through the centre line of the centre hole, then turn the disk 90 degrees and mark another line to effectively form a cross on the face of the disk. Now measure the distance in between the outer edges of each section of the cross and mark a reference line in between the 90 degree cross edges. Trace a complete line by placing a ruler on the marks you've just made. You will have a total of 8 equally spaces lines on the surface of the disk. Take your ruler and mark a line 6mm in from the peripheral edge of the disk on each of the lines. Take a centre punch and gently make an indentation on each of those points, so that a 3mm drill bit can get started without wobbling outside of the lines you've just made. Drill through the alumnium firstly with a 3mm drill bit, then stepping up to a 4.5mm drill bit, then stepping up to a 6mm drill bit. You have now made an idler wheel flange as shown in the video and as shown on the website.

Why would you keep the old clutch and have no drive to it seems impossible for it to work

I like these centrifical clutches but they have a couple of weak spots to them the mainest one is the one way starting bearing assembly when you get a couple of mm slack when you get slack between the roller bearings and the one piece that connects to the crankshaft it spins the the centrifical clutch Part when you go to pedal start it or roll start it the clutch slips like hell the most likely cause for this is the spring inside of it breaking or excessive clearance between the roller starting mechanism it's got a very hardend spring that you cannot find anywhere so you have to make your own spring but you have to put it on the outside of the clutch bell because there's no clearance near the small gear and tie it up with wires in order to do that you have to modify the roller bearing carrier to where you can fit a paper clip without the paperclip touching the inside centre Part where it spins but I'm working on a method where I'm putting the actual one way starter outside of the of the clutch I'm going to take a strip of metal bend it and Shape it to where it fits around the clutch drum and then I'm going to put some glue under it for traction and then clamp it down with the hose clampand then put a weight on the other side of the hose clamp so that the hose clamp is balanced when the engine spins and then I'm going to put some type of homemade starting cogs mechanism on and then when you pedal start it I'm going to put weights on the end of those starting cogs so that when the engine starts the starting cogs are going to pivot in subtract inword under centrifical Force but I'm also going to put light springs on it so that when the engine is turned off starting teeth arms will go against the outer starting mechanism I might end up putting a couple of KZread regarding everything I left out a couple of details oh how I'm going to go about the whole thing exactly

So does this still use your factory clutch to drive the 10 tooth sprocket ? i just read through over 300 comments and didn't find the answers to any questions looks like you don't answer the majority of your viewers questions, your viewers answered more questions than you.

Where to buy centrifugal clutch and the extention cover?

@cryptopyro

9 жыл бұрын

You can get the centrifugal clutch and pull-start from a few different vendors, but i purchased my centrifugal clutch and pull-start through JN Motors: www.jnmotorsbikes.com/product_p/jnm1166.htm ************ www.jnmotorsbikes.com/product_p/jnm1170.htm

I'm so hyped

Where can you get a centrifugal clutch kit???

@person-ce8cr

4 жыл бұрын

On ebay. Just look up "80cc motorized bike centrifugal clutch kit"

Where can I buy this?

where do I find the clutch kit?

@kyleshaw5538

11 ай бұрын

Did you find it?