BENT COIL CONNECTOR PIN: I had an annoying and hard to trouble shoot P0300 code on my 6 cylinder 2003 GMC Envoy XL. I had replaced the spark plugs and coils and the code and misfire would not go away. Why it did not trigger a P030x error, I don't know. Just passing this along as something simple for others to check. Have a nice day!

Your videos dont get enough views but they are very informative, good videos bro

Thank you so much

Thankful for this informative video and the subscribe button!

Fixed a P0300 code that I had been fighting for a year after installing a new transmission on a 2010 wrangler . I literally did everything . Ended up pulling the transmission and replacing the new flexplate I had installed with a OEM transmission . It was made wrong and sending the wrong signal to the PCM .

Im getting this p0300 code and 3 other codes. Im getting p0050 p0097 p0102 and i already replaced the mass air flow sensor along with the maf wiring harness im on a dead end with this any help?

@HVAC_Mechanic

Ай бұрын

If the MAF sensor is new, it is likely in the wiring. It also looks like it has the IAT sensor built into it. I would get schematics for the vehicle and test the MAF sensor wiring, as there is likely an open or short. Also, be sure to check any related fuses.

I have the ,308 code no other codes cylinder 8 ? Ford flex fuel engine. Been to ford theee times no luck now no money. One other says engine running rich at o2 sensor.

@HVAC_Mechanic

4 ай бұрын

If another code is saying Running Rich, I would check the injector on cylinder 8.

@cbx500cbx

4 ай бұрын

Thanks, someone said ck lifter on cyl 8 too.

❤❤❤

👍👍👍

I'm now getting a p0300 and a p2097... Replaced both O2s and cat is new.. also getting misfire p0301 302, 303, 304. 4cyl motor.. engine is running fine.. I don't notice a misfire or hesitation... Should I still suspect the coil packs or plugs? Please help me out.. running out of options.

@HVAC_Mechanic

Ай бұрын

The "P2097 Post Catalyst Fuel Trim System Too Rich Bank 1" is likely the cause. Something is throwing off the air/fuel ratio causing more fuel than air to go into the cylinders.

@TimeLapseCarGuyBruno

Ай бұрын

@@HVAC_Mechanic I agree . Something is throwing off a/f.. just unsure what..

@HVAC_Mechanic

Ай бұрын

A Rich condition can be hard to troubleshoot but it seems to be something affecting the whole engine like a stuck open purge valve. If you think it is a bad injector, remove the spark plugs one at a time, and match them to a spark plug burn chart and see if a cylinder is running Rich.

@TimeLapseCarGuyBruno

Ай бұрын

@@HVAC_Mechanic I'll have to locate the Purge valve.. 2008 Suzuki sx4

@TimeLapseCarGuyBruno

Ай бұрын

@@HVAC_Mechanic Update.. I checked all spark plugs, coils, injectors.. all check out fine.. misfire code has Gona away.. also did a smoke test for vacuum.leaks...saw nothing in the engine bay leaking.. checked cam sensor for resistance and continuity. Checked all sensors and harness plugs for resistance and continuity and faulty breaks in wiring.. all good... The only thing that I did off the cuff was removed the air box and cleaned it out.. seemed to be some debris .. also removed the MAF sensor and sprayed it with that crc cleaner.. air filter looks new.. cleared code and nothing has popped back yet... Could it have been a dirty MAF sensor being the culprit? Nobody ever mentions that as a possibility for P2097 in any YT video..

I have all cylinders misfiring ive replaced all spark plugs, fuel pump, fuel rail, fuel injectors, coils, and fuel relay im stumped it really only has trouble starting up but once its running i can turn it on and off no problem HELP

@Baileys.small.engine.repair

20 күн бұрын

Do you know what condition your catalytic converter is in? Also could there be a leaking intake manifold gasket?

In other words a Po300 code means prepare yourself for a trip to hell.

......