Thats cruel on that motor, he needs to read the starting instructions, glow plugs for 2 or 3 mins depending on temp then when it fires go back to glow plugs till it runs smooth, no need for all the smoking an knocking going on there.
@johnnoonan58029 ай бұрын
What a great starter motor ,, pity the glow plugs arent as good theres alot of diesel in the cylinders there easy to break a con rod , the Cummins starts a bit easier ,, the D 9 g and H are great dozers though
@danielcapo19916 ай бұрын
I don’t recommend you use an ether because it can ruin bearings in engine
@RomeKG4712 жыл бұрын
Get the glow plugs working! Good way to throw a rod!
@ruaraidhmcdonald-walker952410 ай бұрын
Or alternatively use the preheat for a minute before cranking as you’re instructed to do….. 🙄
@jimwise4029 Жыл бұрын
Heat with glow plugs for 2 minutes should fire ride up no need for for your can
@NC-xk1eg5 ай бұрын
I can't believe that the battery had that much juice!
@MailsonJaques8 ай бұрын
Has it always been like this since the factory starts?
@chrismurnane638911 ай бұрын
Piolet motor is the ONLY WAY in my obstinate option 😊
@austinshackles549
25 күн бұрын
Only the old ones had pony motors, I think. Newer ones are electric start. I had a diesel van once that took 90 seconds of preheat to start in cold weather, any less it wouldn't fire.
@gearhead99433 жыл бұрын
Please make more of these but next time bring us closer so we can watch what you do with the controls and pedals while starting it
@ColtWR
3 жыл бұрын
Will do
@skanti-sp2qz5 ай бұрын
Bet the valve clearances are way out of spec.
@shanemurphy2680 Жыл бұрын
I've got a fiat allis fd40 touch the starter putting and it off,runs so smooth ,cummins kta19,there prehistoric cat engines when they eventually Start are so dam rough
@jimwise4029
Жыл бұрын
Might start good but how long does it run before it throws a final drive
@franko379210 ай бұрын
Pull the choke lever
@waldotrueb6081
10 ай бұрын
More choke !
@unclejoe79293 ай бұрын
No one ever taught him how to use ether properly. If I saw him do this to one of my machines it would be the last time he ever sat in one. Now if no one has taught him, ok, lesson Number One DON’T do it this way. You spray the ether into the air intake WHILE you are cranking it! NEVER spray and walk away.
@austinshackles549
25 күн бұрын
better yet don't use it at all. If the preheat doesn't work, it's not that hard to fix it. Too many folks just reach for the ether. I guess it's legit if you're trying to start something that's been sitting for 10 years but anything that's run at all regularly ought not to need ether.
@nspro931
24 күн бұрын
@@austinshackles549 What he did on this big motor is no problem at all.
Пікірлер: 21
Thats cruel on that motor, he needs to read the starting instructions, glow plugs for 2 or 3 mins depending on temp then when it fires go back to glow plugs till it runs smooth, no need for all the smoking an knocking going on there.
What a great starter motor ,, pity the glow plugs arent as good theres alot of diesel in the cylinders there easy to break a con rod , the Cummins starts a bit easier ,, the D 9 g and H are great dozers though
I don’t recommend you use an ether because it can ruin bearings in engine
Get the glow plugs working! Good way to throw a rod!
Or alternatively use the preheat for a minute before cranking as you’re instructed to do….. 🙄
Heat with glow plugs for 2 minutes should fire ride up no need for for your can
I can't believe that the battery had that much juice!
Has it always been like this since the factory starts?
Piolet motor is the ONLY WAY in my obstinate option 😊
@austinshackles549
25 күн бұрын
Only the old ones had pony motors, I think. Newer ones are electric start. I had a diesel van once that took 90 seconds of preheat to start in cold weather, any less it wouldn't fire.
Please make more of these but next time bring us closer so we can watch what you do with the controls and pedals while starting it
@ColtWR
3 жыл бұрын
Will do
Bet the valve clearances are way out of spec.
I've got a fiat allis fd40 touch the starter putting and it off,runs so smooth ,cummins kta19,there prehistoric cat engines when they eventually Start are so dam rough
@jimwise4029
Жыл бұрын
Might start good but how long does it run before it throws a final drive
Pull the choke lever
@waldotrueb6081
10 ай бұрын
More choke !
No one ever taught him how to use ether properly. If I saw him do this to one of my machines it would be the last time he ever sat in one. Now if no one has taught him, ok, lesson Number One DON’T do it this way. You spray the ether into the air intake WHILE you are cranking it! NEVER spray and walk away.
@austinshackles549
25 күн бұрын
better yet don't use it at all. If the preheat doesn't work, it's not that hard to fix it. Too many folks just reach for the ether. I guess it's legit if you're trying to start something that's been sitting for 10 years but anything that's run at all regularly ought not to need ether.
@nspro931
24 күн бұрын
@@austinshackles549 What he did on this big motor is no problem at all.