6:16 inserting tennis balls. 9:25 riding it

@damuryder9985

5 жыл бұрын

danny Dts thanks

@phoenixarebalo3108

4 жыл бұрын

Thx

@Albert-eu8iw

3 жыл бұрын

Thx

That impact gun is clapped out

@dillionbrown7865

5 жыл бұрын

BUT! its still clappin...

@RotaryCrossType7

5 жыл бұрын

The compressor doesnt have enough pressure.

JoeyMac420 runs nothing but imported tennis balls in his rear tire.

@bigspoops7228

5 жыл бұрын

They need to be imported thats the most important part.

@RotaryCrossType7

5 жыл бұрын

Na it's just what comes from the dollar store. They are cheap cheap cheap. Because the tennis balls wear out after a while.

@janellemcdonald1864

5 жыл бұрын

Yes

@benjamin9306

5 жыл бұрын

Seriously? I don’t know if you are being for real

@rudieolivier9784

5 жыл бұрын

Je help I want wan plese

The clapped rear hub😅😂 Never seen the tennis ball hack before

I used to work at a shop. Putting a piece of cardboard on the ground (so you don’t mess up the rim and hub) and kneeling on the tire and using your knees to keep the bead pushed down makes it WAY easier. Especially on the smaller tires. They also don’t try to run from you. I used to be able to do it faster on the ground than with the rack

Ima let it warm up, (moments earlier) Braaaaaap!BRAAAAP! Brap Braaaap!

When changing tires you always keep the opposite side in the drop center then the tire will slip on like a glove you’ll never struggle again

@kauaisfinest14

5 жыл бұрын

That Baby Shark GTO you do realize that you can still get it in with the tennis ball idea? And that the ball is round so that’s what give you space to access the drop center. Also I have a tubliss system on my bike the center bladder takes up the entire drop center but yet you can still squeeze it enough to get it in there

@conspiracy_0011

5 жыл бұрын

What a saint🙏

Whenever i change tires I found its best to put both the new tire and the old one on the rim out in sun so they get warm makes taking the old tire off the rim and putting the new one on easier

Love ur videos🤙

The mx32 is a track tire its gonna wear out super fast for how much street riding you do.next time get the mx52

@conspiracy_0011

5 жыл бұрын

Dunlop mx52? Asking because that's what I got recently for mostly dirt riding but occasional street

@bwbailey12

5 жыл бұрын

@@conspiracy_0011 mx52 is a harder compound that rates intermediate to hard and it will last longer if you ride on road sometimes. But there is better tires for road use.

@conspiracy_0011

5 жыл бұрын

Awesome thanks man

Use a bead buddy when putting the tire back on helps keep the bead from popping off and puts pressure to button the tire up a lot easier

Been waiting on this

That’s sick never thought it would actually work, when’s the next build video?

For that bolt you tried to get loose with the impact. Take your longest ratchet and put a piece of metal tubing over the handle (jack handle will work) and pull as hard as you can. Normally works better than any other method.

@charlesgunzelman3323

5 жыл бұрын

Double and triple check it's a standard thread and not left/reverse thread!

I’ve actually put racket balls in my Honda 50. Works surprisingly well!

It takes air pressure to keep tire from spinning on the rim, doubt the wedge in rim will be enough to hold it for long.

@tsuzukimurphy64

Жыл бұрын

Rim lock

Hey Tyler can you recommend an LED light bar package for a klx110? Got a link to drop? Wiring, bracket, switch all in 1 preferably

Lol great vid man just recently got back into riding bought 2 months ago I'm 14 and started back after 4 to 5 years without riding and started back on a Yamaha ttr 125 but am looking to upgrade to a small wheel 250 or a 2 stroke 85 and one question what is your favourite moto gear brand I'd say personally Thor or one oneil.

Do a build on the pitter

With new tires set them set against or near your furnace for about 2 hrs

Hi tyler. I seen you having troubles with that cross threaded bolt in the honda crank. Since the crank is burnt why not cut the head of the bolt off. Or use a j bar with a big pipe. Just a suggestion

Where did he get that blue & black tmmx wrap from??

That would be perfect for studded tires too.

I’ve a 125 pit bike 12 inch back wheel and I replaced the tube with pipe insulation I got for €1. It’s hard enough and does the job but occasionally the rear wheel rims spins within the tyre. Front wheel is grand. Any suggestions to stop this spinning?

Love this channel man

Maybe you could press in a smaller bearing with the Same inner diameter. And then just use the old bearing with the broken inner hub as a spacer. Just as a temporarly fix

It’s hard to tell which pit bike had more problems your old black one or this one😹

@Jacksonflax

5 жыл бұрын

@Izzy rod Be gone.

That's kind of cool do you think it'll work for an SSR 125 I can't get the tire rim lip to seat in the rim. Thinking about a blowtorch to soften up the edges. Some people say leave your tire out in the sun that well softens up. The bike is just sitting there with a cracked frame needing a new chain 420 and a Kickstarter

Using soap and water on the bead of tires also make it so much easier to change especially installing

I've always wondered about this. I know Moose Racing made a T.ballish similar product back in the day that had mixed results. Thanks, I need a ride change on the pit bike soon anyways.. I also have a bunch of tennis balls....

I have a 2015 kx250f and my launch control button is not working and I was wondering if you could help me.

Did you try pouring oil in the hole that the compressor connects to

3:50 yep you definitely snapped it... surprised it snapped cause I’ve jumped my klx 110 5-6 feet jumps on to pretty much flat ground, all on the back wheel, and that’s never broke, so there’s no telling how much that bikes been through. 🤟🏼😂

Great video!!!

At the end of getting the bead back on, the pain in ass part, use a c clamp opposite the pain section and push in towards hub. It buys just a little bit.

Where did. You get the kx 125 they don’t make them anymore

@lukeseiler5799

5 жыл бұрын

Christopher McBain he built it from a 03, he has a playlist

@christophermcbain270

5 жыл бұрын

Did he use 250 plastics because 125 and 250 are pretty much the same thanks

@eastonwarf5744

5 жыл бұрын

Christopher McBain I’m pretty sure he used 250f plastics and a 3D printed conversion kit to fit them , it’s all in the kx playlist though

1 get impact rated sockets . 2 get a better compressor or adjust yours for more psi mate

You are cool with your dirt bike

You should try it on the 250

I have done it to the yamaha yz450and it works great almost 2years

@henrik7966

5 жыл бұрын

have u had to change the tennis balls from wearing down?

@kristerssprogis4165

5 жыл бұрын

@@henrik7966 no it works great

I wonder if the rear wheel cracked from not tightening the rear axle enough. Cause it looked pretty loose in the video, but probably cause it’s already cracked lol. Idk.

If I get bigger tires for a dirt bike do I have to get bigger rims

I wonder if that would be safe to use on a yz400f

This video is dope

I've bought 9 tubes and all had same problem and my Honda dealer said there not recommended after the fact like wtf would u sell them to me 15 bucks a pop but I thought of tennis balls so thx for the vid so I could see what happens before I waste more money

Way back when we screwed the bead to the rim. I ran a 4.50 x 18 6 ply Cheng Shin Desert Knob on my Husky 400 Cross at 2 psi in soft stuff Never more than 6 psi on the hardest packed dirt.

Hey Tyler. Do you run 110 in your 250f?

Has any one els done this are there any problems with the rim spinning inside the tire?

You an donit on a big bike.. I have ran them in the front tire on my 250.. works well and feels like 12ish psi..

Ohh I see thanks dude

You got balls to do this😂😂

Gonna try that today

whats your opinion on the kawasaki kx125 08 model

I need to get that portable jump starter, I’m way to weak to push my 250 outta the trails if my battery died. Knock on wood hasn’t happened to me yet.

Could the bolt be left hand thread? Meaning u needa screw it to the left

@jessehobart2899

5 жыл бұрын

That's the first thing he mentioned in the video and he said that it is not reverse threaded.

use some soapy water when reinstalling a tire. less struggle

Do a build on your pit bike

Expanding foam tyre works bestb

What exhaust are you running???

How long did the tennis balls last

Are they left handed threads?

Nice work is this still working for you?

Are kenda tires good for pit bikes

doesn't the tire spin on the rim without a rim lock???

But how’s it do jumping ? An with a rider over 200 pounds

I'm going to try this on my 1984 ds80 because I keep popping tubes

Tyler lover your videos. I ride also I have 110 klx kawasaki and a 115

Was this tire an 80/100-12?

U should get new chain and sprockets for pit bike

What about no rim lock and tire spin?

Tire: Tyler: you will never be the same again

What year is your kxf?

Try some anti seize on that bolt and use some heat at the same time

The great thing about this is that I don’t think tennis balls pop or go flat if they get punctured!

@niklasalmaas6369

5 жыл бұрын

Eddie Vega they pop under too much pressure, and get wayyyy too soft when punctured

Shit looks legit to me. Go for it !

That bolt that wont come out of the case could have reverse threads?

@jessehobart2899

5 жыл бұрын

Did you not listen to the video, he said he did the research and it is not reverse threaded...

wouldnt the tyre spin because no beadlock?

@southernracing2468

4 жыл бұрын

SIR PAUL a little bit but it’ll spin anyways with a tube and that’s what kills tubes

handballs or racquet balls may work too

Sick pit bike build next??

bro you have the same prob wen i had to take my crank off the case it would not come off but we found it it was opisit fred EDIT i took apart this 1990 kx80 once to get the crank out it just had a C clip not a nut wich i wish today these bikes have C clip it would just be so much more easy

@honda8192

5 жыл бұрын

My 83 kx80 had a bolt on the water pump gear

@dirtmachines4253

5 жыл бұрын

Honda same but that one came off with ezzz but it was just the crank bolt won’t come off

Use soap and water to make the tire slide on and off easier

Another trick is to get a vice and put a bar or steel shaft in it, cinch it down, now put the wheel on it like an axle and now you have a leverage point. Oh and break the bead on the tire first too.

Exhaust name please ?

I had to pause the video when I seen that impact attemp. Just a friendly FYI any air impact requires somewhere around 5cfm at 90 psi that cute compact compressor ain’t gonna do it you’d probably get more power out of your hand then with that impact

@benson4u215

5 жыл бұрын

Even my 17gal compressor can only take a few mins between inflations lol

Yes

how about foam along with the balls?

@canamcrazyman9301

5 жыл бұрын

J D like this can foam to fill up the gaps or maybe just the balls connected to the tire with the foam 😂

Turn the air tool to the opesit side

What size wheels

I have done it and It went well

Remember back in the day when Joey Mac said he did this? Now it’s actually a reality!

U should get a klx140 or klx140L if u get the 140 get the shock off the klx140L the rear shock it’s adjustable

@Yzj-nq8cl

5 жыл бұрын

Matt Jones u gotta comment gay shit every vid

That rim has a bend on the right side of it to

Great hack

the screws are suppose to inserted from the inside of the tube

Awesome 😂

Hey bro can you send me a full pit bike exhaust

My 110 hub did the same thing

Hi my birthday is July 31 and I want a kx100 or quad I want a quad when u covered the tires with tape that quad but I can not get it my mom have to pay the bill and it is real out here that my dream to have a dirt bike and u doing good with your chennel u keep it up I try to save my money but I have to help my mom I do not need it but it is my dream and never give up

A donut spare from any 14 inch car tire without any air. Sucks to put it on but works perfectly and lasts forever

Hagart garage 😂 😂 😂