m.vevor.com/ultrasonic-cleane... m. groups/8644363... bellhoppers-apparel.creator-s... Jeremebell11@gmail.com
Жүктеу.....
Пікірлер: 17
@famasmaster20009 ай бұрын
Very well done Mr Hopper 👍🙏
@HallnoutMhall9 ай бұрын
Good morning/night buddy.
@PatrickFlagg-ys1lx9 ай бұрын
That saw sounds way better then the last time I heard it run at smitty's. Wonder what caused that cylinder to act like that? Good job hopper
@stoickthevast22189 ай бұрын
I gotta get my 395 out to you man that looks amazing
@michaelwhiteoldtimer76489 ай бұрын
Great job
@nateolmsted8999 ай бұрын
Love it
@wimkool38089 ай бұрын
Sounds great!
@wayneanderson9919 ай бұрын
Hi Bellhopper, I wonder if there might be some rust developing in the muffler as the saw sits and then it's being sucked into the cylinder when running the saw thus scoring the piston . I have also seen mufflers that are opened up like that one is with the short straight forward ports , in dusty storage environments (work shops, open storage shed's) can collect particles in the muffler and over time that gets ingested into the cylinder.
@kurtsteele55879 ай бұрын
How's the Hoppers
@thetwostrokerebuilder9 ай бұрын
Use a burr or stone to grind off plating first then it won't chip 🔧🔧
@lehibell61769 ай бұрын
High spots in Chrome or bore out of round perhaps?
@crazyfeller57049 ай бұрын
👍👍
@Daniel-md7um9 ай бұрын
Mais quel bordel sur l’établi!
@travistoth88349 ай бұрын
Love the videos Quick ? How important is ring gap and what’s a good gap on a 55 husqvarna
@joeygordon47999 ай бұрын
That pain in the butt his never ran that good and thanks buddy also all that wear is from less than a 45 minutes of run time
@JandKPowerSawz96929 ай бұрын
I guess we gonna have to send our 385 to you we can’t figure out what’s wrong with it got a brand new carburetor an it still won’t run
@grayhawk-bh6bw9 ай бұрын
I knew the titanium coated hyway cylinders were tough to grind. Is the normal ones hard to grind also?
Пікірлер: 17
Very well done Mr Hopper 👍🙏
Good morning/night buddy.
That saw sounds way better then the last time I heard it run at smitty's. Wonder what caused that cylinder to act like that? Good job hopper
I gotta get my 395 out to you man that looks amazing
Great job
Love it
Sounds great!
Hi Bellhopper, I wonder if there might be some rust developing in the muffler as the saw sits and then it's being sucked into the cylinder when running the saw thus scoring the piston . I have also seen mufflers that are opened up like that one is with the short straight forward ports , in dusty storage environments (work shops, open storage shed's) can collect particles in the muffler and over time that gets ingested into the cylinder.
How's the Hoppers
Use a burr or stone to grind off plating first then it won't chip 🔧🔧
High spots in Chrome or bore out of round perhaps?
👍👍
Mais quel bordel sur l’établi!
Love the videos Quick ? How important is ring gap and what’s a good gap on a 55 husqvarna
That pain in the butt his never ran that good and thanks buddy also all that wear is from less than a 45 minutes of run time
I guess we gonna have to send our 385 to you we can’t figure out what’s wrong with it got a brand new carburetor an it still won’t run
I knew the titanium coated hyway cylinders were tough to grind. Is the normal ones hard to grind also?