Install cam bearings on 5.7l HEMI. Also talk about getting the old ones out.
Жүктеу.....
Пікірлер: 9
@erichorne6466Ай бұрын
Great video . Bottom line do not use the aftermarket grooved bearings unless you clock them in between 1 and 330. The measured spacing on both sides was nice
@Hillbillygarage1215
Ай бұрын
Thank you for visiting Eric. I am very happy with the way the clocking has turned out. I have great oil pressure and my trucks are running great. We look forward to seeing you back at Hillbilly Garage.
@Coach_Vince2 ай бұрын
Good job 👏 you’re much more patient than me!
@Hillbillygarage1215
2 ай бұрын
Thank you for checking in with Hillbilly Garage. Hope to see you back soon.
@mikethomas124511 күн бұрын
Nice Job! Doing this at the moment. Your video help me alot.
@Hillbillygarage1215
11 күн бұрын
@mikethomas1245 thank you for sharing. It's exciting for me to know I've been able to help someone. What exactly are you working on? How deep of a build is it?
@mikethomas1245
8 күн бұрын
@@Hillbillygarage1215 I'm working on the same engine you have 5.7 Hemi. When i bought the truck it has a little over 200,000 miles on it. don't know when the last oil change was. So I changed the oil and and drove it about 100 miles and spun a cam bearing and seized up and snapped the timing chain gear bolt that holds it to the camshaft. So I'm doing a full rebuild.
@Hillbillygarage1215
8 күн бұрын
kzread.info/head/PLVs8K55GyL-r5BRkWAxB5J1L0SxFhTlab&si=SwNYbwylcumYDRZj There are a few tips in this video link that might be helpful on your HEMI project. Be sure you pull all the oil galley plugs out and flush the entire oiling system
@Hillbillygarage12152 ай бұрын
kzread.info/dash/bejne/qKGixaaGYri1oNo.htmlfeature=shared This is the link to the Playlist on the whole journey on the #8 misfire on my 5.7 hemi
Пікірлер: 9
Great video . Bottom line do not use the aftermarket grooved bearings unless you clock them in between 1 and 330. The measured spacing on both sides was nice
@Hillbillygarage1215
Ай бұрын
Thank you for visiting Eric. I am very happy with the way the clocking has turned out. I have great oil pressure and my trucks are running great. We look forward to seeing you back at Hillbilly Garage.
Good job 👏 you’re much more patient than me!
@Hillbillygarage1215
2 ай бұрын
Thank you for checking in with Hillbilly Garage. Hope to see you back soon.
Nice Job! Doing this at the moment. Your video help me alot.
@Hillbillygarage1215
11 күн бұрын
@mikethomas1245 thank you for sharing. It's exciting for me to know I've been able to help someone. What exactly are you working on? How deep of a build is it?
@mikethomas1245
8 күн бұрын
@@Hillbillygarage1215 I'm working on the same engine you have 5.7 Hemi. When i bought the truck it has a little over 200,000 miles on it. don't know when the last oil change was. So I changed the oil and and drove it about 100 miles and spun a cam bearing and seized up and snapped the timing chain gear bolt that holds it to the camshaft. So I'm doing a full rebuild.
@Hillbillygarage1215
8 күн бұрын
kzread.info/head/PLVs8K55GyL-r5BRkWAxB5J1L0SxFhTlab&si=SwNYbwylcumYDRZj There are a few tips in this video link that might be helpful on your HEMI project. Be sure you pull all the oil galley plugs out and flush the entire oiling system
kzread.info/dash/bejne/qKGixaaGYri1oNo.htmlfeature=shared This is the link to the Playlist on the whole journey on the #8 misfire on my 5.7 hemi