The cars corrected mph is 116 at 6000 rpm in 4th gear with a 28 inch tall tire and 4.30 rear gears. Looks real fast tho!

@TurboTurdBurglar

3 жыл бұрын

Yeah he definitely had some people fooled

did you run 4-4.5 seconds 0-60mph? what time do you run in the 1/4 mile?

Any engine mods other then pi swap?

What's cam any other mods

Why is your temp pegged on hot?

@clarkmiller287

7 жыл бұрын

John Quinlan it's disconnected, the ECM temp sensor is plugged in but the one for the cluster runs to a A-Pillar gauge

What cam do you have just stock one that came with pi heads?

@Xxcody3232xX

4 жыл бұрын

Did you have to do the 4° because the valve clearance issue ?

que motor tiene

my 98 pi swap compression is everything. a later gt 2v with 4.10s an your basic mods CAI, longtubes, x-pipe, slp1's can't keep up. if when you do a pi swap and your doing it, polish off your pistons. makes the car run a bit better. with the 98 short block and a piston polish an a set of pi heads with a shave on the aluminum studs that are next to the valves. it's a cheap machining job, you will get your compression to 10.7 witch is perfect for a all motor build. light weight flywheel (16lbs) an aluminum driveshaft with 3.55 for max topend mph. with that type of compression stock 3.27s feel like 4.10s in a 04 gt. with a Cam that revs too 6200 an a Pro Comp aluminum intake from EBay an prefesional product plenum an 75mm TB + 1" helix spacer for TB and Intake. EGR delete + A\C delete, underdrive, electric water pump, 30lb injectors with the 86mm MAF. stock internals for block and heads. now the intake and plenum have casting imperfections so take a dremmal tool(same you should use to polish your pistons) an polish away all imperfections. put a avator fuel pump in it. soo yeah bottom line 410hp to the wheels, alll motor right there. works best with a 98 block

@crowleyop5863

7 жыл бұрын

Flailing Mantaray I'm actually about to start a pi swap build right now just got a donor block in today this is some good advice sounds like a nice build I'd love to have this

@DickVanNiggz

7 жыл бұрын

Flailing Mantaray idc what you do you're gonna need waaay more than a damn pi swap to make 410 crank with a 2v 4.6, let alone 410 wheel lmao what'd you forget to mention the 100 shot? 😂

@garydaltonIII

6 жыл бұрын

Flailing Mantaray mine 2v is running 12.1

@aaronmcalister3513

6 жыл бұрын

Richard Skipper that’s defiantly a lie lmao

@rayman1230

6 жыл бұрын

@@aaronmcalister3513 it surprises me how many people don't know how to build an engine to it's full potential. There's engine math for a reason. It's not like 2v s are immune from it lol. Raise compression, let the heads breath, and match the cams to maximize the setup. There NO Reason a 4.6 should not be able to put dowm 400rwhp.

so when are you going to calibrate the speedo

@clarkmiller287

10 жыл бұрын

It is, 23T gear and a 28" tall tire. It was usually a mph or 2 within my GPS

@whiteoakproud7882

Жыл бұрын

No it's not....

@NerdKrusher

10 ай бұрын

I have a similar setup for my 96 gt. Can confirm, they are this fast when tuned right. I’ve pissed off a lot of other guys who thought they were the shit. Charger rt, 392, c8 vett, these 2v are nothing to screw around with.

@Mach_bro

8 ай бұрын

⁠​⁠@@NerdKrusherrt yea but your probably not beating a scat unless the driver has the iq of a 12 year old same with vette

Very Nice build man, check out some of mine too! Just another gear-head

Is coolant overheating?

Looks like u on e

check your coolant temp dude...

@clarkmiller287

6 жыл бұрын

chaki83 it's disconnected, I'm running an Autometer guage on the A pillar

That must be one hell of a downhill slope.

@jaystol7988

6 жыл бұрын

read his reply to yellowmach1's question

@jaystol7988

6 жыл бұрын

and at 2950lbs

I have a 4.6 npi with pi heads and im running 270ah comp cams. I just installed them. I dont seem to have any clearance issues. Should i he worried. Can i degree them without ajustable cam gears ?

@madmod

4 жыл бұрын

Go adjustable crank gears from tfs.

@Xxcody3232xX

4 жыл бұрын

@@madmod not the issue tho should still run/build compression

@Xxcody3232xX

4 жыл бұрын

I got anwsers already. When i did the timing i must have done it wrong some how. I have like 0-30 psi each hole

@madmod

4 жыл бұрын

@@Xxcody3232xX ouch. Hopefully you didnt hurt any valves in the process.

@Xxcody3232xX

4 жыл бұрын

@@madmod dont think so i pulled the heads twice now

Yea that the craziest acceleration I've seen on a pi swap with cams, what are the other mods? Cause if all you have is a cam that's crazy...

@clarkmiller287

10 жыл бұрын

Car weighs 2950lbs and has 4.30's with a 28" tall tire

@ParkerBuhrman

7 жыл бұрын

I know this is old.. but what did you do to achieve 2950lbs??

did you have any ticking after pi swap?

@clarkmiller287

8 жыл бұрын

Nothing, ran fine.

@timcheaney2110

8 жыл бұрын

Mine is ticking bad

@clarkmiller287

8 жыл бұрын

+Tim Cheaney probably a lash adjuster or chain guide.

@timcheaney2110

8 жыл бұрын

+ZRX_café they're new

@timcheaney2110

8 жыл бұрын

+ZRX_café I have vids up

why does it rev to like 7 k. my bullit revs to 6

@clarkmiller287

9 жыл бұрын

It's got a tune. I set my limiter to 7100. The cams helped a good but it still started to run out of steam around 6200. The gears and higher compression helped a lot though

@madmod

4 жыл бұрын

Bullit intake really works at the same rpms as a stock pi, albeit with a few extra ponies.

Pi swapped that's it?

@madmod

4 жыл бұрын

Comp 270s

That thing is bas ass what kind of exuast

Gears with no speedo correction....nice try though