Just got my Chevy tracker today and I am going to be using your videos to help me whip mine into shape.

@trashpandaoffroad3548

3 жыл бұрын

Great to hear. Good luck. Let me know if I can help. Keep watching the channel got lots of projects happening and another build project starting soon.

Great video. When u install seals like this only put oil on the ID of the seal. On the OD put “Bearing Mount” to prevent it from coming loose. Great job, your explanations are easy to follow.

@trashpandaoffroad3548

Жыл бұрын

Never heard of bearing mount. I will look into it.

Good video. Thanks for sharing!

@trashpandaoffroad3548

4 жыл бұрын

Thanks for watching and commenting. Hopefully it helped you in some way.

Right now though it idles at about 2500 rpm. At higher rpm will you be able to tell if its off time like that? Going down the road it sounds smooth. But sitting it sounds rough. It idles so high I think because my alternator doesn't have a belt on it. It was shredded

Thanks for sharing!

@trashpandaoffroad3548

3 жыл бұрын

Hope it helps.

Hey man, great vid. Do you remember what you think might have caused the timing to misalign? The camshaft turning a bit? Or the belt's teeth not put back on exactly? Maybe belt fell off crank gear below and got put back on differently? Im about to try this exact thing on my Toyota 😬

@trashpandaoffroad3548

3 жыл бұрын

I think belt skipped over a little while I was trying to tighten it. Probably would have been a.good idea to have someone watch everything as I tightened it down.

Your car sounds like mine when you cranked it after your belt was put on the first time. I'm thinking mine may have jumped a tooth as well. Its got 200k miles on it and I don't know if belt has ever been changed on it.

@trashpandaoffroad3548

3 жыл бұрын

If your gonna look into it check the lower pulley. The key way tends to go out and effect timing.

hello, why on minute 3:00 aprox, you turn the gear to the right and on 3:40 you turn the gear to the left?

@trashpandaoffroad3548

4 жыл бұрын

I move the gear to the right in order to get the whole assembly to a point where I can put the screwdriver all the way though to stop the gear from spinning when I go left

I have a Geo tracker 95, in minuto 4:01 where you removed the pulley, where the dot is? E or I?

@trashpandaoffroad3548

2 жыл бұрын

I wish I could remember. I dont think I set the engine to TDC I just marked it and lined everything back up.

is the camshaft seal same size as the crankshaft seal

@trashpandaoffroad3548

9 ай бұрын

That I do not know. They look similar but I don't know if they are the same.

Dude, you are supposed to press in seals, not hammer them in. You run the risk of the seal spring falling off. That seal bore seemed loose. You should have used some sort of sealant such as Locktite 510 flange sealent.

@trashpandaoffroad3548

4 жыл бұрын

Thanks for the tips. I am just learning as I go. I didn't know loctite made a gasket sealent.

Hello can You support me with the position of the axle gear, I Lost the sequence ,thanks!!

@trashpandaoffroad3548

3 жыл бұрын

There should be a small dot on. The gear that you can use to line it back up with.

can i doit on honda civic 94 myself

@trashpandaoffroad3548

3 жыл бұрын

I dont know how mechanic you are and I dont know anything about honda motors but if you keep all the timing points lined up it shouldn't be to difficult. I think.

No puedo quitar la bomba de pawer

Where is the cam shaft sensor located on this vehicle?

@trashpandaoffroad3548

4 ай бұрын

I believe that one is on the back of the engine under the transmission bell housing.

@zachary4225

4 ай бұрын

@@trashpandaoffroad3548 thank you. My dad had the engine overhauled and now it’s not starting. He’s checked everything, I told him I think he has to drop the transmission to check that sensor. I just wanted to confirm. Thank you.

@zachary4225

4 ай бұрын

@@trashpandaoffroad3548 you mean inside the transmission by the flywheel or just unDer the transmission ?

@trashpandaoffroad3548

4 ай бұрын

Once you separate the transmission and engine it will be above the flywheel kinda below thw distributor

@zachary4225

4 ай бұрын

@@trashpandaoffroad3548 ahhh ok. Thank you

Camshaft seal* Good video anyways!

@trashpandaoffroad3548

4 жыл бұрын

Thanks. I know what I mean but have been calling it wrong all week. It sounds right in my head.😊