Looks worse than it is. It’s not too bad. Good luck. 👍🏻
@c1nicolei3 ай бұрын
So thankful for videos like this. Will be a huge help when I do this on my 68! 😊
@ratfarm767
3 ай бұрын
👍🏻 Good luck on that 68!!
@nickg14492 жыл бұрын
The brackets are for the tray that holds the rear window storage.
@gspistole9762 жыл бұрын
Thanks for the recording. I've got carpet ordered for my 69. I've never done a carpet install. Learning experience...
@ratfarm767
2 жыл бұрын
It’s not too bad. The front is a lot easier, they just plop right in and cut around the bolt holes for the seat and that’s about it. Good luck 👍🏻
@ST-qe6pp Жыл бұрын
I gotta do this. Carpet is in the box. Thanks for posting!
@johngreenwood6813 Жыл бұрын
The brackets are for a fold down lid where your removable rear windsceen glass goes When you have the tops off and your rear glass comes off as well There are 2 latches on the top inside of your rear glass to release the glass out
@patspagnuolo8471 Жыл бұрын
Thank You for making this video I had no idea where to start. I have a 1975 Convertible and it was missing all of the interior when I got it.
@ratfarm767
Жыл бұрын
I went through the same ordeal, the car was a bare shell when I got it. Pretty much approached all these projects with the “wing it” method. Happy to hear this video helped you out. 👍🏻
@mrdasilvaf Жыл бұрын
Appreciated the video, about to mine as well 👍 great job!
@MDJNope2 жыл бұрын
I believe the brackets are for the tray that stores the rear window when you take it out.
@ratfarm767
2 жыл бұрын
Hmmm, didn’t even know they had that. I’ve had 9 or 10 C3’s not a single one has ever had that tray. Thanx! I’ll have to look into it.
@travisbullock5660
Жыл бұрын
This is correct. There’s a tray for the glass when it’s removed from the window hole.
@dennisdillman4865 Жыл бұрын
Great video, just did mine and that light is a SOB...even though i had old carpet. One thing i would ad is to precut useing old carpet as template and use some masking tape to mark holes like for the rubber plugs and light screws locations.
@ratfarm767
Жыл бұрын
Thank you! Absolutely, great piece of advice for anyone doing this project. Unfortunately I didn’t have any carpet to use as a template which made it a real bugger to install.
@clevewallace4026 Жыл бұрын
Thank you so much for making this video. This helps a lot.
@ratfarm767
Жыл бұрын
Pleased to hear it’s helped you out, makes doing these videos worth it 😁
@jessemarinjr6374 Жыл бұрын
Thanks for the Video !! Great Job!!
@ratfarm767
Жыл бұрын
😁
@BPattB Жыл бұрын
Just yesterday we did the back half of a 71 Corvette. By far the worst for us was the wheel wells. Unless you're putting relief cuts in you're going to have lumps and bumps.
@johngreenwood6813 Жыл бұрын
The brackets are for the rear glass carrier to store the rear glass when it’s removed it fits in a storage tray out of the way
@thedrivewayC32 жыл бұрын
Thanks - I’ll be doing mine in a month or so. Appreciate the tips
@thedrivewayC3
Ай бұрын
Updating my comment from 2 years ago! NOW - I’ll be doing mine in a week or so! 😂
@ratfarm767
Ай бұрын
@thedrivewayC3 better late than never 😀. It’s definitely a “wing it” kinda job, just get in there and hope for the best. Don’t forget to embrace your inner contortionist, it’s a tight squeeze. 👍🏻
@thedrivewayC3
Ай бұрын
@@ratfarm767 It is tight for sure, but I think it “might” be a little easier with a convertible. We’ll see…
@ericsmith4982 жыл бұрын
I'm working on a 69 with a removable rear window and it's for a storage tray
@jamescasello8100 Жыл бұрын
Looks great. Perhaps spray paint the inside of the storage boxes before laying your last layer of carpet
@garybryden55364 ай бұрын
Brackets are for the tray that holds the rear window when it is removed
@rustyshackleford33698 ай бұрын
It’s actually recommended to not glue the carpet in C3s, the carpet was not glued from factory, I can see having to do it over the wheel wells, but the carpet will relax and form where it’s put after a couple weeks
@SteveV62062 жыл бұрын
I am doing this exact same thing on a 74 c3 right now. I'll never touch one again. Talk about a pain in the butt!
@ratfarm767
2 жыл бұрын
Indeed it is. Overall the interior of these C3’s is nothing but a pain. Worth it when it’s done tho
@SteveV6206
2 жыл бұрын
@@ratfarm767 Your video has given me some motivation to finish everything up! I’m currently working on the rear carpet. I’m so worried about cutting it wrong!
@darrenmcsorley3726 Жыл бұрын
I have a 69 with all the original carpet still installed, so if you want some pictures or questions on how it all tucks in, just message back
@ratfarm767
Жыл бұрын
I appreciate that, interior is all done now. Sometimes you gotta wing it 😎
@thadiesel76559 ай бұрын
Thanks for vid. If I used dynomat, will I need additional carpet underlay? Or does the carpet come with the needed padding?
@ratfarm767
9 ай бұрын
You can buy it both ways, the carpet I purchased was just carpet with typical backing and I needed the padding but the more expensive carpet kits will have a rubber backing.
@debralgillette43512 жыл бұрын
How did u get carpet around thr back window xwvt drain tube?round
@debralgillette4351
2 жыл бұрын
I meant window vent drain tube
@ratfarm767
2 жыл бұрын
I removed the drain tubes and plugged them off for now, I need to order new tubes and drain vents. But when I do I’ll probably use a small razor like an Exacto knife to cut around them.
Пікірлер: 42
Getting ready to do this. Thanks for posting.
@ratfarm767
Ай бұрын
Looks worse than it is. It’s not too bad. Good luck. 👍🏻
So thankful for videos like this. Will be a huge help when I do this on my 68! 😊
@ratfarm767
3 ай бұрын
👍🏻 Good luck on that 68!!
The brackets are for the tray that holds the rear window storage.
Thanks for the recording. I've got carpet ordered for my 69. I've never done a carpet install. Learning experience...
@ratfarm767
2 жыл бұрын
It’s not too bad. The front is a lot easier, they just plop right in and cut around the bolt holes for the seat and that’s about it. Good luck 👍🏻
I gotta do this. Carpet is in the box. Thanks for posting!
The brackets are for a fold down lid where your removable rear windsceen glass goes When you have the tops off and your rear glass comes off as well There are 2 latches on the top inside of your rear glass to release the glass out
Thank You for making this video I had no idea where to start. I have a 1975 Convertible and it was missing all of the interior when I got it.
@ratfarm767
Жыл бұрын
I went through the same ordeal, the car was a bare shell when I got it. Pretty much approached all these projects with the “wing it” method. Happy to hear this video helped you out. 👍🏻
Appreciated the video, about to mine as well 👍 great job!
I believe the brackets are for the tray that stores the rear window when you take it out.
@ratfarm767
2 жыл бұрын
Hmmm, didn’t even know they had that. I’ve had 9 or 10 C3’s not a single one has ever had that tray. Thanx! I’ll have to look into it.
@travisbullock5660
Жыл бұрын
This is correct. There’s a tray for the glass when it’s removed from the window hole.
Great video, just did mine and that light is a SOB...even though i had old carpet. One thing i would ad is to precut useing old carpet as template and use some masking tape to mark holes like for the rubber plugs and light screws locations.
@ratfarm767
Жыл бұрын
Thank you! Absolutely, great piece of advice for anyone doing this project. Unfortunately I didn’t have any carpet to use as a template which made it a real bugger to install.
Thank you so much for making this video. This helps a lot.
@ratfarm767
Жыл бұрын
Pleased to hear it’s helped you out, makes doing these videos worth it 😁
Thanks for the Video !! Great Job!!
@ratfarm767
Жыл бұрын
😁
Just yesterday we did the back half of a 71 Corvette. By far the worst for us was the wheel wells. Unless you're putting relief cuts in you're going to have lumps and bumps.
The brackets are for the rear glass carrier to store the rear glass when it’s removed it fits in a storage tray out of the way
Thanks - I’ll be doing mine in a month or so. Appreciate the tips
@thedrivewayC3
Ай бұрын
Updating my comment from 2 years ago! NOW - I’ll be doing mine in a week or so! 😂
@ratfarm767
Ай бұрын
@thedrivewayC3 better late than never 😀. It’s definitely a “wing it” kinda job, just get in there and hope for the best. Don’t forget to embrace your inner contortionist, it’s a tight squeeze. 👍🏻
@thedrivewayC3
Ай бұрын
@@ratfarm767 It is tight for sure, but I think it “might” be a little easier with a convertible. We’ll see…
I'm working on a 69 with a removable rear window and it's for a storage tray
Looks great. Perhaps spray paint the inside of the storage boxes before laying your last layer of carpet
Brackets are for the tray that holds the rear window when it is removed
It’s actually recommended to not glue the carpet in C3s, the carpet was not glued from factory, I can see having to do it over the wheel wells, but the carpet will relax and form where it’s put after a couple weeks
I am doing this exact same thing on a 74 c3 right now. I'll never touch one again. Talk about a pain in the butt!
@ratfarm767
2 жыл бұрын
Indeed it is. Overall the interior of these C3’s is nothing but a pain. Worth it when it’s done tho
@SteveV6206
2 жыл бұрын
@@ratfarm767 Your video has given me some motivation to finish everything up! I’m currently working on the rear carpet. I’m so worried about cutting it wrong!
I have a 69 with all the original carpet still installed, so if you want some pictures or questions on how it all tucks in, just message back
@ratfarm767
Жыл бұрын
I appreciate that, interior is all done now. Sometimes you gotta wing it 😎
Thanks for vid. If I used dynomat, will I need additional carpet underlay? Or does the carpet come with the needed padding?
@ratfarm767
9 ай бұрын
You can buy it both ways, the carpet I purchased was just carpet with typical backing and I needed the padding but the more expensive carpet kits will have a rubber backing.
How did u get carpet around thr back window xwvt drain tube?round
@debralgillette4351
2 жыл бұрын
I meant window vent drain tube
@ratfarm767
2 жыл бұрын
I removed the drain tubes and plugged them off for now, I need to order new tubes and drain vents. But when I do I’ll probably use a small razor like an Exacto knife to cut around them.
@debralgillette4351
2 жыл бұрын
Rat Farm, thanks for responding.