Nice build video

Great video mate! The Iflight tune is so dialed! Happy Flying!

Such an awesome build, thanks for sharing!

Liked only becuase i love the the evoque v2 , its so nice i bought it twice :)

Very nice and beautiful build brother❤ when come video gps installation and programming

@benjedonethat

Ай бұрын

Working on it

Impressive stuff

Great build, thanks for sharing. Where did yiu get the air unit cable from? Did it come with the build?

@benjedonethat

26 күн бұрын

Yes it came with the air unit. But I have seen some of my local FPV shops to stock longer cables, so it should be available wherever you are.

could you proivde a list of all parts used in the build please?

Hello, congratulations on the video. A question, where did you buy the drone so that it can be disassembled? Because on all the pages or in the official one of the drone, it tells me that it is mounted and I want to ride it myself.

@benjedonethat

Ай бұрын

Hi, I also had some problems getting some of the parts but Iflights official website should have everything you need.

High mate, thanks for the build, question, the 20×20 fc and esc, i will be using m2 screws withe a mamba adapter to the mamba stack. ONLY IF THE M3 STACK SCREWS ARE NOT PART OF THE FRAME, ARE THE SCREWS PART OF THE LEGS OR ANYTHING, SO CAN I USE MY MAMBA ADAPTER?

@benjedonethat

2 ай бұрын

The m3 screws do keep the legs together, you can get shorter screws to just go through the frame and then get an adapter to m2 screws to mount your electronics.

Hey man! Great vid! Does the frame kit come with that buzzer/LED board thingy or did you buy it separately?

@benjedonethat

3 ай бұрын

Thanks man! It came with it and all the LED's

Can’t seem to figure out how to get my dji fpv remote v2 to show up on betaflight. And ideas?

@benjedonethat

8 күн бұрын

You have to pair them to your drone similarly to hom you do your goggles. Basically after you paired your goggles you do the same process again(hold the pair button on air unit until it blinks red) then power on your remote and then hold power button for 2-3 seconds until it goes into pairing mode. it will play a quick tone when it is connected similar to the goggles. Then you have to go into your goggles settings into "control" and change it from standard to "SBUS Baud fast". Then in betaflight, under the ports tab make sure you have selected the correct "serial rx" is enabled, the one that corresponds with the uart your air unit is connected to. Remember to save and reboot after navigating to a different menu. Then go to the presets menu and search for "DJI SBUS Fast", there are three options to choose from depending on what kind of pilot you are/aspire to be. But you must activate this for the controller to work, click pick and then save and reboot again. Then navigate to the receiver tab, Make sure receiver is set to "Serial(via Uart)" and serial receiver protocol must be SBUS, save and reboot and then it should work and it should move the bars in betaflight. Some of this might seem overly simple or maybe even a bit confusing, but I do not know what your technical level is at and believe this is the entire process. I hope this helps and if you have more questions feel free to ask and I will respond as soon as I can.

Hi. Please is it possible to use 2207 2050 KV motors instead?

@benjedonethat

2 ай бұрын

Absolutely possible! Just be careful on your first few flights, it is going to be a beast. If you are not super confident I would suggest putting an output limit on the motors. Lemme know if you wana know how to do that it is super simple and easy to remove later.

@raafatelnakib4236

2 ай бұрын

@@benjedonethat 😂 Your really scaring me as you mentioned is going to be a beast 😂 how do you do the motors limiter please?

@benjedonethat

2 ай бұрын

@@raafatelnakib4236 Lol! No need to be scared! Just be careful! Do not arm inside!! So in betaflight go to the PIF Tuning tab, then click on the Rateprofile Settings tab, then you will see sort of in the middle of the screen there will be a Throttle limit option. I would suggest using scale limit and start at 75%, it might be not as bad, then go to 85% or 90% and then 100 when you are completely comfortable with your quad. I hope this helps! Happy flying and let me know how it goes!

@raafatelnakib4236

Ай бұрын

@@benjedonethat thank you for the tip Sir, this will really help 🥰 By the way if I don’t install an anti spark filter will it cause any harm to the stack or it’s normal?

@benjedonethat

Ай бұрын

@@raafatelnakib4236 I do not use one on my build, it is a nice thing to have but it can work without it no problem, most quad do not have them at all. As long as you have a cap soldered on with your power leads, if you have an iflight stack they have them built in most of the time.