This video appears to be the first that shows how to build this beast! Hope this helps someone…
Жүктеу.....
Пікірлер: 29
@ivoiredrone5260 Жыл бұрын
Hey David, thanks a lot for a very helpful video. I am building my new Iflight Nazgul Evoque F6D V2, and had a hard time to figure out where to put the LED and Buzzer. Everything got easier after I saw your video. Thank you so much.
@pranavchimmula7752
Жыл бұрын
heyy, i am looking to build the same, confused on which frame type to buy, wondering what u got Squashed X or DeadCat ?
@ivoiredrone5260
Жыл бұрын
@@pranavchimmula7752
@ivoiredrone5260
Жыл бұрын
I bought the Deadcat version
@ikeflys
Жыл бұрын
Great to hear!
@ivoiredrone5260
Жыл бұрын
thanks a lot
@adamwetzli334122 күн бұрын
could you provide some information on what connector kit you used to manufacture the connector for the LED unit, please? I am already stuck at that part since I don't have this stuff at home
@slyfpv Жыл бұрын
Hi David ,thanks a lot for that helpful video I'm in the same build right now ,what an awesome frame kit ! Everything is in my kit except gps tpu ,not a big deal ,I would like to share with you one of my observation while reverse engineering that build : fiber optic motor end need to be plucked in green tpu motor bumper for full led effect !! , Nowhere there is any info about those details ,hope it help you ! Ciao buddy
@ikeflys
11 ай бұрын
This helped a bunch! Thanks!
@bbrkarting Жыл бұрын
Geez. Thank you so much.
@ikeflys
11 ай бұрын
You're welcome!
@jonmurph589 Жыл бұрын
Hey, thanks for uploading this. Just got the deadcat version. The exploded diagram leaves a lot to be desired as far as a build guide goes...
@ikeflys
11 ай бұрын
Glad it helped
@patty2Strk Жыл бұрын
good job thanks !
@ikeflys
Жыл бұрын
Glad it helped!
@andrec230 Жыл бұрын
Hi David, thanks for the video without him I wouldn't have been able to build the frame. I have a doubt if I use a 1875KV motor instead of the 1750KV that originally comes with the Nazgul I will increase de vlocity? Thanks again
@ikeflys
Жыл бұрын
Glad the video helped! I am not an expert on the motor sizes. However in my experience, not a big deal with Running 6s 1875KV vs 1750KV. I do not like going higher than that on 6S, I had a 1950KW and simply used 5S to get it the way I like. It's just a matter of your preferred flight preference's. Experiment and have fun!!
@andrec230
Жыл бұрын
@@ikeflys I'll do that David, thank you so much, happy fly👍
@OTRFlyer Жыл бұрын
Man thank you so much for having the foresight to make this video! I've always loved the nazgul because of the side plates and have looked since I got into this (about a year) for a nazgul frame and up until recently hadn't seen one! I found the 6 inch DC and ordered it immediately lol. I figured it only came pre-built. I've got the frame and stack and motors and vista, just gotta order the receiver. Do you think a diversity (crossfire) receiver will fit? With 2 Immortal T's? Anyway, I'm just getting started on the frame and plan to take my time but thank you for this cuzz I'd be lost without it! Your video is the only one I've seen! Can't find anything anywhere on this build! Not even iflights website lol! How'd yours turn out? Thanks again, your new sub!!
@OTRFlyer
Жыл бұрын
Oh and mine came with the wire you said you had to make. I think lol. It has two diff size plugs on it? I was going to put a picture in here but it won't let me... or I can't figure how lol! Thanks again!
@ikeflys
Жыл бұрын
Thats Great to know! Yeah had to make my LED connector. Another thing Someone else mentioned they got the correct XT-60 connector, but they ordered the Deadcat version. Curious, did you get the 5" squashed X like mine, or another version?
@ikeflys
Жыл бұрын
Glad I could be of help!! You probably already got it built by now. I do not know if the diversity fits, I only have experience with the nano version of crossfire.
@OTRFlyer
Жыл бұрын
@@ikeflys Hey, I got the dead cat 6 inch version. I've been working a lot and a little under the weather so haven't built it yet but I do have all the parts (hopefully lol)!! The xt60 I got seems to be correct but no room for mistake as the wires are barely long enough to reach the esc! Thanks for your videos! Thought about making one myself cuzz it's like you said, there aren't any nazgul build tips out there.
@lushfpv2605 Жыл бұрын
Hi can you please help me out with setting up LED in betaflight for this frame. Your video certainly helped me build. Appreciate your help. Thanks in advance.
@ikeflys
11 ай бұрын
Can’t remember, but I found a video. Try searching KZread for beta flight led control.
@friederek Жыл бұрын
Actually the fiber optic cable goes into the tpu motor mount. Theres a little hole to put it in 😉
@ikeflys
Жыл бұрын
I forgot to tell you thanks for pointing that. I started doing what you said
@bstanga Жыл бұрын
I have lost my single page of instructions, I've look all over and have not found it, any links?
@ikeflys
Жыл бұрын
The instructions are on iFlights site under support
Пікірлер: 29
Hey David, thanks a lot for a very helpful video. I am building my new Iflight Nazgul Evoque F6D V2, and had a hard time to figure out where to put the LED and Buzzer. Everything got easier after I saw your video. Thank you so much.
@pranavchimmula7752
Жыл бұрын
heyy, i am looking to build the same, confused on which frame type to buy, wondering what u got Squashed X or DeadCat ?
@ivoiredrone5260
Жыл бұрын
@@pranavchimmula7752
@ivoiredrone5260
Жыл бұрын
I bought the Deadcat version
@ikeflys
Жыл бұрын
Great to hear!
@ivoiredrone5260
Жыл бұрын
thanks a lot
could you provide some information on what connector kit you used to manufacture the connector for the LED unit, please? I am already stuck at that part since I don't have this stuff at home
Hi David ,thanks a lot for that helpful video I'm in the same build right now ,what an awesome frame kit ! Everything is in my kit except gps tpu ,not a big deal ,I would like to share with you one of my observation while reverse engineering that build : fiber optic motor end need to be plucked in green tpu motor bumper for full led effect !! , Nowhere there is any info about those details ,hope it help you ! Ciao buddy
@ikeflys
11 ай бұрын
This helped a bunch! Thanks!
Geez. Thank you so much.
@ikeflys
11 ай бұрын
You're welcome!
Hey, thanks for uploading this. Just got the deadcat version. The exploded diagram leaves a lot to be desired as far as a build guide goes...
@ikeflys
11 ай бұрын
Glad it helped
good job thanks !
@ikeflys
Жыл бұрын
Glad it helped!
Hi David, thanks for the video without him I wouldn't have been able to build the frame. I have a doubt if I use a 1875KV motor instead of the 1750KV that originally comes with the Nazgul I will increase de vlocity? Thanks again
@ikeflys
Жыл бұрын
Glad the video helped! I am not an expert on the motor sizes. However in my experience, not a big deal with Running 6s 1875KV vs 1750KV. I do not like going higher than that on 6S, I had a 1950KW and simply used 5S to get it the way I like. It's just a matter of your preferred flight preference's. Experiment and have fun!!
@andrec230
Жыл бұрын
@@ikeflys I'll do that David, thank you so much, happy fly👍
Man thank you so much for having the foresight to make this video! I've always loved the nazgul because of the side plates and have looked since I got into this (about a year) for a nazgul frame and up until recently hadn't seen one! I found the 6 inch DC and ordered it immediately lol. I figured it only came pre-built. I've got the frame and stack and motors and vista, just gotta order the receiver. Do you think a diversity (crossfire) receiver will fit? With 2 Immortal T's? Anyway, I'm just getting started on the frame and plan to take my time but thank you for this cuzz I'd be lost without it! Your video is the only one I've seen! Can't find anything anywhere on this build! Not even iflights website lol! How'd yours turn out? Thanks again, your new sub!!
@OTRFlyer
Жыл бұрын
Oh and mine came with the wire you said you had to make. I think lol. It has two diff size plugs on it? I was going to put a picture in here but it won't let me... or I can't figure how lol! Thanks again!
@ikeflys
Жыл бұрын
Thats Great to know! Yeah had to make my LED connector. Another thing Someone else mentioned they got the correct XT-60 connector, but they ordered the Deadcat version. Curious, did you get the 5" squashed X like mine, or another version?
@ikeflys
Жыл бұрын
Glad I could be of help!! You probably already got it built by now. I do not know if the diversity fits, I only have experience with the nano version of crossfire.
@OTRFlyer
Жыл бұрын
@@ikeflys Hey, I got the dead cat 6 inch version. I've been working a lot and a little under the weather so haven't built it yet but I do have all the parts (hopefully lol)!! The xt60 I got seems to be correct but no room for mistake as the wires are barely long enough to reach the esc! Thanks for your videos! Thought about making one myself cuzz it's like you said, there aren't any nazgul build tips out there.
Hi can you please help me out with setting up LED in betaflight for this frame. Your video certainly helped me build. Appreciate your help. Thanks in advance.
@ikeflys
11 ай бұрын
Can’t remember, but I found a video. Try searching KZread for beta flight led control.
Actually the fiber optic cable goes into the tpu motor mount. Theres a little hole to put it in 😉
@ikeflys
Жыл бұрын
I forgot to tell you thanks for pointing that. I started doing what you said
I have lost my single page of instructions, I've look all over and have not found it, any links?
@ikeflys
Жыл бұрын
The instructions are on iFlights site under support