As of 2023, your video is still helpful ... thank you!

you saved my transmitter!!!!! thankyouuuuuu

@BenjiNotknown

5 жыл бұрын

Glad I could help 😀

thanks.....you help so much....this cause by wrong baud rate setting, could be bad. ensure to set 11500. ;)

Legend. Arrived today and setting up timers / rssi and all that great stuff I bricked it. Just run the 10ch Programmer again and it's alive. Thanks a bunch for this

my i6 isn't bricked and i've successfully flashed it with the 10ch firmware but you never know what my happen in the future and I will keep this in mind, thanks for sharing.

I bricked my FS-i6 trying to flash the benb0jangles firmware to unlock 10 channels. Used this method to unbrick it, then immediately re-flashed benb0jangles and it worked! Thanks dude.

Thanks so much! when i got my tx bricked i was gone nuts, but then i did this and recovered

@BenjiNotknown

7 жыл бұрын

happy to know :)

Life savior !

that helped a lot! was about to go looking for new radio

You my dear sir..are a legend.. Thank you

You´ve saved my day. Thank you!

thanks so much

HEY!! thanks man! after brick ( flashing WHITE screen only), this helped !! thanks!! :D

You saved me ;) Thanks you!

I have a question, probably you can help me: one day my fsi6 start having strange isuue with the throttle position: when I turn it on it gives me warning message if the throttle is in low position but not when it is in up position. then I have to reverse the channel of the throttle. I went back to original firmware but nothing changed. than I update it again to 1.5 and than the tx wouldn't tun on anymore. luckily I found your video. Do you have an idea on what is going on in my TX? many thanks

hi how about ftdi that dint have 3.3 volt? is VCC connected to radio?

For this do I have to go to programming more?

Can I use the original cable that came with the FS-i6? Can somebody help?

Genial!! FAV, RT, LIKE, etc

Hey bro I need help. What's the purpose of the ftdi adapter? Because I connected the flysky to the computer without it and I don't know if I'll recover the TX. Thank you

@houseofpainINKS

5 жыл бұрын

i dont know ftdi means but i bricked mine , i turn it on and nothing, smh

N1 bro ..Thank You so much ..

Pro tip: I had to keep holding the trim buttons all the way during the flashing process for this to work. This may help some people that report this not working. (Eachine model)

@antonin6084

5 жыл бұрын

yeah thx a lot i had to keep holding those buttons too ! thanks schizo

thank you!

PLease HElp me My Transmitter Is Not Working AT All And Not Turning Up On Power what could Be the Problem

Thanks for this!

@vivianvincent427

8 жыл бұрын

+Ben Kistner HI there, can you share some info on how you got yours to work, mine still stays at 0% . Thanks

Awesome vid maan but....i don t know i click program and it stops at 100 percent and the radio doesn t turn on. Can you explan why does thet happen i don t understand Please.. i don t have money to buy another one

@lukaswenzel107

6 жыл бұрын

Have the same problem here. Did you figured it out yet?

HELP - my program goes to 100% but the flysky does not reboot!?

hii, it didnt work with my i6. it said that "connection failed". can you help me?

@houseofpainINKS

5 жыл бұрын

for what im seen this guy doesnt answer messages

Thank you, i've been bricked mine also and happened to unbricked it using MAVLINK updater, also from benb0jangles github. Flash MAVLINK using recovery method to unbricked, then re flash the HALI9 again. works with mine. github.com/benb0jangles/FlySky-i6-Mod-/tree/master/10ch%20Mavlink%20Mod%20i6%20Updater/10ch_Mavlink_MOD_i6_Programmer_V1

"see blog here:" Where?!

@BenjiNotknown

8 жыл бұрын

+gantz oops